R This product is not available for normal distribution.
SCB-1 Content Table of Contents 1. 2. 3. 4. 5. OUTLINE ...................................................................................................................................1 TECHNICAL SPECIFICATIONS .............................................................................................1 DIMENSIONS ............................................................................................................................2 PIN ASSIGNMENT..................................................
Outline SCB-1 1. OUTLINE The SCB-1 is an ultra-compact color-camera-module with XGA-resolution (1024x768) and 20 frames per second. With the integrated frame-rate-converter the camera is able to produce a 60Hz or 75Hz XGA-image. The SCB-1 has a high quality lens with 12x optical zoom and 2x digital zoom. The camera module has an auto-focus. There are special features like: 9 Presets (remain stored when disconnected from power), Positive/Negative, 4 image memories plus Freeze.
SCB-1 Dimensions 3.
Pin Assignment SCB-1 4.
SCB-1 Pin Assignment J6 Serial Control (RS-232) Board side: JST S3B-ZR Cable connector housing: JST ZHR-3 Pin 1 Pin 2 Pin 3 RxD TxD GND RS-232C, 9600baud, 8, n, 1 (Data from host) RS-232C, 9600baud, 8, n, 1 (Data to host) The baud rate is changeable up to 921600 baud for image transfer. J18 Power Board side: JST S2B-ZR Cable connector housing: JST ZHR-2 Pin 1 Pin 2 +12V DC; (0.5A typical, 0.
Functions SCB-1 5. FUNCTIONS The SCB-1 can be controlled through a key-matrix or via RS-232 (SCOTI). With the WolfVision SCB-1 Interface board the basic control functions can be done for evaluation-purposes. 5.1 ZOOM The SCB-1 uses an 12x zoom lens as well as a 2x digital zoom. Optical 12x, f=5.8 to 69.6 mm (F=2.8 to 3.0) The digital zoom is automatically switched ON at the tele end of 12x optical zoom range, with progressive effect from 1 to 2, giving a total maximum 24x zoom ratio.
SCB-1 Functions Auto Iris (AI) The iris changes automatically according to the brightness of the subject. If ASC and / or AGC are enabled, they change also automatically if necessary. Auto Shutter Control (ASC) If enabled, the shutter virtually extends the iris-range if the iris is closed as much as possible. If disabled, the shutter can be set from 1 (very short exposure time) to 1188 (maximum exposure time).
Functions SCB-1 White balance adjustment errors If the white balance adjustment is not successful, an error message appears on the screen. If this happens, take the necessary measures. Error message White: Too Bright! White: Too Dark! White: Out of Range! Description and remedy The video signal level is too high.
SCB-1 Functions 5.8 On-Screen Menu By pressing the MENU-key for 1 second, the on-screen menu appears on the screen. To navigate in the menu, use the UP/DOWN-keys, LEFT/RIGHT-keys. The standard settings are in italics. The menu can not be operated via SCOTI.
Control Methods SCB-1 6. CONTROL METHODS Basic camera functions can be controlled by the interface board.
SCB-1 Control Methods The Camera can be also controlled via RS-232. Controller D-SUB 9pin Camera J6 JST ZHR-3 1. RxD 1. CD 2. RxD 3. TxD 4. DTR 5. GND 6. DSR 7. RTS 8. CTS 9. RI 2. TxD 3. GND Controller D-SUB 25pin 1. FG Camera J6 JST ZHR-3 2. TxD 3. RxD 4. RTS 5. CTS 6. DSR 7. GND 20. DTR 1. RxD 2. TxD 3. GND For more details, see the command list on page 14.
Installation SCB-1 7.
SCB-1 Eclipse 8.
Handling and Precautions SCB-1 9. HANDLING PRECAUTIONS 9.1 Handling Avoid spilling water or any liquids on to the camera. Do not allow metallic objects to fall inside the body or contact the electronic boards. 9.2 Operation and storage locations Avoid operation or storing the camera in the following locations: • Extremely hot or cold places (operation temperature: 0°C to +40°C) • In direct sunlight for long periods, or close to heating equipment (e.g.
Command List 10. SCB-1 COMMAND LIST 10.1 Specification of SCOTI (SCB Operating & Transfer Interface) Overview The SCB-1 can be controlled via a RS-232-interface. The used protocol is called SCOTI (for SCB operating and transfer interface). The baud rate is set to 9600 (8, n, 1, no handshaking) out of the factory. It can be changed to 19200, 38400, 57600, 115200, 230400, 460800 or 921600. The high transfer-rates are useful if you want to transfer images via RS-232 (not possible with 9600).
SCB-1 Command List Packet-Format Short-Packet-Format: For short packets (up to 15 Byte Data): 00hex Len+F0hex Data[1] Data[2]... Data[Len] Checksum Long-Packet-Format: For long packets (up to 61439 Byte Data): 00hex Len H Len L Len-Checksum Data[1]... Data[Len] Data-Checksum The long-packet-format-data can also be used for short packets (below 15 bytes of data). (However, only one of the two possible formats will be used in this document.
Command List SCB-1 Version Check A special command, which is the only command that does not use the packet-format is 76hex (ASCII 'v'). If the camera receives this command, it will respond with "SCB-1 Vx.xxx"+CR+LF. This command can be used for easy communication-check with a terminal program and is also included for compatibility with other WolfVision Products. Replies from the camera Command OK: H 00 L F1 D 01 C 0D Remarks reply within max. 0.
SCB-1 Command List Zoom Function Zoom Tele H L 00 F2 01 20 C Remarks with Speedup after 1 sec, disables freeze / memories with Speedup after 1 sec, disables freeze / memories Zoom Wide 00 F2 01 30 C Zoom Stop 00 F2 01 10 C Optical Zoom Tele w/ var. Speed Optical Zoom Wide w/ var.
Command List SCB-1 Focus Function H L Remarks Focus Near 00 F2 02 20 C Focus Far 00 F2 02 30 C with Speedup after 1 sec, switches AF off, disables freeze / memories with Speedup after 1 sec, switches AF off, disables freeze / memories Focus Stop 00 F2 02 10 C Focus Near w/ var. Speed Focus Far w/ var.
SCB-1 Command List Iris Function H L Remarks Iris Open 00 F2 03 20 C Iris Close 00 F2 03 30 C with Speedup after 1 sec, switches AI off, disables freeze / memories with Speedup after 1 sec, switches AI off, disables freeze / memories Iris Stop 00 F2 03 10 C Iris Open w/ var. Speed Iris Close w/ var.
Command List SCB-1 White Balance Function H L Remarks Manual WB 00 F2 04 50 C Perform One-Push-WB 00 F2 04 51 C Auto-Tracking WB 00 F2 04 52 C Set Manual WB 00 F4 04 40 PR PB C Get WB-Settings 00 F2 04 60 C Reply: 00 F4 60 R B M C PR: Red gain (-120dec to 120dec) PB: Blue gain (-120dec to 120dec) (Twos-Complements) R: Red Gain (-120dec to 120dec) B: Blue gain (-120dec to 120dec) M: 0=ATW, 1=AWB, 2=Manu Presets Function H L Remarks Store Preset 00 F3 05 40 P C P=Preset no.
SCB-1 Command List User I/O Function H L Set User LEDs 00 F3 07 40 P Get User Keys 00 F2 07 60 C Remarks C P=LED-Bit-Pattern (0 to 7), if Bit is set, LED is on.
Command List SCB-1 Image Transfer Function H L Remarks Capture Picture 00 F4 09 10 PM PC C Get Picture Block 4k 00 F2 09 60 C PM=Memory: 0=Live, 47=Memory 0-3 PC=Capture Mode: 0: Full Resolution 80-8F: Updated Preview Tile 0-15 C0-CF: Not Updated Preview Tile 0-15 Not available at 9600 baud. Not available at 9600 baud. Get Picture Block 1k 00 F2 09 61 C Not available at 9600 baud.
SCB-1 Command List User OSD Function H L Remarks Activate User OSD and Clear OSD 00 F2 0A 10 C Disable User OSD 00 F2 0A 11 C First line double Height on First line double Height off Set line color 00 F2 0A 12 C Enables User-OSDCommands and resets the OSD. SCB-1-OSD-Messages and Menu are suppressed. Disables User-OSDCommands and allows Menu and SCB-1-Messages. Default: off 00 F2 0A 13 C 00 F4 0A 40 PL PC C PL: Line (0 to 14), PC: Color (0 (black) to 7 (white, default)) 00 Fx 0A 50 PL PC PT ...
SCB-1 11. SCB-Control Software WolfVision Camera Control Software The WolfVision Camera Control Software can be used to operate the SCB-1 XGA-colorcamera via SCOTI (RS-232). It is also possible to transmit images in preview- and fullresolution to the PC. Software Installation Install Camera Control software (available on supplied CD-ROM or downloadable from Internet http://www.wolfvision.com/wolf/camera_control.exe).
SCB-Control Software SCB-1 Control of the SCB-1 Basic functions like Zoom and Focus are accessible on the left-side of the main-screen. For further functions use the Control Panel (SCB-1 Interface board) or the User OSD Panel in the Functions Menu. Virtually all commands can be performed with this program (the commands without a button can be performed by entering the code directly in the "Extras - Custom Command"-menu).
SCB-1 SCB-Control Software Key Lock If the camera doesn't react to a keystroke (keys on the camera itself and on the IR-remote control), then check if the keylock is activated. Firmware update Download new firmware from the Internet (http://www.wolfvision.com/wolf/fware.html#c). Hints For the image-transfer, the serial port is the bottleneck, because a lot of data has to be transmitted. To reduce this bottleneck, the SCB-1 support baud rates up to 921600 baud.
Optional Accessories 12. SCB-1 OPTIONAL ACCESSORIES The sample kit includes a high speed RS-232 extension card and the WolfVision interface board, all necessary cables (5 pieces) and a power supply. The proxer (close up lens) is not supplied normally. 12.1 High speed RS-232 extension card 12.
SCB-1 Optional Accessories 12.3 Proxer Technical data: f=477mm, 2.1 dpt.
Notes SCB-1 R 29
SCB-1 Optional Accessories R CONTACTS: Manufacturer / Worldwide distribution: WolfVision GmbH, Vlbg. Wirtschaftspark, A-6840 Götzis / AUSTRIA, Tel. ++43-5523-52250, Fax. ++43-5523-52249, E-Mail: wolfvision@wolfvision.com Internet Homepage: www.wolfvision.com E-Mail to technical support: support@wolfvision.com American distribution: WolfVision USA East Inc., 3950 Shackleford Road, Suite 450, Duluth, GA 30096 / USA Tel. (770) 931-6802 and 1-877-873WOLF, Fax: (770) 931-6906, E-Mail: usa.east@wolfvision.
