01 Checking the Components Soundbar Remote control User's guide Va Stereo RCA to Digital Optical cable 3.
02 Product Overview Control Pan! of the Soundbar i Short Press te change the input mode, LED screen show current mode. Fl | Power on/off button 3] Long press to adjust the volume, when adjusting, LED screen will showed the number Short press to perv song or next song under BT and USB mode 0 Pause/play under BT and USB mode; telecommute under the AUX, optical, coaxial and ARC mods. +» When you plug in the power cord, the buttons will begin working seconds.
Rear Panel of the Soundbar USE, connect a USE device here {o play music files on the USB device through the Soundbar. Digital Audio In (optical), connect to the digital (optical) output of an external device, Coaxial Audio In (coaxial), connect to the digital (coaxial) output of an external device. TV ARC, Conner to the ARC output of an external device. AUX. connect to the Analog output of an external device. Bremen DC IN (Power Supply In), connect the AC/DC power adapter.
03 Connecting Electrical Power 1. Using the power adapter to connect the unit to electrical outlet in the figure 2, Press the power button to power on the Soundbar (LED screen will turn on) « Make sure to rest the AC/DC adapter flat on 2 table or the floor. If you place the AC/DC adapter so that it is hanging with the AC cord input facing upwards, water or other foreign substances could enter the adapter and cause the adapter to malfunction.
04 Connecting with TV {Choose only 1 method) Method 1. Connecting using Optical cable 1. Connect the DIGITAL AUDIO IN(OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV with a digital optical cable’ 2.Select “OPT” on LED screen by pressing the “MODE” button on the remote or control panel.
Method 2. Connecting using Coaxial cable | coaxial our | _@ | Coaxial digital cable (not supplied) 1. With the Soundbar and TV turned off, connect the Coaxial cable as shown, 2. Turn on the TV and soundbar, select “COA” on LED screen by pressing the “MODE” button on the remote or control panel. » You must use Sandbar's remote te power on ar control the volume under this connection.
Method 3. Connecting using ARC cable ARC cable{not supplied) 1. TV ARC connection transmits digital audio signals between devices. If your TV have TV ARC connector, using therm will provide the best possible audio performance quality. * Using a Version 1.4 or above of TV ARC cable (not supplied). » Connect the cable to the TV's TV ARC out to the Soundbar TV ARC in. « Turn on the TV and soundbar, select “ARC” on LED screen by pressing the “MODE” button on the remote or control panel. 2.
Good to know for TV setting Please note almost all the TV audio output is the analog signal and the internal speaker, but the optical cable and coaxial cable is the digital signal, so when you want to hook up the soundbar on your TV through optical or coaxial cable, you must change the TV audio output to digital outputted or SPIFF) and external speaker How to set PCM on your TV 1.Enter your TV's settings many 2.Select the Audio or sound settings option 3.Select the audio out or digital out setting 4.
Method 4. Connecting via AUX ro curate supplied) AUK jack Sammy to RCA cable (supplied) 1 Use the 3.5mm to RCA audio cable to connect the TV's stereo Audio output socket to the AUX jack of the unit, Or use the 3.5mm to I.5mim audio cable {not supplied} to connect the TV's AUX output jack to the AUX jack of the Speaker. electable * AUX" on LED screen by pressing the “MODE” button on the remote or control panel. if rio sound or echo, set your TV's audio output to external speaker.
05 Connecting an External Device BD / DVD Set tap box / Game console Optical digital cable (supplied) Coaxial digital cable {not supplied) 3 — EJ ARG cable (not supplied) a] Pearl rot E540 3.5mm AUX cable rot supplied oo © | HEE Or 35mm ta RCA cobble (supplied) Chaplin wed §} Optical Carla #1 © 1. Connect DIGITAL AUDIO (OPTICAL) on the Soundbar to the OPTICAL GUT jack of the Source Device using a digital optical cable. 2.
06 Connecting a USB USE Device 1. Connect your USB device to the USB jack on the Soundbar. 2. Select “USB” on LED screen by pressing the “USE” button on the remote. 3. Play music files from the USB device through the Soundbar.
07 Connecting a BT Device BT Device The initial connection 1. Select “BT” on LED screen by passing the “BT” button on the remote. 2. Turn on BT on the BT device. ( see the device's manual for mots information) 2. Select “HOME 588” from the fist, connect it. When your BT device is connected, the LED screen will keeping display BT . 4, Play music files from the device, connected via BT, through the Soundbar * You cannot connect mare than one BT device at a time.
Additional BT Information 1. If you hear any bra ask-up while streaming music from your device, move closer to your Soundbar 2. BT signal has a range feet if there are no solid obstructions between your Soundbar and source device. 3. Other wireless cicadas may interfere with BT range, including wireless video monitors, cordless phones, wireless cameras, etc, moving or truing off these devices may improve BT range.
08 Soundbar Wall installation Diagram Tools & Firings received 1/. Drill sifted with masonry drill bit 2/. Screwdriver 3/. Pencil 4/. Ruler 5/. Spirit level + Place the soundbar in the desired position and using a spirit level check that the soundbar is level. = Make a light pencil mark on the wall at the top edge of both fixing brackets. The mark should be positioned directly above each bracket. Note the mounting points on the soundbar (one is S4.5mm from the end while the other isS4.
08 Know Your Remote Power the remote by inserting 2 pos of AAA batteries e Power on/Off Mute Choose the mode of the BT/USB/ARC/OPT/COAX/AUX Increasing the total volume Rev.
Troubleshooting Ne Sound 1. Please check if the sandbar is consistent with the input made of Sound Sorties by following the manual 2. Press the Volume+ button on the remote or soundbar to volume up. 3. Please check the output devices if the output of sound source is working. Please make sure all the soundbar ports are input ports and all the connected devices are audio output. [Mo sound when TV is 1. Set up the optical output. 2. Set up the audio output format--PM, 3.
The remote is nat working 1. Please check If the positive and negative of battery is Eight. (There Is noted on the battery compartment) 2. Please check if the receiving location is blacked beside the LED on sandbar. 3. The working distance of remote Is 6-m (empty placard. Please make sure afl the soundbar ports are Input ports and afl the connected devices sre audio output, The sound Is kaw or bad Tha sound Is inconstant with the sound of TV 1. lens lama suns if the bohemianism of output device is big. 2.
10 Important Notes About Service Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. 11 Specifications Sound Bar: Inputs: Frequency Response (System): Compliance: Place of Origin: 2.25" TWO Full Rang Driver x 2 + Air Tube x 1 One AUX Stereo Audio One USB One ARC BT (Wireless) One Optical One Coaxial 50 Hz to kHz FCC.
Thanks for reading! Edi bl Rd ec eee Re ee Bros para GILT LANE eR BGT BY NOTE: Ome year warranty, 45 days money back guarantees, (lifetime technical snort, 100% satisfaction service, please feel free to contact us for any questions,