en tia l Co nf id User Guide W NC 5G CPE
Federal Communication Commission Interference Statement en tia l This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety Warnings en tia l Adapter Do not use any other power adapter except the one that accompanies this unit or a power adapter identified in the list below. Use of another adapter could result in damage to the unit. The following power adapter is qualified for use with this Verizon 5G Home Router: This unit must be powered by Delta, model ADP-48GR BA or equivalent UL listed power source rated @ output 12Vdc, Maximum 4.0A. Battery Do not use any other battery.
Table of Contents FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT .................................................................. I RADIATION EXPOSURE STATEMENT ................................................................................................................ I SAFETY WARNINGS .................................................................................................................................... II CHAPTER 1 INTRODUCTION ................................................
Chapter 1 Introduction This chapter includes a list of items included with the CPE, the minimum system requirements for using the Verizon 5G CPE, and an overview of the CPE’s features. Package Contents en tia l 1.1 The product package of LVSK should contain the following items: 5G CPE LVSK Assembly (LVSKODU + LVSKIDU + LVSKCRA) x 1 set Window bracket with window wipe x 2 set Power Adapter & AC Power cord x 1 set Cable clip x 2, window wedge with Velcro strip x 2 1.
en tia l nf id Below describe the connectors on LVSKIDU Power Jack The Power Jack connects the LVSKIDU to an electrical outlet via the power cord. Ethernet Ports The Ethernet Port enable you to connect devices to the FCL Router via Ethernet cable with class better than CAT5e. Co USB type C port This USB port connect LVSKIDU to LVSKODU to provide communication.
3 W NC Co nf id en tia l
en tia l Battery Cradle Co LVPK nf id Below contains a description of LED and button on the bottom of cradle.
PoE Port The PoE Port enable you to connect LVPK device to the FCL Router via shielded Ethernet cable with PoE power injector and surge protection boxes in series. USB type C port This USB port connect LVPK to LVSKODU to provide communication in between. en tia l Below describe the USB cable on LVSKODU USB cable W NC Co nf id This USB cable attached to LVSKODU to provide communication with LVSKIDU or LVPK when cable plug in.
Chapter 2 Connecting the CPE – Type #1 This section describes how to install 5G CPE as Type #1 configuration. Configuration #1 5G CPE Installation Overview 2.2 Open Box – Full Set CPE nf id User open box and see both units with the cradle as a whole set USB cable is plugged in and collected at central retention bar DC cable is plugged in and routing from the bottom Press the battery button under cradle to enable battery power. Please check the LED on the bottom of cradle.
2.4 Install 5G CPE at the window Co 2. Install on the Window nf id 1. Unload CPE From The Cradle en tia l 6. Please go to section 3 if no good 5G signal can be achieved. Connect to FCL Home Router NC 2.5 1. Connect by WPS of Wi-Fi LVSKIDU: Short Press Mode/WPS button, IDU will start WPS as an AP. FCL Router: Long press WPS button, FCL will start WPS as a client. IDU and FCL Router will connect by the backhaul SSID W 2.
Chapter 3 Connecting the CPE – Type 2 This section describes how to install 5G CPE as Type #2 configuration, when Type #1 configuration can’t provide good communication quality. To assemble LVSKODU with LVPK To decide good location with good signal quality for device installation To install bracket and device To connect to FCL router 3.2 To assemble heatsink with ODU. To plug ODU to bottom housing.
en tia l To connect to FCL router nf id 3.5 W NC Co 1. To connect Ethernet cable between PSE (Ethernet input port) and FCL (Ethernet WAN port). 2. To connect shielded Ethernet cable between SPU and PSE (PoE power injector) Ethernet output port. PSE power cord need to plug in. 3. To mount SPU (surge protection device) on wall and do grounding. 4. To connect 5G CPE and SPU by shielded Ethernet cable (Cat5e or better).
Appendix: Specifications en tia l Product specifications Cradle Battery 3.6V 3450mAh LVSKIDU Ethernet CAT6 2.5Gbps Memory DDR3: 512MB NAND: 256MB Co Embedded Antenna 5G WiFi x 4 nf id Wi-Fi 5G 802.
PoE 802.3bt 60W 2.5Gbps en tia l Memory DDR3: 512MB NAND: 256MB Mechanical Specifications Cradle LED x 1 DC jack x 1 Battery button x 1 Cable with DC plug x 1 nf id LVSKIDU Co LED for 5G signal quality indication × 1 (Tri LED) LED for router status indication × 1 (Dual LED) Buzzer x 1 2.
Storage Temperature –45°C to 70°C W NC Co nf id en tia l Shipping and Storage Relative Humidity 5% to 85% 12
