WizFi630A User Manual (Version 1.0) © 2015 WIZnet Co., Ltd. All Rights Reserved. For more information, please visit our website at http://www.wiznet.co.kr © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
FCC Statement 1. NOTICE; A. The RF module is limited to OEM installation ONLY. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. B. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. C.
4. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that minimum 20 cm is maintained between the antenna and users, and the RF module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. 5.
Document Revision History Date Revision 2015-03-02 1.0 Changes Release - © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
1. Introduction ............................................................................. 5 1.1. 1.2. 1.3. 1.4. 1.5. 1.5.1. 1.6. 2. Features ..............................................................................................................................................6 Wireless Specifications .................................................................................................................7 Hardware Specifications...............................................
2.5.4. 2.6. 2.6.1. 2.6.2. 2.6.3. 2.6.4. 2.6.5. 2.7. 2.7.1. 2.7.2. 2.7.3. 2.7.4. 2.7.5. 2.7.6. 2.7.7. 3. Hardware Information ........................................................... 47 3.1. 3.2. 4. Ethernet Data Tagging Option ..................................................................... 38 Firewall settings ............................................................................................................................ 39 DMZ .......................................................
1. Introduction WizFi630A is a gateway module that transforms the RS-232 protocol and TCP/IP protocol into IEEE802.11 b/g/n wireless LAN protocol. WizFi630A enables a device with RS-232 serial interface to connect to LAN or WLAN for remotely control, measuring, and administration. WizFi630A can also work as an IP router because of its internally embedded switch.
1.1. Features Complies with IEEE802.11b/g/n. Gateway/AP(Bridge)/AP-Client/Client(Station)/Ad-hoc Mode , WDS/Repeater supports 1T1R RF Interface Physical link rate up to 150Mpbs Built-in 3 Ethernet Ports 2 Serial Ports supports Working as Wi-Fi Router WEP 64/128bit, WPA/WPA2-PSK TKIP, AES 802.1x (Only in AP mode) 802.11e and WMM (Wi-Fi Multimedia) Router and Firewall function supports © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
1.2. Wireless Specifications Type Wireless Standard Description IEEE802.11b/g/n USA: 2.400 ~ 2.483GHz Frequency Range Europe: 2.400 ~ 2.483GHz Japan: 2.400 ~ 2.497GHz China: 2.400 ~ 2.483GHz USA/Canada: 11(1 ~ 11) Major Europe Countries: 13(1 ~ 13) Operating Channels France: 4(10 ~ 13) Japan: 14 for 802.11b(1 ~ 14), 13 for 802.11g(1 ~ 13) Korea/China: 13(1 ~ 13) 802.11b: -89dBm@11Mbps Receive Sensitivity 802.11g: -74dBm@54Mbps 802.11n(40MHz): -66dBm@150Mbps 802.11n(20MHz): -70dBm@72Mbps 802.
1.3. Hardware Specifications Type Description Serial port : 2 EA Interface LAN port : 3EA USB port : 1 USB Host Port ( Reserved ) U.FL(wireless) Temperature Humidity Operation: -10℃~70℃ Operation: 10% to 90%, Non-Condensing Storage: 5% to 90%, Non-Condensing Baud Rate : 1200 ~ 921,600bps Stop bits: 1, 2 Serial Parity: None, Odd, Even Flow Control: UART1: XON/XOFF(software), CTS/RTS(hardware), none UART2: XON/XOFF, none Input Power Power Consumption Dimension Weight DC 3.3V / 1A Max : 3.
1.4. Software Specifications Type Operation Mode Protocol Description Access Point(Bridge), Client(Station), Gateway, AP-Client, ad-hoc TCP, UDP, ARP, ICMP, DHCP, PPPoE, HTTP WEP 64/128bit Security WPA/WPA2-PSK AES/TKIP 802.1x ( Only in AP Mode ) Configuration Notification Serial To Wi-Fi Web Configuration, Serial Command, Configuration Tool Event Logging 2 Serial Port supports Table 3. SW Specifications 1.5. EVB Construction 1.5.1. Section Contents Qnt.
2dBi WI-FI Antenna (Model : W5I-B0-08) Antenna 1 ea Serial Cable Serial Cable 1 ea LAN Cable LAN Cable 1 ea DC 5V/2A Adapter Adapter 1ea Table 4. WizFi630A-EVB Contents © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
1.6. Block Diagram Figure 1. WizFi630A Block Diagram © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
2. Operation Mode and Description of Menu 2.1. Operation Mode User can select the operation mode. The default setting of WizFi630A is AP Mode. (DHCP Server Enabled) DHCP Server is usually disabled in AP mode, but for the user’s convenience, DHCP Sever will be enabled. 2.1.1. Access Point In this mode, all Ethernet ports and the wireless interface are bridged together. Wired/Wireless interface has the same IP address space with its top mesh.
2.1.2. Gateway When operating in router mode, interfaces are separated into WAN I/F (Top Internet Business Network), LAN I/F (Sub Private Network: 192.168.16.xxx), and Wireless I/F (Sub Private Network: 192.168.16.xxx). Port # 0 will be assigned to the WAN Port. WizFi630A periodically sends Broadcast Packet to Sub-LAN (LAN Port included) and maintains connection with Station. 2.1.3. Client (Station) Wireless I/F is assigned as WAN Port and all Ethernet Ports are bound to LAN Port.
2.1.4. AP-Client Mode Wireless I/F is assigned as WAN Port and all Ethernet Ports are bound to LAN Port. This mode is similar to Station mode, however the difference is that the Wireless I/F will operate as client with AP simultaneously. WizFi630A periodically sends Broadcast Packet to Sub-LAN (LAN Port included) and maintains connection with Station. © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
2.2. Menu List by Operation Mode 2.2.1. Access Point (Bridge) Mode Menu Internet Setting Wireless Setting Detailed Menu List Number System IP Internet connection setting 2.3.1 LAN Local network setting 2.3.2 DHCP Clients DHCP Client Information 2.3.3 VPN Config VPN setting 2.3.4 QoS(802.1p) QoS(802.1p) Setting 2.3.6 Basic Basic settings 2.4.1 Advanced Advanced Wireless Settings ( AP Mode ) 2.4.2.1 Security Wireless Security setting 2.4.3 WDS WDS Setting 2.4.
2.2.2. Gateway (Router) Mode Menu Internet Setting Wireless Setting Detailed Menu Internet connection setting 2.3.1 LAN Local network setting 2.3.2 DHCP Clients DHCP Client Information 2.3.3 VPN Config VPN setting 2.3.4 Routing Static Routing Setting 2.3.5 Qos(802.1p) QoS(802.1p) Setting 2.3.6 VLAN(802.1q) VLAN(802.1p) 2.3.7 Basic Basic settings 2.4.1 Advanced Advanced Wireless Settings ( AP Mode ) 2.4.2.1 Security Wireless Security setting 2.4.3 WDS WDS Setting 2.4.
2.2.3. Client (Station) Mode WizFi630A works as a Wi-Fi client(station) which is always paired with a Wi-Fi AP. Users can take Client Mode as an opposite of Gateway Mode Menu Detailed Menu Description ( Link ) List Number WAN Internet connection setting 2.3.1 LAN Local network setting 2.3.2 DHCP Clients DHCP Client Information 2.3.3 VPN Config VPN setting 2.3.4 Routing Static Routing Setting 2.3.5 Qos(802.1p) QoS(802.1p) Setting 2.3.6 VLAN(802.1q) VLAN(802.1p) 2.3.
2.2.4. AP-Client Mode AP-Client Mode Settings are very similar to the Gateway Mode Settings. The table below shows the added features of AP-Client mode. One module can operate as both AP and Station. The wireless module connects to a different AP and functions as WAN port. The channel of WizFi630A must be identical to the channel of AP to be connected Support wireless bridge. Menu Detailed Menu Description ( Link ) List Number WAN Internet connection setting 2.3.
System Status System Status 2.7.6 System Log System Log 2.7.7 © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
2.3. Internet Setting 2.3.1. Internet connection setting Select the internet service type and WizFi630A can connect to the internet If users would like access to Internet, Gateway Mode should be selected. Type Description Select the communication ways for Internet’s connection WAN Connection Type - Static(Fixed IP) - DHCP (Auto config) - PPPoE Settings about module’s host name Host Name Some ISPs require that you register a MAC address.
2.3.3. DHCP Client Information The IP information that is assigned from the DHCP server is shown. Type Host name Mac Address Description Client’s host name is shown Client’s MAC address is shown. IP Address Client’s IP address is shown. Expires in The usable time of client’s IP address is shown. 2.3.4. VPN setting This section will explain on VPN packet settings. Type L2TP Pass-through IPSec Pass-through PPTP Pass-through Description Enable : VPN L2TP packet is passed through WAN.
2.3.5. Static Routing Setting User can modify the routing table at static routing settings. We do not recommend any modification. Type Destination Range Description Enter the Target IP address or network address. Select whether the routing table is HOST or NETWORK Netmask If Range is NETWORK, enter subnet mask. Gateway Enter the gateway address to be passed when communicating with target. Interface Select whether the target is LAN or WAN. 2.3.6. QoS(802.
2.4. Wireless setting 2.4.1. Basic settings This chapter is about basic setting for wireless LAN. Type Radio On/Off Description Decide radio on/off of wireless AP function. 11b/g/n mixed mode: 802.11b/g/n are supported. 11b/g mixed mode: 802.11b/g are supported. Network Mode 11b only: only 802.11b is supported. 11g only: only 802.11g is supported. 11n only: only 802.11n is supported SSID Broadcast Network Name Frequency(Channel) Enter the name of the wireless network.
2.4.2. Advanced Wireless Settings 2.4.2.1. Advanced Wireless Settings ( AP Mode ) Only works at the AP Mode, Gateway Mode, and AP-Client Mode This chapter is about higher-level setting for wireless LAN. Type Description Controls the range of wireless radio being sent. The range of wireless radio being sent Tx Power gets larger as the value is larger. The wireless speed can be maximized by enabling this function.
User cannot use wireless LAN if user clicks RADIO OFF. Wireless Mode Country Region Code B/G Protection HT BW GI MCS Selects wireless mode. Selects the country / regional code. Setting for better wireless communication when both 11b and 11g LAN cards are used. We recommend Auto. Select whether the PHY Mode of wireless to be Mixed Mode or GreenField Mode. Fix the channel bandwidth to 20MHz: 20MHz. 20/40MHz: Use 40MHz when wireless station that supports 11n channel bonding.
2.4.3. Wireless Security This chapter is about settings for wireless network security Type Description SSID choice If multiple SSID are in use, choose the corresponding SSID for security. Security Mode Select security mode. Disable : Access Control function will be disabled.. Access Policy Allow Listed : allows communication with listed MAC client. Reject Listed: blocks communication with listed MAC client. Add a station MAC Enter the client’s MAC address for controlling. 2.4.3.1.
2.4.3.2.1. WEP Enter key for WEP64 or WEP128 network. Use either character string or hex character when entering key. Select 1~4 for ‘Default Key.. Enter at least one WEP Key. The entered WEP key is used for connection from wireless terminal. 2.4.3.2.2. TKIP/AES authentication Enter at least 8 characters of character string for the network key value. 2.4.3.2.3. Wireless 802.1x authentication Enter the value for linking with the Radius Server.
2.4.4. WDS(Wireless Distribution System) Setting Connection with different AP is possible with WDS (Wireless Distribution System) function. Maximum of four APs can connect through WDS function. 2 APs must use the same channel and authentication / encryption method Type Disable Description WDS function is not used. (Default disable) Do not register the MAC of AP to be connected. Lazy Mode Connect the AP’s MAC to the registered AP. AP function is provided. Register the MAC of AP to be connected.
2.4.5. WPS Setting 2.4.5.1. WPS Setting ( AP Mode ) Only work at the AP Mode, Gateway Mode and AP-Client Mode The WPS function enables easier wireless network setting. Type Description WPS Enable / Disable WPS. WPS Current Status Shows whether WPS is used or not for the connection with station. WPS Configured Shows whether WPS is configured or not. WPS SSID Shows the SSID connected to the station. WPS Auth Mode Shows the authentication used with WPS.
2.4.6. Wireless network status The status of the station that is connected to WizFi630A is shown. The surrounding wireless AP’s status are shown. Type Channel SSID BSSID Security Signal W-Mode Type Description Channel information of AP SSID of AP MAC address of AP Encryption method of AP Signal strength with AP Wireless mode of AP Network Type of finding AP In: Infrastructure, Ad: ad-hoc © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
2.4.7. AP Wireless Statistics The Statistics of wireless communication is shown. 2.4.7.1.
2.4.8. Station QoS/DLS(Direct Link Setup) Configurations Set Station QoS / DLS configurations in station mode Type WMM(Wi-Fi Multimedia) WMM Power Saving Description Enable WMM function or not. Enable Power Saving function or not. Enable Direct Link function or not. Direct Link Setup In order to use Direct Link function, the AP connected to WizFi630A and the Station to be connected must support Direct Link function.
2.4.9. Profile Shows the profile of the connected AP. The profile information can be modified. By using “Site Survey”, it is very convenient to find and connect with an AP. Administration of maximum of two AP is possible after adding to profile. The module automatically connects to the active AP (selected AP) upon booting. Type Profile SSID Channel Authentication Encryption Network Type Description Profile Name SSID of AP to be connected Channel information of AP to be connected.
2.4.10. Link Status Shows the link status between wireless LAN and AP. Type Status Extra Info Channel Link Speed Throughput Link Quality Signal Strength Noise Level Description SSID and BSSID of connected AP. Link status. Channel information of connected AP. Link speed rate of connected AP. Real performance through communication. Link quality of connected AP. Signal strength of connected AP. Noise level of connected AP. The HT section only appears when connected with 802.11n AP.
2.4.11. Site Survey Site Survey searches for AP surrounding WizFi630A. Select an AP and click the connect button (If the module is rebooted, the module will connect to the previous profile). Click “Add Profile” if user wishes to add to profile. Type SSID BSSID RSSI Channel Encryption Authentication Network Type Connected Connect Rescan Add Profile Description SSID of searched AP Wireless MAC Address of searched AP. Signal strength of searched AP. Channel of searched AP.
2.4.12. WIFI Multi-Bridge settings Set WI-FI Multi Bridge Mode in AP-Client mode. Type Description Select Gateway or Bridge Mode. Operation Mode Wi-Fi is WAN: operates in Gateway Mode. Multi-Bridge Mode: operates in Bridge Mode. SSID Frequency (Channel) MAC Address Security SSID of AP to be connected. Channel of AP to be connected. MAC Address of AP to be connected. (optional) Select the same security option with AP to be connected. © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
2.5. Serial to LAN(Wired and Wireless) Individual settings for serial #1 and serial #2 are possible. Set the serial parameters for serial to wireless (Ethernet) function. Set two channels (Main connection, Aux connection) for each serial port Setting management of Serial #1 and #2 (Main connection, Aux connection) 2.5.1. Main Connection settings Type Status Description Enable checked : Serial to LAN is used. Enable un-check: Serial to LAN is not used.
2.5.3. Packing Condition (Incoming serial data packing condition) Type Description Time Data packing until the set time and then sent to server after the set time. Size Data packing until the set size and then sent to the server. Character Inactivity Time: Data packing until the set character and then sent to the server. TCP/IP connection is discontinued if there is neither serial data nor network data during the set time. -. Enable/Disable the H/W CMD switch pin. H/W CMD switch -.
2.6. Firewall settings 2.6.1. DMZ Enable/Disable DMZ function. A DMZ allows a single computer on your LAN to expose ALL of its unused ports to the Internet. When doing this, the exposed computer is no longer behind the firewall. Sometimes TCP/IP applications require very specialized IP configurations that are difficult to set up or not supported by your router. In this case, placing your computer in the DMZ is the only way to get the application working.
2.6.2. Port forwarding When a computer on the internet sends data to the external IP address of the router (WizFi630A), the router (WizFi630A) needs to know what to do with the data. Port Forwarding simply tells the WizFi630A which computer on the local area network to send the data to. When you have port forwarding rules set up, your router takes the data off of the external IP address:port number and sends that data to an internal IP address:port number. Port Forwarding rules are created per port.
2.6.3. Packet filtering WizFi630A can accept or block Internet packets according to pre-defined MAC or IP address First, please do the basic settings Type Source MAC Dest IP Address Source IP Address Protocol Dest Port Range Source Port Range Action Description Pre-defined source MAC address for MAC filtering function Destination IP address Source IP address Supports TCP, UDP, ICMP Destination port range Source port range Enable/Disable MAC/IP/Port filtering function © Copyright 2015 WIZnet Co., Ltd.
2.6.4. Contents filtering Used to block certain websites (IP or domain names). Type Description Block all the websites whose domain is the input text URL Filter For example, if you input “sex”, the websites like www.sex.com is blocked. But www.sexgood.com is not blocked. If you would like to block all the websites whose domain name contains the input text, please use Host Filter function Block all the websites whose domain name contains the input text.
2.6.5. System Security Defense from external attack. Type Remote management Telnet management Description Settings about accessing methods from WAN to WizFi630A’s embedded web server Settings about accessing methods from WAN to WizFi630A’s telnet Ping from WAN Filter Disable/Enable the WizFi630A’s Ping response Broadcast Storm filter Block/Accept the Broadcast packets Block Port Scan Block WizFi630A’s port-scan function Block SYN Flood Block SYN flood © Copyright 2015 WIZnet Co., Ltd.
2.7. Managements 2.7.1. System Management Type Description Language Administrator Select language in the list Pre-defined ID/Password for webpage or Telnet login NTP (Network Time Set NTP server Protocol) Green AP Low power consumptive AP Once the DDNS server registers yours MAC address, your device can connect to the internet regardless of your address. DDNS service can be provided by DynDNS, freeDNS, zoneedit, no-ip. DDNS To use DynDNS, users should go to www.dyndns.
2.7.4. Port Setting Settings about wired port. In case of Gateway Mode, WAN port is set here In case of Gateway Mode, it is better to use the default WAN port number (Port #0) If you are not the administrator, we do not recommend changing this. Type WAN Port Description Select the WAN Port in case of Gateway Mode. Port #0 Enable / Disable Port #0. Port #1 Enable / Disable Port #1. Port #2 Enable / Disable Port #2. Port #3 Enable / Disable Port #3. Port #4 Enable / Disable Port #4. 2.7.5.
2.7.7. System Log The operation history of WizFi630A can be checked by using System Log. If the system log exceeds 24Kbyte, more recent log record is added. © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
3. Hardware Information 3.1. WizFi630A Pin Map No T Name 1 GND 2 3.3V 3 GND 4 3.
39 I/O, IPD EJT_TRSTN 40 I/O, IPD EJT_TMS 41 I/O, IPD EJT_TDI 42 I/O, IPD EJT_TCK 43 NC 44 NC 45 NC 46 NC GPIO21 UART2 Tx/Rx LED Serial Command Mode #1(GPIO19) GPIO18 UART1 Tx/Rx LED WPS LED(GPIO20) 47 I/O, IPD I2C_SCLK Serial Command Mode #2(GPIO2) 48 I/O, IPD I2C_SD RUN LED(GPIO1) 49 GND 50 3.3V 51 GND 52 3.3V Table 1. WizFi630A Pin Map © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
3.2. Dimensions © Copyright 2015 WIZnet Co., Ltd. All rights reserved.
4. Important Notice WIZnet reserves the right to make corrections, modifications, enhancements, improvements and other changes to its products and services at any time, and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders, and should verify that such information is current and complete. All products are sold subject to WIZnet’s terms and conditions of sale, supplied at the time of order acknowledgment.