WT-9002 IP65 G GS SM M IIn ntte errcco om m A An nd d A em m Acccce essss C Co on nttrro oll S Sy ysstte User Manual W R R R W T U A C O P O A T O N S D N B H D WIIIT TU UR RA AC CO OR RP PO OR RA AT TIIIO ON NS SD DN NB BH HD D
WT-9002 IP65 User Manual WT-9002 GSM INTERCOM AND ACCESS CONTROL SYSTEM INSTALLATION & WIRING DIAGRAM WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual Note: The call point must connect to the main unit with cables that are not exceeding 15 meters to avoid poor voice quality. The WT-9002 GSM Intercom works with any other single button intercom system of the gate station. To connect the call point to the WT-9002 unit please refer to the below wiring diagram. WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual GND Inputs and Outputs Wiring Connections WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual Note: If you require assistant on connecting the device to your Gate Controller don’t hesitate to contact us at http://www.witura.com/chat_room.html for technical support WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual CONTENTS 1. Introduction…………………………………………………………………………………………………………………………….7 2. WT-9002 IP65 Features………………………………………………………………………………………………………….7 3. Installation Instruction……………………………………………………………………………………………………………9 4. WT-9002 IP65 Programming Instructions…………………………………………………………………………….11 4.1 Description………………………………………………………………………………………………………………………………11 4.2 Programming the Administrator Numbers via Phone Call…………………………………………………….13 4.
WT-9002 IP65 User Manual 7. Additional Features…………………………………………………………………………………………………………………..45 8. Technical Specifications……………………………………………………………………………………………………………47 PACKAGE CONTENTS 1) 2) 3) 4) 5) 6) 7) 1.
WT-9002 IP65 User Manual Only Register User Can Open the Gate – Up to 1,000 authorized users When one of the 1,000 register users call to the WT 9002, the system will recognized the caller ID number (phone number) and open the gate automatically. Put Up A Simple Alarm System While You Not At Home The system have 2 input can connect to the motion sensor, magnetic door sensor or smoke, gas & glass break sensors. If any intruder or emergency happen, the WT 9002 units will SMS up to 3 telephone number.
WT-9002 IP65 User Manual IP 65 Enclosure The GSM unit is design fully protected against dust tight and protected against water jets from all directions. It is suitable to use at outdoor and complied to the International IP rating. 3. INSTALLATION INSTRUCTION Note: It is essential that you read the instructions fully prior to installing and programming the unit i) INSTALLING THE SIM CARD Note: Installing the SIM Card. Please be sure the initial 4 digit PIN code of SIM card is disabled.
WT-9002 IP65 User Manual iii) MEMORY The unit can be programmed up to 1000 phone numbers to become as authorized users. The system will respond or answer to the call of authorized users only and reject unauthorized calls. iv) OUTPUT The unit has 2 outputs which can be used as output. The outputs are connected to an on-board relay v) RELAYS There are 2 output relays which can be activated by the person called via the keypad on the mobile phone or landline phone.
WT-9002 IP65 User Manual vii) BACKUP BATTERY The unit has a rechargeable battery that powers the system for minimum of 8 hours in the event of a power outage. When the power is restored, it will recharge the battery automatically whenever the usage capacity fall below 9V. 4. WT-9002 IP65 PROGRAMMING INSTRUCTIONS 4.1 DESCRIPTION Note: As the WT-9002 IP65 can only be programmed by the 3 administrator numbers, you must first program those numbers into the unit.
WT-9002 IP65 User Manual When the system receives the programming message from the administrator, it will display a message icon on the top right corner of the screen as shown below… WT-9002 Message received After the programming message has been processed, the message icon will disappear and the system will shows “OK” indicate the setting has changed.
WT-9002 IP65 User Manual Guest WT-9002 4.2 PROGRAMMING THE ADMINISTRATOR NUMBERS VIA VOICE The administrator numbers can be program using the following prompts on the keypad and making the following three calls to the unit assuming the following 3 numbers are (1111558888), (2222669999), and (3333770000).
WT-9002 IP65 User Manual TEL: 1#, 2#, 3# TEL: 1# TEL: 1111558888 1# TEL: 4.3 OK PROGRAMMING THE ADMINISTRATOR NUMBER VIA SMS The first 3 SMS messages sent to the unit would be as the following assuming the 3 Administration numbers are (1111558888), (2222669999), and (3333770000).
WT-9002 IP65 User Manual Example of Return Message: TEL1=1111558888 TEL2=2222669999 TEL3=3333770000 4.4 READ THE PROGRAMMED ADMINISTRATOR NUMBERS VIA SMS It is possible to read all the programmed Administrator numbers by sending the following SMS to the unit. Send the following SMS Commands: *ADM?# Example of Return Message: TEL1: 1111558888 TEL2: 2222669999 TEL3: 3333770000 END 4.
WT-9002 IP65 User Manual Then input the current password 123456# (you should hear a short beep ~success) Continue to enter new password 654321# for 2 times (another short beep if password entered correctly) If the change has not been successful you will hear 3 beeps and must re-enter again. 4.6 CHANGING THE PASSWORD VIA SMS The system only allows the 3 administrators to change the 6 digits password.
WT-9002 IP65 User Manual After enter password… (Another short beep ~ Password Correct) Press *3# (you should hear a short beep ~ success) Continue press 1# to change the first administrator number (another short beep ~ success) Then enter the new administrator number 4444444444# (you will hear a short beep and the number has been changed to 4444444444 Continue...
WT-9002 IP65 User Manual Simply sends 3 SMS command as below: 1) *TEL1#4444444444 2) *TEL2#5555555555 3) *TEL3#6666666666 The system will replace the current administrator numbers with the new administrator numbers and will reply as follow Example of Returned Message: TEL1=4444444444 TEL2=5555555555 TEL3=6666666666 4.
WT-9002 IP65 User Manual And 2222222226 is programmed into list 6 Note: In the display screen of the unit, you should see as below. Guest: Continue input the guest number 2222222226 and ended with # Guest: 2222222226 And 2222222226 is programmed into list 6 4.11 PROGRAMMING THE GUEST LIST VIA SMS It is possible to program up to 1000 phone numbers to be authorized users in the white list of the unit and this can be done by sending SMS to the unit.
WT-9002 IP65 User Manual 4.12 PROGRAMMING THE GUEST LIST VIA LEARNING MODE It is possible to program the 1000 phone numbers into the Guest List via Learning Mode. To do this, you must first supply a 12VDC at Input 1 and turn on the unit as shown below. Once turn on the WT-9002 IP65, you shall see the following Settings: >>>> Search Wait… Input guest: 119 Timer Now the system is in learning mode. To program a phone number into the list, simply call the WT-9002 unit.
WT-9002 IP65 User Manual Input guest: 100 13544456666 Input guest: OK 13544456666 The number has programmed successfully. Note: If one of the list for example list 1 is full, the new incoming number with last digit number 1 will not program into the list and shall display as the following. Input guest: FULL 13544456666 4.13 REMOVE GUEST NUMBER FROM THE LIST To remove numbers from the list you would send the following SMS assuming you wish to remove the following number from the list.
WT-9002 IP65 User Manual 6666666667 WT-9002 >>>>>>>>>> WT-9002 >>>>>>>>>>>>>>>> WT-9002 Number Found Deleting the number Number deleted End WT-9002 To delete all numbers in the Guest List you would send the following SMS to the unit. Simply sends a SMS Command *DELB# to the unit and it will delete all programmed phone numbers in the list. Returned Message: Del-Book To permanently delete all numbers in the Guest List you would send the following SMS to the unit.
WT-9002 IP65 User Manual 4.14 RESTORE DELETED GUEST NUMBER It is possible to restore the deleted phone numbers of Guest List and this can be done by sending the following SMS to the unit. Simply sends a SMS Command *DARE#0 to the unit and it will restore the deleted phone numbers. In the display screen of the unit, you should see as below.
WT-9002 IP65 User Manual Relay 1 can also be activated via caller ID from any number that has been programmed in to the authorized user list or the administrators. Relay 2 can only be activated and controlled by the 3 administrator numbers as programmed in to the unit. 4.16 ACTIVATE RELAYS VIA SMS It is possible to activate the relays to latch for 1 second at factory default by sending the below SMS command.
WT-9002 IP65 User Manual Relay 1 will now latch for 10 seconds every time it is activated (*0#) via handset, Caller ID or SMS command (*ECL1#) Relay 2 will now latch for 60 seconds every time it is activated (*1#) via handset or SMS command (*ECL2#) When relay 1 latches, the unit will display the counter on the LCD as shown. 00008 EXT WT-9002 When both relays latched… 00006 EXT 4.
WT-9002 IP65 User Manual Press *6# (A short beep ~ success) Continue press 2# for relay 2 (A short beep ~ success) Then input value 00120# (A short beep ~ success) Relay 2 will now latch for 120 seconds and after 120 seconds it will switch off and sends a message back to the administrator informed that Relay 2 has closed. Returned Message: RLY2-OFF When relay 1 latches, the unit will display the counter on the LCD.
WT-9002 IP65 User Manual Simply send the 2 SMS command as below: *RLY1#00060 *RLY2#00180 Example of Returned Message: RELAY1=00060 RELAY2=00180 4.20 LATCHES THE RELAYS TO STAY ON It is possible to activate the relays to stay on by sending the below SMS command. The relays will stay ON until the switch OFF command is issued.
WT-9002 IP65 User Manual 4.21 DISPLAY PROGRAMMED ADMINISTRATOR NUMBER To view the actual admin numbers programmed in you would just call the unit and prompt the following to view all 3 numbers.
WT-9002 IP65 User Manual Example of sending the below command: *RERN#100 (Factory Default) Only Administrator number 1# will receive a report message after setup Returned Message: RERN:<100> *RERN#110 Administrator number 1# and 2# will receive a report message after setup Returned Message: RERN:<110> *RERN#111 All the Administrators will receive a report message after setup Returned Message: RERN:<111> Sending the below command will turn Off this feature: *RERN#000 4.
WT-9002 IP65 User Manual 4.25 AC POWER ON/OFF ALERT MESSAGING The unit is able to send alert message to the administrator in the event the main power is out / turned off. When the main power is restored it can notify the administrator again the main power is on. When main power OFF The unit will send a message: ACP-OFF Note: At the same time, it will send an ALWAYS high pulse out from I/O port. Alarm will sound. When main power restored The unit will send a message: ACP-ON 4.
WT-9002 IP65 User Manual Example of Returned Message: MIC0:<5> 4.28 ADJUSTING THE RINGING TIME WHEN THE SYSTEM MAKING A CALL This is the function that determines how many rings the unit will allow before the system will move on to the next number. This command will then apply for all 3 numbers. (Default: 20 seconds, maximum 60 seconds) Example: Adjust the ringing time to 15 seconds Example: Sending the following SMS Command: *TETI#15 Example of Returned Message: TETI:<15> 4.
WT-9002 IP65 User Manual Returned Message: ALAC-OFF 4.30 SETTING THE ALARM TIME VALUE It is possible to set the alarm time up to maximum value of 65535 seconds by sending the following SMS command to the unit. (Default Value: 600) Example sending the following SMS Command: *ALTM#00060 – The alarm will sound for 60 seconds every time it triggered Example of Returned Message: ALTM:<00060> 4.
WT-9002 IP65 User Manual Warning: User can use their preset password to reset the unit and it must be noted down or remembered. In case if the password is forgotten or cannot be accessed, please consult our technical department. To manually reset the unit, you can press and hold on the “Call” button and turn on the unit for 10 seconds. The unit will displays Wait… and then OK, the unit is reset. 4.
WT-9002 IP65 User Manual WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual 5. WT-9002 Programming Via PC Installing the Software Step 1: Insert the provided WT-9002 CD into your computer. You will find a folder named “WT-9002 Programmer”. Step 2: Inside this folder you will find “WT-9002 Setting” file, you might want to copy this file into your computer. It is an executable program that does not require installation.
WT-9002 IP65 User Manual Note: Make sure the WT-9002 device is connected to your PC COM Port with the provided programming serial cable before begin programming. Step 5: Understanding the WT-9002 Programmer interface. Press here for Serial Port Setting Download all settings from the WT-9002 device Upload all settings to the connected WT-9002 device Checking software version WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual Select the COM Port that WT9002 device has connected to Leave this section unchanged Establish connection with the WT-9002 device. Press this button when COM Port is selected. Programming the Administrator Numbers 1 – 3 *TEL[N]# Note: It is possible to program up to maximum of 16 digits for each administrator number. Programming the Guest list - *BOOK# WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual Enter phone number here to be programmed as Guest Press Add to save You can also import a list of phone number from an Excel file. But be sure that all the phone numbers are entered in the first column as shown below. WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual Access Control for Administrators *ANY?# Adjust the ringing time *TETI# Default: 20 seconds, maximum 60 seconds Turn ON/OFF the function of Input 1 *CTR1# Turn ON/OFF the function of Input 2 *CTR2# Setting the feature of Input 1 - *CTC1# Setting the feature of Input 2 - *CTC2# WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual Setting the Counter Alert Value of Input 1 *COA1# Setting the Counter Alert Value of Input 2 *COA2# Note: You are able to program the Counter Alert Value up to a maximum of 65535 only Turn ON/OFF Audible Siren function when Input 1 triggered *ALM1# Turn ON/OFF Audible Siren function when Input 2 triggered *ALM2# Setting the 6-digits Password for Reset Command - *PAWO# Setting Automatic Mode or Password Mode Turn ON/OFF Power Failure Alarm function *ALAC# Setting the Alarm Tim
WT-9002 IP65 User Manual Reset Input 1 SubCounter *CLC1# These values will be read from the WT-9002 device when pressed the upload button Reset Input 2 SubCounter *CLC2# Reset Input 1 Total-Counter *CLA1# Reset Input 2 Total-Counter *CLA2# Adjust the Microphone volume *MIC0# Adjust the Speaker volume *SOUD# Extending the latching time of relay 1 *EXT1# Extending the latching time of relay 2 *EXT2# Download all the Settings from the WT-9002 Device Step 6: Download all the settings from the WT-9002 devic
WT-9002 IP65 User Manual On the WT-9002 programmer software, you may notice that the “Upload” and “Download” button become visible. Now you may click on the “Download” button to download all the settings from WT-9002 device. Upload all the Settings to the WT-9002 Device Step 6: Upload all the settings to the WT-9002. To start programming all the settings, simply press the “Upload” button. WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual To logout the programmer software, simply click the X button on the top right. WT-9002 IP65 – USER MANUAL – Rev.2.0 – Technical Support: technical@witura.
WT-9002 IP65 User Manual 6.
WT-9002 IP65 User Manual 7. ADDITIONAL FEATURES: Input Counters Inputs Alarm These inputs can be programmed to count active high pulses. It needs to be activated by SMS to start counting. These inputs can be programmed by SMS to alarm when it triggered.
WT-9002 IP65 User Manual Multi-features Inputs These inputs can be programmed to behave differently, it can count input active high pulses, generate an alarm or activate relays. It needs to be activated first by SMS to start using the commands. Function Command for Input 1 - *CTC1#X Function Command for Input 2 - *CTC2#X X stands for Functions No. 1 – 8 Function No. 1 (Default) - Count whenever it receives active high pulses Function No.
WT-9002 IP65 User Manual 8. TECHNICAL SPECIFICATIONS Built in power supply 15 Volts 1 Amps and fused 2 amps. Dual Band (900/1800Mhz) or Quad Band Module (850/900/1800/1900Mhz) Power Supply: 100VAC ~ 250VAC Operating Temperature - 25 to 55°C Humidity Less than 95% RH. Lightning Protector: 3-5W 2 Output relays normally open 240 volts 1 amp. Can call up to 3 numbers outbound. Battery back-up for up to 8 hours. Caller ID for up to 1000 users.