WT-368 C CD DM MA AF Fiix xe ed dW Wiirre elle essss P Ph ho on ne e User Manual W R R R W T U A C O P O A T O N S D N B H D WIIIT TU UR RA AC CO OR RP PO OR RA AT TIIIO ON NS SD DN NB BH HD D
WT-368 CDMA Phone KEY TECHNICAL SPECIFICATIONS Following are the key technical specifications of this Phone: 1. Networks support: CDMA800MHz 2. Frequency range: Transmits: 824~849MHz, Receives: 869~894MHz 3. Voltage: DC12V 4. Built-in CDMA 2000 1x Industrial Module 5. Support IS95A/B and CDMA 20001X 6. Stand by hours: 48 Hours 7. Talk time: 2-6 Hours 8. Charging time: 6 hours 9. Power consumption: Static ≤25MA, Emission ≤500MA 10. Peak power consumption: 0.25W/0.5W 11.
WT-368 CDMA Phone KEY FUNCTIONS The key functions of the Phone are list as below: 1. Multicolor backlight display (e.g.: blue, green) 2. Can dial the local calls, mobile calls, international calls and special free calls 3. Incoming number and call out number Bar and unbar 4. No need to dial area code when calling local numbers (Area Code Preset) 5. Automatically connects to IP network when dialing long distance (optional) 6. The 12 chords music optional 7. Caller ID and Hand free enable 8.
WT-368 CDMA Phone CAUTIONS AND STORAGE Cautions: 1. This wireless Phone should not be used at garage, oil storage, and chemical plant or near to any inflammable or explosive substance. 2. This wireless Phone should be avoided in the hospital. It will interfere with medical electronic equipments such as pacemaker and audiphones. 3. If it is found that the wireless Phone is not successful in login onto network, please check whether the SIM card or antenna is well installed. 4.
WT-368 CDMA Phone I. Pre-Code Setting You can preset 5 groups’ pre-codes for your wireless Phone The pre-code can be 5 digits to 15 digits. For this pre-code, you can dial some special number directly. You can make this setting as below: i) Press the “Setting” key.
WT-368 CDMA Phone i) Press the “Setting” key. ii) Input “080#”. IV. Incoming call blocks and unblock If you do not want anybody to disturb you or call back, then you can block and unblock the incoming calls with your wireless Phone You can block the incoming call in this way: i) Press the “Setting” key ii) Input “051#” Then none can call you back but you can call others freely.
WT-368 CDMA Phone Malfunction Reasons 1. Can not make the call A. The antenna disengage; B. No signal or the signal is too weak C. Your Phone is out of charge 2. No sound when the call comes A. The loudspeaker was damaged. B. The handle placed in a wrong potion 3. EAA4 display on LCD The SIM card was locked, input the PIN code or change another SIM card 4. EAA5 display on LCD A. The SIM Card is installed incorrectly. B. The SIM Card was damaged. 5. EAA6 display on LCD Net was locked.
WT-368 CDMA Phone You should write a number for your FWP before you using all of the functions on your FWP. You can operate it like this as below: 1. Open the AnyDataESN Software 2. Connect the computer with the data cable i) Turn on the power supply of wireless phone. You can see the power supply switch at the back of the wireless phone. ii) Connect the phone and the computer with the data cable. Notice: Make sure that the handset is out of the phone during you write the number for your phone.
WT-368 CDMA Phone “SIO-DM” key, then the phone will connect the software automatically. Then you will see picture as below in Picture 1.1 Picture 1.1 If the connecting is OK, then you can see the picture as below in Picture 1.2 Picture 1.2 If the connecting is unsuccessful, then you will see the picture in Picture 1.3. And WT-368 – USER MANUAL – Rev.1 – Technical Support: technical@witura.
WT-368 CDMA Phone you should reboot the phone and try it again. Picture 1.3 5. Press “Read ®” key, then the wireless phone will read information automatically, and then you can see the Picture 1.4 as below: Picture 1.4 If the read is successful, you can see “Picture 1.5” as below. And then you should WT-368 – USER MANUAL – Rev.1 – Technical Support: technical@witura.
WT-368 CDMA Phone input the IMSI code (at least 15 digits), SID code (at least 5 digits), NID code (at least 5 digits), Pri-CHA and Pri-CHB code (three digits), Sec-CHA and Sec-CHB (three digits) and ESN code (at least 8 digits) for your wireless phone. Your Networks Provider will offer there codes to you. You can take an example as Picture 1.5 as below: Picture 1.5 6. After you writing the data for the wireless phone. Please press the “Write (W)” key.
WT-368 CDMA Phone Picture 1.7 7. Exit Number writing program You can exit this program if the wireless phone written the number successfully. You can exit this program by pressing the “Exit” key 8. Pull out the data cable and turn off the power supply. Then reboot the wireless phone and you can use the wireless phone now. WT-368 – USER MANUAL – Rev.1 – Technical Support: technical@witura.