WT-1010C2 G GS SM MA ALLA AR RM MS SY YS ST TE EM M User Manual W R R R W A C O P O A T T U O N S D N B H D WIIIT TU UR RA AC CO OR RP PO OR RA AT TIIIO ON NS SD DN NB BH HD D
WT-1010C2 USER MANUAL Contents 1. Getting Started ……………………………………………………………………………………………………………………………………………………4 1.1 In the Packaging………………………………………………………………………………………………………………………………………….4 1.2 Viewing the WT-1010C2……………………………………………………………………………………………………………………………..4 2. Introduction to WT-1010C2 GSM Alarm System…………………………………………………………………………………………………5 2.1 General Overview………………………………………………………………………………………………………………………………………….5 3. Main Features of the WT-1010C2…………………………………………………………………………………………………………………………6 4.
WT-1010C2 USER MANUAL Step 12.3 Enable/Disable the Function of Activate Output Relay 2 when GSM Tower Failure………………………………………………………………………………………………………………………25 Step 12.4 Setting the Parameter for GSM Tower Failure………………………………………………………25 Step13- Input Settings………………………………………………………………………………………………………………………………26 Step14- Arm and Disarm the System (via Fixed Line Phone)…………………………………………………………………27 Step15- Setting the Automatic Call Answering Feature…………………………………………………………………………28 6.
WT-1010C2 USER MANUAL 1. Getting Started 1.1 In the Packaging Please make sure the following items are included in the packaging: Quantity Name WT-1010C2 Main Unit Telephone line DB15 (F) cable Power adapter 5m GSM terminal antenna User’s Manual 1 1 1 1 1 1 Unit set set set set set CD 1.
WT-1010C2 USER MANUAL 2. Introduction to the WT-1010C2 GSM Alarm System The WT 1010C2 GSM Terminal is a wireless communicator for alarm and fire panels that uses the cell phone network (GSM) to transmit alarms and other panel event. The module checks the status of the PSTN line and in case the PSTN line becomes unavailable, the WT 1010C2 GSM emulate the line signal to the panel.
WT-1010C2 USER MANUAL 3. Main Features of the WT-1010C2 1. Panel compatibility - Allows any contact ID alarm panel to transmit alarms over GSM using the GSM voice channel 2. Works over the GSM cell phone networks Units can be used wherever there is cell phone coverage 3. Telephone line backup: WT-1010C2 give priority to the lowest cost network. WT1010C2 uses the telephone line as the main transmission line and uses the GSM voice channel as backup 4.
WT-1010C2 USER MANUAL 7. It is possible to arm/disarm the unit remotely via remote control, SMS or phone call. Alternatively, it also can connect to the basic telephone to perform arm/disarm. 8. Three digital inputs: The system has the function to send SMS and call to the user in the event of input triggered.
WT-1010C2 USER MANUAL 4. Installation Instructions Note: It is essential that you read the step by step instructions fully prior to installing and programming the unit 4.
WT-1010C2 USER MANUAL 4.3 Wiring Diagram B (View of DB-15 Cable Connector Female Type) Attention: The color coding on the above indicators will be identical with the actual DB15 connector cable (Female Type) 4.4 Description 1. Antenna: connect the antenna to the GSM module; place the antenna as far as possible from the WT-1010C2 and do not leave any coiling of the antenna cable to avoid radiant interference 2.
WT-1010C2 USER MANUAL 4.5 WT-1010C2 Inputs and Outputs Wiring Instructions RLY1 (OUT1), RLY2 (OUT2), RLY3 (OUT3) Remote Controlling Outputs These open collector outputs can be turned on and off remotely through a SMS. Remote control will be reachable by sending a SMS with a certain command. Note: When sending normal SMS with command below, the WT-1010C2 will turn On / Off the output relay and reply a message of output has turned On / Off to a programmable phone numbers.
WT-1010C2 USER MANUAL Inputs & Outputs Wiring Diagram (View from DB-15 Connector Cable Female Type) Permanent +V Output Facility There is a permanent +V output when the WT-1010C2 is power on. This output is available on the connection PIN8 and ground on the main board. The output voltage is according to power supply used on WT-1010C2. It can be used to power on other facility or device. 4.6 Installing the SIM Card Note: Installing the SIM Card.
WT-1010C2 USER MANUAL 4.7 Power up the WT-1010C2 When power up the WT-1010C2, it will display as below LOADING :>>>>> WAITING… When the terminal is ready to use, it will display as below Power Signal WT-1010 Battery Note: Whenever the WT-1010C2 fails to logon to network or fails to detect the SIM card, it will restart automatically until it has detected the SIM card or successfully logon to network. 4.
WT-1010C2 USER MANUAL Note: Some telephone sets are sensitive to the GSM radio signal. For this reason you may hear a characteristic noise in the telephone receiver when calling. If the noise is disturbing, change the location of the phone set (try to keep it as far as possible from the WT-1010C2 unit antenna). Usually it is possible to find a suitable location for the phone with minimal level of interference. 5. WT-1010C2 Configuration Instructions (Via Fixed Line Phone) 5.
WT-1010C2 USER MANUAL ENTER SETTING… OK Password entered correctly HAND FREE… Programming Mode Step 2. Reset the WT-1010C2 Unit To reset the unit, you can press *15* to proceed. REST ON&OFF: REST ON&OFF: 1 Then press 1# to reset REST ON&OFF: 1 OK Note: It is advised that you should reset the WT-1010C2 unit before proceeding to the below programming section Step 3.
WT-1010C2 USER MANUAL TEL: 13232353646 1# Enter administrator number 13232353646 for example and ended with # TEL: OK Number has programmed successfully You may continue to program administrator number 2, 3, 4, 5, 6, 7 and 8 by pressing *2* , *3* , *4* , *5* , *6* , *7* , *8* Step 4. Setting the Recipient that will receive Alert Messages The unit can send text alerts to 1 or all 8 of the programmed administrator’s numbers. To do this setting, you can press *18* to proceed.
WT-1010C2 USER MANUAL Step 5. Programming the Area Code To program area code, you can press *9* to proceed. NEW AREA: NEW AREA: 03 Enter area code 03 for example and ended with # NEW AREA: 03 OK Area code has programmed successfully Note: It is possible to program up to 4 digits Step 6. Setting the Function of Adding Area Code when Transmitting an Alarm To turn on/off this function, you can press *14* to proceed.
WT-1010C2 USER MANUAL Step 7. Setting the Delay Time for Transmitting a Dialing Number To set the delay time, you can press *34* to proceed. DTTRANSMIT: DTTRANSMIT: 07 Example: To set the required delay time at 7 seconds Simply press 07# DTTRANSMIT: 07 OK Note: The Delay Time is a 5 digits value range from 00 – 59 seconds (Default: 04 seconds) Step 8.
WT-1010C2 USER MANUAL Step 9. Setting for Auto Test Step 9.1 Time Setting To setup time, you can press *16* to proceed. TIME: : : TIME: 08 : 30 : 00 Example: To set the time at 8.30am Simply input digits and ended with # TIME: 08 : 30 : 00 OK Step 9.2 Setting the Auto Test Report Time Section 1 The system has the function of sending the test report to the central station at the programmable time section. The time is entered in 24 Hour format.
WT-1010C2 USER MANUAL Step 9.3 Setting the Auto Test Report Time Section 2 The system has the function of sending the test report to the Administrator at the programmable time section. The time is entered in 24 Hour format. To program the auto test report time section 2, you can press *42* to proceed. DSTM2: : : DSTM2: 18 : 00 : 00 Example: To set the auto test report time at 18.00pm Simply input digits and ended with # DSTM2: 18 : 00 : 00 OK Note: Skip this setting if only 1 time section is needed.
WT-1010C2 USER MANUAL Note: Skip this setting if only 1 time section is needed. Step 9.5 Enable/Disable the function of dialing the programmed Administrator number for Auto Test To turn on this function, you can press *27* to proceed. DTIMEC ON&&OFF: DTIMEC ON&&OFF: 1 To turn on this function simply press 1# To turn off this function simply press 0# DTIMEC ON&&OFF: 1 OK Default Value: 0 Step 9.
WT-1010C2 USER MANUAL Note: Please refer to programming instructions via SMS for editing the message content of Auto Test Step 9.7 Setting the Burst On and Burst Off time of DTMF tones The Burst ON and Burst OFF timing of the sending Contact-ID can be adjust with the below command. To set the Burst on and Burst off time press *37* to proceed.
WT-1010C2 USER MANUAL Step 10. Setting for PSTN Failure To turn on this function, you can press *30* to proceed. PST: ME: CA1: OU: CA2: PST: ME: 1 OU: 1 CA: 1 AL: AL: 1 CA2: 1 Example: Setting the unit to generate an Alert Message, call the administrators, generate a pulse (+V) and sound the audible alarm when PSTN failed. Simply input 11111# PST: ME: 1 OU: 1 CA: 1 CA2: 1 AL: 1 OK Description: “ME” stands for generation of SMS when PSTN failed.
WT-1010C2 USER MANUAL Note: PSTN Failure Output facility can be used on alarm panel for alert notification Step 11. Setting for AC Failure To turn on this function, you can press *31* to proceed. ADC: ME: CA1: AL: CA2: ADC: ME: 1 AL: 1 CA1: 1 CA2: 1 Example: Setting the unit to generate an Alert Message, call the administrators, generate a pulse (+V) and sound the audible alarm when AC failed.
WT-1010C2 USER MANUAL Note: Power Down Output facility can be used on alarm panel for alert notification Step 12. Setting for Overcoming GSM Jammers & GSM Tower Failure Step 12.1 Enable/Disable the function of Activate Output Relay 1 when GSM Jammers is detected To turn on this function, you can press *38* to proceed. NETWORK ON&&OFF: NETWORK ON&&OFF: 1 To turn on this function simply press 1# To turn off this function simply press 0# NETWORK ON&&OFF: 1 OK Step 12.
WT-1010C2 USER MANUAL NETDT1: 05 RLY1: 05 Example: To set the network failure time for 5 seconds and the turn on time of Relay 1 for 5 seconds Simply press 0505# NETDT1: 05 RLY1: 05 OK Description: “NETDT1” stands for network failure time range from 00 – 59 seconds. Default: 6 seconds. “RLY1” stands for turn on time of Relay 1 when network fails (00 – 59 seconds), 00 means RLY1 will stay ON permanently. Step 12.
WT-1010C2 USER MANUAL NETDT2: RLY2: NETDT2: 06 RLY2: 10 Example: To set the network failure time for 6 seconds and the turn on time of Relay 2 for 10 seconds Simply press 0610# NETDT2: 06 RLY2: 10 OK Description: “NETDT2” stands for network failure time range from 00 – 59 seconds. Default: 6 seconds. “RLY2” stands for turn on time of Relay 2 when network fails (00 – 59 seconds), 00 means RLY2 will stay ON permanently. Step 13.
WT-1010C2 USER MANUAL Description: “OP” stands for generation of SMS when input triggered (Open). Default: 0 “CL” stands for generation of SMS when input triggered (Close). Default: 0 “AL” stands for sounding the audible alarm when input triggered. Default: 0 “CA1” stands for calling the administrators when input triggered (open). Default: 0 “CA2” stands for calling the administrators when input triggered (close).
WT-1010C2 USER MANUAL To acknowledge the above alarms simply press the below command on your phone and the system will stop calling you. *123456# (Default password: 123456) Step 15. Setting the Automatic Call Answering Feature The WT-1010C2 can be programmed to answer all incoming calls automatically even there is no fixed line phone attached to it. When the call is answered, it allows the owner to arm or disarm the system by entering a command from their phone’s keypad.
WT-1010C2 USER MANUAL 6. WT-1010C2 Programming Instructions (Via SMS) Programming the WT-1010C2 can also be done via SMS commands using your phone. Any programming command sent by SMS must be in CAPITAL letters. The fields between square brackets are parameters; do NOT enter the square brackets. When you send a command, you will receive the answer for the first time even if your GSM number is not in the administrator list.
WT-1010C2 USER MANUAL XXXX stands for Account Number (Can be set up to 50 digits) Example: To set an account number 9999 into the system, you would send the following SMS message to the unit. *ACCT#9999 Return Message ATACC:9999 Note: For Contact-ID Protocol details please refer to www.smartelectron.ru/files/DC-05_ Contact_ID.pdf 6.3 Editing the Message Contents of Auto Test (Up to 50 Characters) The message contents can be edited and programmed up to 50 characters.
WT-1010C2 USER MANUAL N stands for Input number 1 – 3 XXXXXX… stands for alert message content Example: If you want the alert message to display “Garage Opened!” when input 1 triggered; you would send the following SMS message to the unit. *USE1#Garage Opened! Return Message USE1=Garage Opened! 6.5 Editing the Inputs Alert Messages (When No Pulse) The Input Alert Message can be edited and programmed up to 50 characters.
WT-1010C2 USER MANUAL Text Command: *RLY[N]#XXXXX N stands for Output number 1 - 3 XXXXX stands for 5 digits value: The number of seconds (00000-99999) For example, assume you want to turn on the output relay number 2 for 1 hour, you would send the following SMS message to the unit. *RLY2#03600 Return Message *RLY2#=03600 Sending the following SMS Message to unit would mean turn off the output relay number 1. *RLY1#00000 6.6.
WT-1010C2 USER MANUAL 6.7 Arm and Disarm the System (Via SMS) It is possible to arm and disarm the system by SMS. You can send the following text command to unit. Text Command: *DARM#X X stands for ON (1) or OFF (0) value Example: To arm the system, you can send the following text message to the unit. *DARM#1 Return Message ARM To disarm the system, you can send the following text message to the unit. *DARM#0 Return Message DISARM WT-1010C2 – USER MANUAL – Rev.3.9 – Technical Support: Technical@witura.
WT-1010C2 USER MANUAL 7. Miscellaneous Settings 7.1 Inquire All Programmed Administrator via Voice To inquire all administrator numbers, you can press *32* to proceed. ADMIN: 1: 1234567890 All the administrator numbers will be displayed in sequence 7.2 Deleting the Administrator Number via Voice Example: To delete the programmed administrator number 1, you can press *1* to proceed. TEL: 1# TEL: 1# Simply press # to delete DEL1: OK 7.
WT-1010C2 USER MANUAL NEW PASSWORD: NEW PASSWORD: 654321 Input new password and ended with # NEW PASSWORD: 654321 OK 7.4 Inquire the status of the Recipients that will receive Alert Messages via Voice To inquire the status of the recipients, you can press *19* to proceed. RECIPIENTS: 11111111 The status will be displayed on screen Press # to turn back 7.5 Checking the Signal Strength via Voice To check the signal strength, you can press *20* to proceed.
WT-1010C2 USER MANUAL WAIT TIME: WAIT TIME: 20 Example: To set the waiting time for 20 seconds Simply input 20 and ended with # WAIT TIME: 20 OK Note: The waiting time is a 2 digits value range from 20 – 59 seconds (Default: 30 seconds) 7.7 Setting Arm Delay Time (Input 1 Only) Input 1 can be programmed to arm after a preset time when the Arm button is pressed or Arm function is activated by fixed line phone. To program the delay time, you can press *45* to proceed.
WT-1010C2 USER MANUAL 7.8 Enable/Disable System Power Up SMS Notification The system is able to generate SMS notification whenever the WT-1010C2 is turned on. To enable this function, you can press *46* to proceed. POWER UP MSG ON&&OFF: POWER UP MSG ON&&OFF: 1 To enable this function simply press 1# To disable this function simply press 0# POWER UP MSG ON&&OFF: 1 OK Default Value: 0 7.
WT-1010C2 USER MANUAL 7.10 Activate Output Relay to stay on for a specific time via Voice To activate output relay 1 to stay on for a specific time, you can press *21* to proceed.
WT-1010C2 USER MANUAL 7.12 Setting the WT-1010C2 to ignore the front dialing digits when dialing the Administrator via Voice This function is useful when the WT-1010C2 is connected to the PABX system where Access Digits are required for Extension Line/Centrex Line. To set the unit to ignore the front dialing digits, you can press *44* to proceed. DEL-NUM: DEL-NUM: 2 Example: To set the unit to ignore first 2 dialing digits Simply press 2# DEL-NUM: 2 OK Note: The value is 0 – 4 (Default: 0) 7.
WT-1010C2 USER MANUAL Note: Both SPK and MIC volume level range from 1 – 4 (Default: 1). Adjust the speaker and microphone volume to compatible with your alarm panel 7.14 Inquire the Software and Hardware Version of WT-1010C2 via Voice To check the software and hardware version of WT-1010C2 unit, you can press *13* to proceed. HW: 1.1ver SW: 1.0 ver MW: 1.5ver The information will be displayed on screen Press # to turn back 7.
WT-1010C2 USER MANUAL Example of Return Message CSQ=<28> 7.17 Checking the Current Time Status via SMS To check the current time, you can send the following SMS command to the unit. Text Command: *ASTM# Example of Return Message TIME-01:35:50 7.18 Changing the Programming Mode Password via SMS It is possible to change the login password by sending the following SMS command.
WT-1010C2 USER MANUAL Return Message REST-OK 7.20 Inquire the Status of Inputs, PSTN and AC To inquire the status of inputs, PSTN and AC, you can send the following SMS command to the unit. Text Command: *CTC?# Example of Return Message AC: 1 AC Available PSTN: 0 INPUT1: 0 PSTN Unavailable INPUT2: 1 Input 1 normal INPUT3: 0 Input 2 triggered Input 3 normal 8. Technical Specifications 1. Environment temperature: 0~+50℃ 2. Relative humidity: 10%~95% 3. Air pressure: 86~106kpa 4.
WT-1010C2 USER MANUAL Warranty Witura Corporation Sdn Bhd guarantees all WT-1010C2 GSM Fixed Wireless Terminal against defective parts and workmanship. Witura Corporation Sdn Bhd shall, at its option, repair or replace the defective equipment upon the return of such equipment to any Witura branch.