WLAN 802.11a+b+g Mini-PCI Module Model EM-500AG OEM Installation Manual 1.The OEM integrator couldn’t provide any information to end user regarding how to remove or install the device. 2.The module is sold only to the OEM integrators & the manual is valid only for the OEM manufactures. 3. Changes or modifications to this equipment not expressly approved by WNC may void the user’s authority to operate this equipment. Version: 1.
Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows™ 98SE/2000/ME/XP are trademarks of Microsoft ® Corp. Pentium is trademark of Intel. All copyright reserved.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents 1. INTRODUCTION 4 1.1 THE WLAN 802.11 A+B+ G MINI-PCI M ODULE .....................................................4 1.2 HARDWARE INSTALLATION & ANTENNA INFORMATION 2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 4 9 2.1 INSTALLATION .........................................................................................................9 2.1.1 ADDITIONAL S ETUP P ROCESSES ...........................................................................12 2.1.2 VERIFYING THE DRIVER ........
1. Introduction 1.1 The WLAN 802.11a+b+g mini-PCI Module Thank you for purchasing the WLAN a+b+g mini-PCI Module that provides the easiest way to wireless networking. This Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. 1.2 Hardware Installation & Antenna Information l Module is installed in the Personal Computer, located either under the keypad or on the bottom side of the Personal Computer (see the following diagrams).
l Antennas are embedded in the two sides of the panel (see the two antennas shown below) Only the DT3 antenna can be used. Important Note: This module is restricted to mobile configuration. The antennas of module should be installed and operated with minimum distance 20cm between the radiator and all persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The module is for OEM installation only and can not be sold to end user directly.
*Caution !! (1). This module cannot be bound in a tablet computer for RF exposure issues. (See label 1) (2). Due to the RF exposure issues, this module can be used in a laptop computer in normal operation, but cannot be used when it is put above the lap and the LCD screen is in the closed position.
(3). This module must be labeled with FCC ID. (See label 3) Label 3 (4). If the FCC ID is not visible when the module is installed inside another device, then the outside of device must also display a label referring to the enclosed module. The exterior label can be “ Contains Transmitter Module FCC ID: NKREM500AG” or similar wording.
Label 4 Please put Label 2 & Label 4 to the enclosure of end product to note the end user. (5). The user manual for end users must include the following information in a prominent location. “ IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
2. Driver/Utility Installation / Uninstallation 2.1 Installation Note! The Installation Section in this User Manual describes the first-time installation for Windows. To re-install the driver, please first uninstall the previously installed driver. See Chapter 2.2 “Uninstallation” section in this User Manual. Follow the steps below to complete the driver/utility installation: 1. Insert the Installation Software CD into the CD-Rom Drive. 2. Click “Next”.
3. Read the License Agreement and click “Yes”. 4. Click “Next” to continue or click “Browse” to choose a destination folder. 5. Click “Next”.
6. Click “Yes” to create a shortcut icon on your desktop. 7. Click “Finish”. 8. You should now see the shortcut icon on your desktop.
2.1.1 Additional Setup Processes During software installation procedure, each operating system may prompt different specific options: 1. Windows 98SE: The system will request the original Windows CD during the installation process. When the installation is finished, you’ll have to restart your computer. 2. Windows Me: Please restart your computer when the installation is finished. 3.
3. Windows XP: Step 1. Click Start>Control Panel> System. Step 2. Select “Hardware” tab, and click “Device Manager”. Open “Network adapters”. You should see your WLAN a+b+g mini-PCI Module in the list. Right-click this Adapter and choose “Properties”. Step 3. From the “Device status”, you should see the line “This device is working properly”. If, instead, you see error messages displayed, please uninstall this Adapter (right-click this Adapter from the “Network adapters” list and choose “Uninstall”).
2.2 Uninstallation Note! Before uninstallation, please close all running programs. 1. Click Start>Programs>WLAN a+b+g mini-PCI Module>UnInstall WLAN a+b+g mini-PCI Module. 2. Choose “Remove”. Click “Next”. 3. Click “OK” to start Uninstall. 4. Click “Finish”. Uninstall is now completed.
3. Connecting to an Existing Network 1. Double click the shortcut icon of “WLAN a+b+g mini-PCI Module” on the desktop, and the “WLAN a+b+g mini-PCI Module Configuration” window will appear. 2. Click “Refresh” button , and all available networks will be listed.
3. From the list of “Available Networks”, choose one network by double clicking the Network Name . One of the following dialog boxes appears. Click “Yes” to continue. 4. If the WEP of the chosen network is enabled, the “Security Setting” tab is displayed. Enter the correct Encryption Keys and click “OK”. You need to contact the network administrator for the values the Encryption Keys. 8.
3.1 Additional Note for Windows XP In Windows XP, it is recommended that you use the WLAN a+b+g mini-PCI Module Configuration Utility. Before using the Utility, please follow the steps below to disable the Windows XP Zero Configuration: Option 1: 1. Double click the shortcut icon to open the Utility. 2. From the Windows System Tray, you should see the signal icon. Right-click it and select “Disable Zero-Configuration”. Option 2: 1. Go to “Control Panel” and double click “Network Connections”. 2.
4. Creating a New Network 1. In “WLAN a+b+g mini-PCI Module Configuration” window, click “New” 2. Select the “Profile Editor” tab and check the check box of “Enable Advanced Setting” to edit all settings. Click “OK” to save the settings. 18 ..
3. Click the “Security Setting” tab and set the Encryption Keys. Click “OK” to save the settings. When you are creating an Infrastructure mode and IEEE802.11b standard network, please enter a passkey in “Shared Keys: First” field. For Infrastructure mode and IEEE802.11a standard network, you may enter a passkey in either “Unique Key” field or “Shared Keys: First” field. If you are creating an Ad-Hoc mode network, enter a passkey in “Shared Keys: First” field. 4.
5. Configuration 5.1 Device Configuration You can set the Wireless Network Adapter to work in either “infrastructure” mode or “ad hoc” mode. Infrastructure Mode In infrastructure mode, devices communicate with each other by first going through an Access Point (AP). Wireless devices can communicate with each other or can communicate with a wired network. When one AP is connected to wired network and a set of wireless stations, it is referred to as a BSS (Basic Service Set).
5.1.1 Non-Default Settings Configuration 1. Open “WLAN a+b+g mini-PCI Module Configuration” by double clicking the shortcut icon on the desktop. Note! If there’s no network name listed in the “Profile List”, click “Refresh” button and double click a Network Name from “Available Networks”. The chosen Network Name will then be listed in the Profile List. 2. From the Profile List, select one Profile and click “Modify” button 3. Select “Profile Editor” tab and edit the settings.
n n n n n n n n n n n n n n Configuration Name: This name identifies the configuration. This name should be unique. Network Name (SSID): The name of the wireless network. This name cannot be longer than 32 characters. If the field is set to be “ANY” or is left blank, your computer will connect to an AP with the best signal strength. Network Connection: Specifies the mode of the network. Two options are “Infrastructure” and “Ad Hoc”.
4. Select “Security Setting” tab and edit the settings. Click “OK” to save the settings. n n n n n Enable Security: Enables the WEP security when the check box is checked, and disables the WEP security when the check box is cleared. Default Encryption Key: Allows you to choose one type of encryption key to be used (Unique, First, Second, Third, or Fourth) from the drop down menu. Unique Key: Defines the unique encryption key for security for the current network configuration. Not used in Ad-Hoc mode.
5. Select “TCP/IP Property” tab. Enter the settings and click “OK” to save the settings. n n If the network uses DHCP server, choose “Obtain an IP address automatically”. If the network does not use DHCP server, choose “Use the following IP address” to set the relative settings. For the IP configuration information, please contact the network administrator. 5.1.
