Connected Cooler Radio Quick Start Guide
Table of Contents 1. GETTING STARTED ............................................................................................... 5 1.1 UNPACKING INFORMATION ......................................................................................5 1.2 INTRODUCTION......................................................................................................5 2. PORTS AND LED INDICATORS .............................................................................. 6 2.1 PORTS ........................
Declaration of Conformity Manufacturer: Name: Wistron NeWeb Corporation Address: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C Radio Equipment: Model: D52A1 Description: Connected Cooler Radio Rest of World version Marketing Name: D52A1 Radio-related Software Version: D52A1_v00.
Signed for and on behalf of: Wistron NeWeb Corporation Place: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.
1. Getting Started 1.1 Unpacking Information The Connected Cooler Radio (CCR) Battery notice card Battery Notice Card 1.2 Introduction The Connected Cooler Radio (CCR) works with sensors installed in coolers to deliver cooler information to Cloud servers for better monitoring and management. The Wi-Fi, AGPS, and 2G/3G (based on the models you select) functions of the CCR enables stable delivery of accurate information collected by analog or digital sensors.
2. Ports and LED Indicators 2.
2.2 LED Indicators Power RF Sensors LED Indication Description Power Steady green All self-tests passed, and the battery is full. Blinking green All self-tests passed, and the battery is charging No power connection Off RF Sensors Blinking red Other failures; for example, SIM card, battery, or Wi-Fi functions Unsuccessful antenna connection Steady blue The self-test mode is running. Blinking blue Detected function failure of the temperature sensor or door-open sensor.
3. Installation 1. Place the CCR in the specified location (for example wall) and affix the screws. Screw Screw Screw Screw use type M4 2. Attach the antenna to the antenna port of the CCR. Antenna 3. Connect the power port to the power supply.
4. Connect the Sensor port to the sensors. Sensors 5. Press the Self-test button. The system begins testing the CCR and the sensors attached to the CCR. Self-test button 6. The system will be ready for use when the Power LED returns to steady green, indicating the system functions normally. Refer to the “LED Indicators” section of this document for details if other LED indications are displayed.
4. Specifications Specifications Standards Wi-Fi: IEEE 802.11b/g/n (2.4 GHz) BLE 3G: B1/2/5/8; GPRS/EDGE Quad-Band Max. power for each frequency And Antenna Typy Antenna Gain Mobile Antenna Max. Power (dBm) peak Gain (dBi) GSM 850 34 1 E-GSM 900 34 0 DCS 1800 32 4 PCS 1900 30.
WLAN WiFi TX 11b/g/n Max Power(dBm) 17.9 Antenna peak Gain 1 (dBi) Antenna type internal PCB antenna BLE 4 Max Power(dBm) Antenna peak Gain 1 (dBi) Antenna type internal PCB antenna Regions and countries applicable Worldwide, out of USA and Canada. Connection interfaces USIM 3FF, VGA for sensor(optional) Power input 12 V DC/ 1A (powered by UL Listed power source.) Backup battery: 3.
5. Instruction Instruction CAUTION Only authorized service providers shall replace battery. Do not disassemble or open crush, bend or deform, puncture or shred Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, expose to fire, explosion or other hazard. Only use the battery with a charging system that has been qualified with the system per CTIA Certification Requirements for Battery System Compliance to IEEE 1725.
Specific Absorption Rate information This mobile device meets the government’s requirements for exposure to radio waves. Your mobile device is a radio transmitter and receiver. The exposure standard for mobile devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit adopted by Europe is 2.0 W/kg averaged over 10 grams of tissue.
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
