Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual WISENMESHNET® L-Series RS-485 Interface Node User Manual Model Name: 6501 Wuxi Wisen Innovation Co., Ltd. November 2019 www.wisencn.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual Revision History and Clarification Rev. Issue Date Revisions V1.0 01/11/2019 1 Issue st Written By Revised By Xiaoyan Huang Dr. Yan Wu Document Definition: It defines the specifications (i.e.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual Table of Contents 1. Product Introduction................................................................................................................................................... - 4 2. System Structure Layout ............................................................................................................................................. - 5 3. Node & Radio Features ...................
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual 1. Product Introduction ® The WISENMESHNET RS-485 Interface Node is one of the key products in our patented ® ® WISENMESHNET geotechnical safety monitoring system. Working together with the WISENMESHNET gateway product and the specified RS-485 type sensors, it intelligently delivers the real-time data of RS-485 type sensors to the information centre.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual 2. System Structure Layout Figure 2. System Structure Layout. www.wisencn.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual 3. Node & Radio Features Node Features: Basics Battery Power Qty. x 1 (3.6V Lithium primary D-Cell ER34615) Accuracy Stop Voltage 2.7VDC Mesh Stop Voltage 2.1VDC Battery Connection Standard Aluminium Battery Holder Working Current (DC) Max. 160mA (Typ. 100mA) Local Storage Min. 450 Messages during Meshing LxWxH Interface Node: 100 x 100 x 60mm Node Weight 0.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual No. of Mesh Hop* 6 Hops Supported Sampling Interval 1-60mins Antenna Description Mesh Antenna Omni-directional (20cm in length) or Customised 2/3/4G-Antenna Omni-directional 3.5dBi (20cm in length) or Customised Antenna Connector SMA (M) st st * E.g., the radio link from a gateway to the 1 layer node is called the 1 hop. 4. Terminologies Figure 4.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual 5. Operation Procedures 5.1.System Deployment Notifications 1) Location: The deployment location of a RS-485 Interface Node is usually determined by the required monitoring or inspection location; 2) Before any RS-485 Interface Node is switched on, two tasks will need to be carried out: A.
Wisen Innovation Technical Doc. No.2019 5) WISENMESHNET® L-Series RS-485 Interface Node - User Manual Sensor connections to Node: A. Strip the cable sleeve back by 8mm. B. The 5 wires from the cable are 12V_Out, GND, A, B and GND. Please refer to the sensor datasheet to identify the purpose of the stripped wires. C. Untighten the gland cover, insert cable through the gland, then connect the 5 wires accordingly. D.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual will enter a deep sleep mode until a new battery is installed; 5) If the data from nodes are showing unexpected results or are not being sent back to the Wisen gateway, then please carry out investigation using the following two stage procedure: A.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual 2 Mesh Antenna 200 1 3 Cap-Hex-Head Screw M6x14 4 4 User Manual* Downloadable from WISENMESHNET® 5 Inspection Report* Visualisation Platform. 8. Safety and Warning Warning: Please read the following instructions carefully.
Wisen Innovation Technical Doc. No.2019 WISENMESHNET® L-Series RS-485 Interface Node - User Manual Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer. When disposing of the batteries, please contact your local authorities or dealer and ask for the correct method of disposal. 9. Contact - Wuxi Wisen Innovation Co., Ltd.: www.wisencn.com - Email: marketing@wisencn.com FCC Warning - This device complies with part 15 of the FCC Rules.