User's Manual

ManualsBrandsWireless eSystems ManualsElectronicsModel TR101

UM04725

June 7, 2004

Rev -

USERS MANUAL

FOR THE

IRESPOND SYSTEM

Prepared by:

65 Hill Ave.

Fort Walton Beach, FL 32548

(850) 244-2332

Email: www.wirelessesystems.net

Note: This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by Micro Systems Inc. could

void the user's authority to operate the equipment.

Summary of content (8 pages)

PAGE 1
UM04725 June 7, 2004 Rev - USERS MANUAL FOR THE IRESPOND SYSTEM Prepared by: 65 Hill Ave. Fort Walton Beach, FL 32548 (850) 244-2332 Email: www.wirelessesystems.net Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
UM04725 June 7, 2004 Rev - TABLE OF CONTENTS Paragraph 1.0 2.0 2.1 2.2 2.3 2.4 2.5 2.
PAGE 3
UM04725 June 7, 2004 Rev - 1.0 SCOPE. This document provides information on the setup and operation of the IRespond System. The IRespond System is used in a classroom environment to allow an instructor to automate the test taking and grading process. 2.0 System Overview. The IRespond System consists of a single base station, thirty hand held remote modules and a software package which executes on a personal computer (PC) with a Windows XP operating system.
PAGE 4
UM04725 June 7, 2004 Rev - 2.1 Base Station Description. The base station controls message traffic flow between the PC and the Remote units. Note that the base station is a modified version of the Remote. A Universal Serial Bus (USB) interface and and a different software package are the major differences between the base station and Remote physically. The Liquid Crystal Display (LCD) display and keypad are used for diagnostic test and status display on the base station.
PAGE 5
UM04725 June 7, 2004 Rev - USB Connection: ACTIVE Remotes Active: 02 2378e9 112ca8 Figure 3. Base Station Display 2.3 Remote Module Description. The Remote provides the data entry point for the user of the IRespond system. The LCD graphics display, the programmable soft keys and cursor keys allow the user to quickly enter data for transmittal to the base station. Figure 4 shows the Remote features. Table I below explains the keypad assignments.
PAGE 6
UM04725 June 7, 2004 Rev - R E M O T E Figure 4. Remote Features To turn the unit on press the power key. To turn the unit off, press the power key again. Note that during testing the power off function is disabled until the test time has elapsed or enabled by the base station. 2.4 Remote Operation. The Remote units operate in concert with the base station, therefore the base station must be powered on and communication established with the IRESPOND application prior to Remote activation.
PAGE 7
UM04725 June 7, 2004 Rev - addition, information about the user, the number of questions answered/remaining, and the device number the user is employing can be displayed on the personal computer display. When the user has completed the test, the user will submit the test for scoring. The Remote will deliver any remaining or updated information to the Base Unit PC. This information will be passed through to IRESPOND for immediate grading and storage.
PAGE 8
UM04725 June 7, 2004 Rev - 2.6 Battery Pack Replacement. In the event that a battery pack will not remain charged and needs replacement then refer to Figure 6. Place the Remote on a flat surface with the display face down exposing the battery pack compartment on the rear of the Remote. Remove the battery cover screw with a cross tip screw driver. Press down on the battery pack connector clip on the pack in the unit. Gently remove the battery pack connector clip and remove the battery pack.