iRespond®-Touch Technical Manual Wireless eSystems
Table of Contents Touch Base Unit ------------------------------------------------------------ 1 Change the Channel --------------------------------------------------1 Adjust Power Output -------------------------------------------------1 Adjust Display --------------------------------------------------------2 Turn On/Off Channel Scan ----------------------------------------- 2 Setting Base UID -----------------------------------------------------3 Adjusting Base Offset -------------------------------------
Touch Base Unit Change the Base’s Channel To change base channel from main screen: 1. Press the power button 2. Use the up or down to turn on the Touch base. arrow keys to change the base’s channel. To change base channel from configuration menu: 1. Press the power button to turn on the Touch base. 2. When the base’s UID is displayed at the bottom of the main splash screen, press the following buttons in order: F2 , Backspace , and Flag . 3.
5. Select the button under Pow. 6. Use the up or down 7. Select the F1 arrow keys to change the power setting. button to save. 8. Press the power button to turn off the base. Adjust the Base’s Display To adjust the contrast of a base if it appears too light or too dark: 1. Press the power button to turn on the Touch base. 2. When the base’s UID is displayed at the bottom of the main splash screen, press the following buttons in order: F2 , Backspace , and Flag . 3.
2. When the base’s UID is displayed at the bottom of the main splash screen, press the following buttons in order: F2 , Backspace , and Flag . 3. From the diagnostics screen, press the soft button under CFG. 4. From the Configure Unit screen, select the soft key under MIS. 5. Press the soft button under SCN to turn on (SCN is highlighted) and off channel scanning. Setting Base UID The Touch base’s UID is set before it is shipped and should not be changed. 1. Press the power button 2.
1. Press the power button to turn on the Touch base. 2. When the base’s UID is displayed at the bottom of the main splash screen, press the following buttons in order: F2 , Backspace , and Flag . 3. From the diagnostics screen, press the soft button under CFG. 3. From the Configure Unit screen, select the soft key under RF. 4. Connect spectrum analyzer to base’s antenna connection. 5. Offset #1 is for Lite remotes, Offset #2 is for Touch remotes.
Touch Remote Unit To Login by PIN An iRespond session must be running to login to a remote. 1. Press the power button 2. to turn on the Touch remote. At the Enter your PIN screen, use the stylus to enter in your unique PIN. (If Username and Password is displayed instead of Enter your PIN, select the middle soft button under PIN.) 3. Use the << button on the touch screen or backspace entries. button to delete 4.
4. If you are required to enter a password, tap TAB on touch screen or tap inside the password textbox with the stylus. Otherwise, skip ahead to 6. 5. Use the stylus to select the characters of your password from the keyboard displayed on the Touch remote. 6. Press ENT on the touch screen or the ENTER button. 7. If the Username or Password was entered incorrectly, the remote will display Login Failed. 8. Press OK on the touch screen and reenter username and password.
2. To change an answer, tap the checked checkbox again with the stylus. Tap the checkbox of your new answer choice. 3. Press ENT on the touch screen or the ENTER question or to submit your answers. button to go to the next To Answer Fill-in/Short/Essay Response Questions 1. Using the stylus, tap inside displayed text box. Use the stylus to enter the correct alpha/numeric response(s) from the keyboard displayed on the remote unit. 2.
. At PIN screen you can log in to join a session or power off remote. To Edit/Review Homework File Saved to the Remote 1. From the login screen of the remote, select the softkey button under HWK. 2. Using the stylus select the homework file you wish to edit. 3. Press the softkey button under Open. 4. Using the stylus tap incorrect checkbox answers to deselect them. To edit Fill-in questions use tap inside textbox and select << or the backspace button to delete the answer.
Not available during Instructor-Paced sessions. and right arrow buttons or the left and right arrows on the 1. Use the left touch screen to review through questions. Change the Remote’s Channel To change the remote’s channel from configuration menu: 1. Press the power button to turn on the Touch remote. 2. When the Touch’s UID is displayed at the bottom of the main splash screen, press the following buttons in order: F2 3. , Backspace , and Flag .
5. Using the stylus, tap the top leg of the crosshair in the upper left hand corner of the remote. The crosshair should now move to the upper right hand corner of remote. 6. Using the stylus, tap the top leg of the crosshair in the upper right hand corner of the remote. The crosshair should now move to the lower right hand corner of remote. 7. Using the stylus, tap the top leg of the crosshair in the lower right hand corner of the remote.
Adjust the Remote’s Display To adjust the contrast of a remote if it appears too light or too dark: To adjust contrast from the configuration menu: 1. Press the power button to turn on the Touch remote. 2. When the remote’s UID is displayed at the bottom of the main splash screen, , Backspace press the following buttons in order: F2 , and Flag . 3. From the diagnostics screen, press the soft button under CFG. 4. From the Configure Unit screen, select the soft key under DIS. 5.
3. From the diagnostics screen, press the soft button under CFG. 4. From the Configure Unit screen, select the soft key under MIS. 5. Press the soft button under ADR. 6. The display will look similar to this 0 12 44 56 < 3. The four sets of numbers to the left of the < represent the hex bits of the UID address. The 3 to the right of < represents the current position we are at. The 3 represents the 0. Pressing the up or down arrows will increment 0 one at a time. Pressing Backspace increments 0 by 10.
Turning Automaton On/Off The Automaton is for testing purposes ONLY. The automaton allows the remote to randomly select an answer to any questions it receives 1. Press the power button to turn on the Touch remote. 2. When the remote’s UID is displayed at the bottom of the main splash screen, press the following buttons in order: F2 , Backspace , and Flag . 3. From the diagnostics screen, press the soft button under CFG. 4. From the Configure Unit screen, select the soft key under MIS. 5.
2. When the remote’s UID is displayed at the bottom of the main splash screen press F1 3. . The remote will display “RF Program Utility” 4. When the remotes have been configured they will automatically power down. 5. Remote will shut off when it has completed configuring. Play Drop Zone Game 1. Press the power button to turn on the Touch remote. 2. When the remote’s UID is displayed at the bottom of the main splash screen, press the following buttons in order: F2 . 3. Press F1 4.