LG2-01 Manual Table of Contents 1. Warnings 2. Introduction 3. Product Features 4. Specifications 5. Package of Contents 6. System Connections 7. Transmitter Battery Installation 8. Transmitter Operations 9. Accessory 10.
15.105 Federal Communications Commission (FCC) Requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1. Warnings - - Before you using your system, please check the power of transmitter and receiver. When you use the Ni-Cad batteries to power your system, DO NOT connect the power adapter when you are operating the transmitter. To prevent accidents, overheating and short circuits. Please turn on the transmitter first and then the receiver, to prevent the loss of control. To prevent operate the system outdoor on rainy days, the system are not designed for waterproof.
. Specification A. Transmitter - Modulation type: FM(FSK) - Power requirement: 12V (AAx8) - Current drain: 140mA - Coding type: PPM - Frequency: 27MHz - RF power: 200uW B. Receiver - Modulation type: FM(FSK) - Power requirement: 6V (AAx4) or BEC - Weight: 19.5 g. - Dimension: 45.5 x 30.5 x 22.5mm - Current drain: 20mA except servo C. Servo - Power requirement: 4.8~6V - Current drain: 8mA (at 6V/ Idle ) - Speed: 0.23sec/60 ﾟ(at 4.8V) - Torque: 3.2Kg-cm (at 4.8V) - Weight: 37.2 g - Size: 40.4 x 19.
6. System Connections Receiver and servo connections Non-electric Model - When you install the system in an non-electric model (or mechanical type speed control), you should use the battery holder to supply the power for receiver E.S.C. Installation Model Connection Precautions A. Installation Note - After you installed the system, please check the receiver, servo, and battery connections, make sure all the connections are fully inserted.
B. Receiver Note - Keep the receiver away from motor or engine when attaching to the chassis of car or boat. - Keep the receiver away from the power wires to prevent the interference. - Refer you model instructions, run the antenna up the antenna tube to gain the best receiving effect. - DO NOT cut off the excess antenna wire, or it will shorten the operation range.
8. Transmitter Operations D. Steering Reversing Switch E. Throttle Reversing Switch A. Antenna H. Steering Trim I. Throttle Trim B. Power Switch C. Power Indicator LEDs O. Multi-function Switch N. 2/3CH Mode Switch F. Steering Wheel P. Neck Strap Hook G.Throttle Trigger J. Steering Dual Rate Holder M. Crystal K. Charger Jack L.Battery Cover A. Antenna - Please extend the antenna to the full length when you operating, to gain the best radio performance. - Be careful to handle the antenna, do not bend it.
G. Throttle Trigger - Use the throttle trigger to control the throttle and braking for your model. - Pull the trigger for throttle and push it for braking or reverse. (some of the ESCs support the Reversing function) H. Steering Trim - Before you use the steering trim, you should center servo horn closer to the neutral position with the linkage, and then use the trim to fine-tune the steering. - Adjust the steering trim to make your model running perfectly straight when the steering wheel is centered. I.
. Accessory A. Charger - When you use the rechargeable batteries (ex. Ni-Cad battery), you can insert the connector of the charger into the jack to charge the batteries. DO NOT charge the non-rechargeable batteries (ex. Dry batteries), it may cause the unexpected explosion. B. Sticker - You can design any wording with the character sticker to personalize your transmitter, receiver and servo. Figure C.
. Reference A. Troubleshooting If your R/C system works abnormally, ex: remote range is short, transmitter malfunction, etc, please check the table below to take the action to solve the problem, if it couldn’t solve the problem, and then please contact your dealer to get the service. Problem Check point Batteries low Remote range is short Servo is not running smoothly Operation stops intermittently Model is glitch or servo is running erratically Crystal wrong, damage or disconnected.
