High Power Wi-Fi Repeater User Manual Quick Installation Guide(Q.I.G.) REV.1.
Introduction： The Wi-Fi Repeater is a combined wired/wireless network connection device designed specifically for small business, office, and home office networking requirements. It allows a wireless network to be expanded using multiple access points without the need for a wired backbone to link them. It also works well with other 11b/g and 11n protocol wireless products.
Getting Started Setting up a Wireless Infrastructure Network For a typical wireless setup at home (as shown below), please do the following: Wireless Repeater Mode You will need WiFi AP/Router Internet access Wireless AP Mode You will need broadband Router Internet access Connect the WiFi-Repeater to your Router/Switch with RJ-45 Cable
How to configure the Wi-Fi Repeater You can configure the Wi-Fi Repeater by connecting it with your computer/laptop with enclosed RJ45 cable or wirelessly. We recommend you to do it with wire. A. Configure the Wi-Fi Repeater with RJ45 Cable A1. Plug the Wi-Fi Repeater to a wall socket. Connect your computer / laptop with the Wi-Fi Repeater with enclosed RJ45 Cable. A2. Click the “Start” button (it should be located at the lowerleft corner of your screen), then click “Control Panel”.
A4. Open web browser and type http://192.168.10.1 in the browser's address box. This number is the default IP address for this device. A5. The login screen below will appear. Enter the “User Name” and “Password” and click “OK” to login. The default User name is “admin” and the Password is “admin”. A6. After logging in and click “Setup Wizard”, you will see the web page below: Select “Wireless Repeater Mode (Station)” and click on ‘Next’ to continue.
A7. Click on ‘Repeater – OneKey Setting’ button A8. Wait a few seconds and you will see the site below and please click on ‘Wireless Network Selection’ button.
A9. Click on ‘Refresh List’ button. Select the Wireless SSID and click ‘Next’ to continue. A10. When you see the site below, please do not change any setting but only insert the password of your network. Click on ‘Apply and Reboot’ button.
A11. Click ‘OK’ to confirm. The Repeater will restart. A12. Wait a few seconds and you will see the status site like below. It means your Wi-Fi Repeater is ready for use. * The Wi-Fi Repeater1 WLAN key is same with your router. If you do not see the site like above, you need to re-configure it again. NOTE: If you need to reset the Wi-Fi Repeater, you need press the reset button inside the tiny hole for 10 seconds.
B. Configure the Wi-Fi Repeater wirelessly. 1. Plug the Wi-Fi Repeater to a wall socket. 2. or ) on Click on the network icon ( the right bottom of your desktop. You will find the signal from the Wi-Fi Repeater. Click on ‘Connect’ and wait for a few seconds. 3. Follow process A3 to A12 to configure your Wi-Fi Repeater wirelessly. C. Configure the Wireless AP Mode. 1. 2. 3. Plug the Wi-Fi Repeater to a wall socket. Follow process A2 to A5.
4. Click on ‘AP – OneKey Setting’ button 5. Wait a few seconds and you will see the status site like below. It means your Wi-Fi Repeater is ready for use.
How to connect your computer/laptop with the Wi-Fi Repeater Adding a Wireless computers to the WiFi-Repeater 1. 2. Log on to the computer. Open Connect to a Network by right-clicking the network icon ( ) in the notification area. 3. Choose the wireless network from the list that appears, and then click Connect. Type the network security key or passphrase if you are asked to do so, and then click OK. You'll see a confirmation message when you are connected to the network.
Configuring via Web Browser Wireless Base Configuration Please click “Wireless -> Basic Settings” located at the web management interface, the following message will be displayed on your web browser: You could configure the minimum number of Wireless settings for communication, such as Network Name (SSID) and Channel. The Access Point can be set simply with only the minimum setting items.
Wireless Security Configuration Please click “Wireless-> Security” located at the web management interface, the following message will be displayed on your web browser: Setup the wireless security and encryption to prevent from unauthorized access and monitoring. Supports 64/128-bit WEP, WPA, WPA2 encryption methods. Select SSID: Root - Client - XXXX: Repeater AP – WiFi-Repeater1: The password of the WiFi Repeater will be the same as your XXXX router.
Factory Default and Settings Backup , Restore You can backup all Setting of this router to a file, so you can make several copied of router configuration for security reason.
Firmware Upgrade The system software used by this router is called as ‘firmware’, just like any applications on your computer, when you replace the old application with a new one, your computer will be equipped with new function. You can also use this firmware upgrade function to add new functions to your router, even fix the bugs of this router.
Change Management password Default password of Wireless Router is “admin”, and it’s displayed on the login prompt when accessed from web browser. There’s a security risk if you don’t change the default password, since everyone can see it. This is very important when you have wireless function enabled.
Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
