User's Guide

DESCRIPTIONS
Front
Double Ring
Single Ring
Single Ring
Triple Ring
Single Bullseye
Double Bullseye
Screw
Hole
Sticker
Area
Bullseye
Adjusment
Hole
Bluetooth
LED Indicator
●
Red LED Blinking: waiting
for connection
● Blue LED On: device connected
● Red LED On: connected with
an external device such as
Gamebox
B
LUETOOTH
D
ARTBOARD
INSTALLATION MANUAL
&
USER GUIDE
EVA PAD
Hanging Hole
EasyFit plate had installed onto
dartboard backside, using wall
bracket to perform instant
assembly, when using EasyFit it
required 5mm EVA pad to make
the dartboard perpendicular
with floor, to perform best result
of the game play. When using
EasyFit, the noise reduction will
perform worse than directly install
the board to the wall.
When EasyFit completely installed
per installation manual, it can hold
up to 5kg weight force safely.
ACCESORIES
Soft Tip x 30 Barrel x 6 Shaft x 6 Flight x 6 Wall Plug Fisher x 4 Screw x 4
USER GUIDE
PRODUCT SPECIFICATION
Install 2 AA batteries
Make sure battery cover
is closed and secure.
Hang dartboard onto
proper position
Press the Power switch down
to turn the dartboard on
Download SDB apps
and sign up
LED turns BLUE for
complete connection
Item No.
Bluetooth ver.
Dimension
Weight
Power Input
Power
SDBA1000ARA
Bluetooth 4.0
472 x 472 x 36.5mm
±1.8kgs
2 AA Bateries
100mW
Back
INSTALLATION
Mark dartboard center point position.
Add adhesive sticker onto EasyFit backside
at position shown in the diagram below.
Install the Easyfit bracket by pressing it
firmly against the wall
IMPORTANT NOTE!
● For added security, install 4 screws through the bracket into
the wall.
● Do not install the mounting bracket on a surface with fabric.
The adhesive is at risk to detach causing the dartboard to fall.
● Do not install the dartboard in any area where valuables people
or animals could be present. Avoid mounting above sofas, beds
and chairs to prevent any chance of injury.
STEP STEP
STEP STEP
REMOVING THE DARTBOARD AND BRACKET FROM THE WALL
Remove the dartboard.
Holding the EasyFit bottom groove as shown in the diagram.
Gently pull-off both sticker on bottom side.
Gently pull-off the sticker on top side.
Pull down in
perpendicular
direction
Need to pull down
until its stretched more
than 12 inches / 30 cm
NOTE!
TRANSPORTATION
●
Do not place any objects on the surface of the
dartboard o prevent dartboard sensor from
not-registered issue.
INSTALLATION
●
Always make sure the walls are clean before
assembling the EasyFit hanger bracket to
ensure it will stick well.
●
Turn on the dartboard FIRST and then open the
SDB APP on your mobile device. The APP will then
find and connect to the dartboard automatically.
●
If connection fails, please turn-off and restart
both dartboard and mobile device, then follow
again step 1. If still connection fails, please use
the customer feedback service which integrated
on apps to send customer feedback. Check your
mobile device to make sure Bluetooth is enabled
and ON.
●
Please use soft-tip darts and never use steel-tip
darts or it may damage your dartboard.
●
Please note weak batteries can cause scores not
to register. Replace old batteries with fresh
batteries
●
I f a dart tip breaks and gets stuck in the dartboard,
carefully use pliers to remove the broken tip from
the dartboard. Never push the tip fragment into
the dartboard.
IN USAGE
FCC Statement:
Guide the circle shaped hanger on the
backside of the dartboard into the grooved
slot of the Easyfit mounting bracket
Battery Cover
(required 2AA battery)
Power Button
Bottom
Bluetooth
LED Indicator
Hanging Hole
Please keep this
cardboard as it
for noise reduction