User's Manual

5. Caller ID Display
Note: Caller ID Display is a network service; please consult your network provider
for details.
Caller ID can be displayed in 3 ways:
a) By Name
YD-V16 can display the caller’s name when receiving call. To display caller’s
name, the name must be stored in the phone book.
b) By Phone Number
Phone number will be displayed if there is no record of that number in the
phone book
c) Withheld Number
When a caller withholds his number, WITHHELD will be displayed
Note: The YD-V16 do not automatically save numbers dialed directly from your
mobile phone and will not be displayed.
6. Call Waiting
Note: Call Waiting is a network service, please consult your network provider for details.
To accept an incoming call during a conversation:
• Press the Send button and the phone will automatically switch to Line 2
To switch calls between the two lines:
• Press the Send button to switch between lines
• Turn off the YD-V16 when not in use
• Attach the YD-V16 carefully and firmly to your rearview mirror (Please refer to
instructions on how to attach the YD-V16 to your rearview mirror)
• Do not let the YD-V16 be in contact with liquid as it is not waterproof. Avoid putting
it in places where there is excessive moisture and humidity.
• Do not expose the YD-V16 to direct sunlight or place in areas with high temperature,
as it may result in an explosion
• If the YD-V16 is not in use for a prolonged period, store in a cool, dry place, free
from moisture, humidity and dust
• Do not use abrasive cleaning solvents to clean the YD-V16
• Do not expose the YD-V16 to contact with sharp objects as this will cause scratching
and damage
• Do not stick anything inside the YD-V16 as this may damage internal components
• Do not attempt to disassemble the YD-V16, as it does not contain serviceable
components
• Only use the manufacturer supplied charger when charging the YD-V16
• Only charge the YD-V16’s built-in battery in accordance with the instructions of this
user guide
For questions or issues regarding the product, please visit www.letsyada.com or contact
Winplus in your area/region to speak to our customer service representative:
Winplus USA Tel. [phone]
Tel. [phone]
Winplus Europe Tel. [phone]
Winplus Australia Tel. [phone]
Winplus New Zealand Tel. [phone]
Winplus Asia Tel. [phone]
You can also contact us online by visiting www.winplus.com for more information about
the product.
IF YOU ARE EXPERIENCING ANY ISSUES WITH THE PRODUCT DURING OPERATION, DO NOT
RETURN THE PRODUCT TO THE STORE. CONTACT WINPLUS DIRECTLY FOR INSTRUCTIONS ON
HOW TO RETURN/EXCHANGE THE PRODUCT.
• Do not disassemble the charger as it may expose you to dangerous voltages or
other risks. Incorrect reassembly can cause electric shock when the YD-V16 is
subsequently used
• Do not use the charger outdoors or in damp areas
• Avoid charging the YD-V16 in extremely high or low temperatures
• It is recommended to charge the YD-V16 immediately whenever low battery power
is encountered to prolong durability & standby time
If you are unable to pair your mobile phone with the YD-V16:
• Make sure the battery is fully charged
• Turn off the YD-V16 and turn it on again
• Turn off all other Bluetooth
®
devices before you start pairing
• Ensure your mobile handset’s Bluetooth
®
feature is activated. Please refer to your
mobile handset user guide for specific instructions
• Repeat pairing procedures
• Ensure the YD-V16 is within a maximum of 10 meters of your mobile handset(s) or
Bluetooth
®
enabled device and there are no obstructions, such as wall or other
electronic devices, in between as it may cause interference transmission
• If all the above steps do not resolve your problem, please remove the battery for at
least 20 minutes
The YD-V16 Rearview Mirror Speakerphone is compliant with and adopts the Bluetooth
®
Specification V1.2. However, interoperability between the device and other
Bluetooth
®
-enabled products is not guaranteed because it depends on compatibility.
For more information on the compatibility between the device and other
Bluetooth
®
-enabled products, please contact Customer Service.
If the LCD display hanged or all button functions disabled:
• Use the RESET switch at the back of the unit
WINPLUS NORTH AMERICA
LIMITED WARRANTY
WINPLUS North America warrants, to the original purchaser, that its products
are free from defects in material and workmanship for 90 days from the date
of original purchase. Where permitted by law, WINPLUS North America’s
liability shall be limited to that set forth in this limited express warranty. This
limited express warranty shall be the exclusive remedy of the purchaser and
WINPLUS North America makes no other warranty of any kind aside from the
limited express warranty stated above.
Note: Warranty only applies for North American customers or purchases made
in the North America.
YD-V16 User Manual
www.letsyada.com
Thank you for purchasing the latest Yada wireless
technology product from Winplus. We hope you will
enjoy all features and benefits offered by the YD-V16
Bluetooth
®
Rearview Mirror Speakerphone. These features
and benefits were designed with the goal of making
wireless communication more convenient for the user.
Winplus USA
375 W. Apra St. Rancho Dominguez, CA 90220
[e-mail]
www.winplususa.com
Winplus Europe
Unit 4, Two Counties Estate, Falconer Road,
Haverhill, Suffolk CB9 7XZ, UK
[e-mail]
www.winplus.net
Winplus Asia
Suite 6-11, 7th Flr Corporation Park
11 On Lanai St., Shatin NT, Hong Kong
[e-mail]
www.winplus.net
Winplus Australia
Unit 2, 991Mountain Hwy Boronia
Victoria, Australie 3155
[e-mail]
www.winplus.com.au
Winplus New Zealand
22-24 Olive Road, Penrose
Aukland, New Zealand
Griffiths Equipment
[e-mail]
www.types.co.nz
• Distracted driving is dangerous. Always use the Bluetooth
®
Device in a manner
that does not reduce your attention and ability to drive carefully and safely.
• Adhere to all applicable traffic laws and motor vehicle regulations applicable
to the device.
• Consult local laws and regulations for any restrictions on installation or use.
• Do not install on or near an airbag. Such installation could interfere with airbag
deployment or could cause the product or another object to become a
projectile, which could result in serious personal injury to occupants.
• Ensure the product location will not obstruct your vision while driving.
• Observe all signs that require an electrical device or RF radio product to be
switched off in the designated areas. These could include hospitals, blasting
areas, and potentially explosive atmospheres.
• Never allow children to play with the device. Small parts may be a choking
hazard.
• Always practice safe driving habits.
• Ensure that the charging cable does not interfere with your line of site while
driving when the device is being charge.
• Improper use and installation may cause severe injuries, make sure to follow
installation instruction and safety procedure.
CONTENTS
1 2
3 4
DISCLAIMER
WARRANTY / LIABILITIES
PACKAGE CONTENT
INSTALLATION
BATTERY OPERATIONS
SPEAKERPHONE OPERATIONS
BUTTON FUNCTIONS
LCD DISPLAY INDICATION
LED INDICATION
CARE AND MAINTENANCE
TROUBLE SHOOTING
CUSTOMER SERVICE / CONTACT US PAGE
FCC/ ICC
DISCLAIMER
WARRANTY / LIABILITIES
PACKAGE CONTENT
SPEAKERPHONE OPERATIONS
BATTERY OPERATIONS
BUTTON FUNCTIONS
LCD DISPLAY INDICATION
TROUBLE SHOOTING
FCC/ ICC
LED INDICATION
CARE AND MAINTENANCE
CUSTOMER SERVICE / CONTACT US
INSTALLATION
© 2008 Winplus North America Inc. All Rights Reserved. Winplus, the logo design, and yada are trademarks or registered
trademarks of Winplus North America Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and
any use of such marks by Winplus North America Inc. is under license.
U.S. and International Patents Pending
CONDITIONS OF WARRANTY
If during the 90 day warranty period your new product is found to be defective,
WINPLUS North America will repair such defect, or replace the product, without
charge for parts or labor subject to the following conditions:
1. All repairs must be performed by WINPLUS North America.
2. All warranty claims must be accompanied by a copy of the sales receipt or
bill of sale.
3. The equipment must not have been altered or damaged through
negligence, accident, improper operation, or failure to follow the product
instructions for installation, use, or care.
4. The replacement of parts is excluded from the warranty when replacement
is necessary due to normal wear and tear.
5. Repair or replacement parts supplied by WINPLUS North America under this
warranty are protected only for the unexpired portion of the original
warranty.
6. This is a “repair or replace” warranty only, and does not cover the costs
incurred for the installation, removal or reinstallation of the product, or
damage to any mobile phone devise or vehicle.
OWNER’S RESPONSIBILITIES:
WINPLUS North America will make every effort to provide warranty service
within a reasonable period of time. SHOULD YOU HAVE ANY QUESTIONS ABOUT
SERVICE RECEIVED OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING SERVICE,
PLEASE CALL TOLL FREE 1.866.294.9244 DURING REGULAR BUSINESS HOURS
MONDAY THROUGH FRIDAY 9:00 AM TO 5:00PM.
Note: Toll Free # is for North America Customers ONLY. See Customer service
section for customer contact numbers for other regions/offices.
In order to provide you with the proper warranty service, we request that you
adhere to the following procedure:
1. Include a copy of your sales receipt or bill of sale with your unit when it is
returned for warranty service.
NORTH AMERICA
EUROPE
AUSTRALIA
NEW ZEALAND
ASIA
Tel: [phone]
Fax: [phone]
Tel: [phone]
Fax: [phone]
Tel: [phone]
Fax: [phone]
Tel: [phone]
Fax: [phone]
Tel: [phone]
Fax: [phone]
375 West Apra Street
Rancho Dominguez, CA 90220
Unit 4, Two Counties Estate, Falconer Road,
Haverhill, Suffolk CB9 7XZ, U.K.
Unit 2, 991 Mountain Hwy Boronia,
Victoria, Australia, 3155
22-24 Olive Road, Penrose,
Auckland, New Zealand
Suites 6-11, 7th Floor Corporation Park,
11 On Lai Street Shatin, N.T., Hong Kong
2. If it is necessary to return your product for service, please return it securely
packed, preferably in the original shipping box, and freight and insurance
prepaid to the following address:
ATTN: WINPLUS YADA BLUETOOTH
®
PRODUCTS RETURNS
375 W. Apra St.
Rancho Dominguez, CA 90220
3. Please include a detailed explanation of the problem you are having.
4. If your product is found by WINPLUS North America to have a defect in
material or workmanship, within the warranty period, it will be repaired or
replaced at no charge and returned to you prepaid.
WINPLUS North America makes no other warranty of any kind aside from the limited
express warranty stated herein.
DISCLAIMER OF WARRANTIES, INCLUDING WARRANTY OF MERCHANTABILITY AND
WARRANTY OF FITNESS FOR PARTICULAR PURPOSE: EXCEPT AS SPECIFICALLY SET
FORTH HEREIN, NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, IS MADE AS
TO THE YD-V16 BLUETOOTH
®
REARVIEW MIRROR SPEAKERPHONE. EXCEPT AS
EXPRESSLY SET FORTH HEREIN, WINPLUS NORTH AMERICA AND/OR ITS AFFILIATES
EXPRESSLY DISCLAIMS, WITHOUT LIMITATION, ANY STATUTORY WARRANTIES AND ALL
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
WINPLUS North America and/or its affiliates are not responsible for a user’s intended
or actual use of the YD-V16 Bluetooth
®
Rearview Mirror Speakerphone. In no event
shall WINPLUS North America and/or its affiliates have any liability for any losses
(whether direct or indirect, in contract, tort or otherwise) incurred in connection with
the YD-V16 Bluetooth
®
Rearview Mirror Speakerphone. Neither shall WINPLUS North
America and/or its affiliates have any liability for any decision, action or inaction
taken by any person in reliance on the YD-V16 Bluetooth
®
Rearview Mirror
Speakerphone, or for any delays, inaccuracies and/or errors in connection with the
YD-V16 Bluetooth
®
Rearview Mirror Speakerphone and its functioning.
WINPLUS North America and/or its affiliates shall have no responsibility or liability for
damage and/or injury resulting from accidents while user is utilizing the YD-V16
Bluetooth
®
Rearview Mirror Speakerphone; and WINPLUS North America and/or its
affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss
or damage, incidental or consequential, arising out of the use or intended use of
the product.
5 6
WINPLUS EUROPE
LIMITED WARRANTY
WINPLUS warrants, to the original purchaser, that its products are free from
defects in material and workmanship for 12 months from the date of original
purchase. Where permitted by law, WINPLUS liability shall be limited to that set
forth in this limited express warranty. This limited express warranty shall be the
exclusive remedy of the purchaser and WINPLUS makes no other warranty of
any kind aside from the limited express warranty stated above.
OWNER’S RESPONSIBILITIES:
In order to provide you with the proper warranty service, we request that you
adhere to the following procedure:
1. Include a copy of your sales receipt or bill of sale with your unit when it is
returned for warranty service.
2. If it is necessary to return your product for service, please return it securely
packed, preferably in the original shipping box, and freight and insurance
prepaid to the following address:
ATTN: WINPLUS BLUETOOTH
®
PRODUCTS RETURNS
Unit 4, Two Counties Estate, Falconer Road
Haverhill, Suffolk CB9 7XZ, UK
3. Please include a detailed explanation of the problem you are having.
4. If your product is found by WINPLUS to have a defect in material or
workmanship, within the warranty period, it will be repaired or replaced at
no charge and returned to you prepaid.
WINPLUS makes no other warranty of any kind aside from the limited express
warranty stated herein.
WINPLUS AUSTRALIA
LIMITED WARRANTY
This product is warranted against faulty workmanship for a period of 12 months
from the date of purchase. Winplus’ liability is limited to replacement of the
product. Claims for associated or consequential loss or damage will not be
accepted by Winplus. Product is not fitted, used or installed in accordance with
instructions will not be eligible for warranty.
WINPLUS makes no other warranty of any kind aside from the limited express
warranty stated herein.
• Pull the tension clamp and clip to the existing rearview mirror
• Push the rearview mirror speakerphone until it is flushed against
original rearview mirror
Warning: Do not pull or remove the rearview mirror without pulling apart the
tension clamp.
B. Low Battery Power Indicator
When battery power is low, the device will:
• Flash red LED light
Recharge the YD-V16 immediately after the low battery indicators are detected.
The LED light will not turn on indicating battery power is completely consumed.
Follow “Charging The Batteries” instructions above to recharge the YD-V16.
The YD-V16 will not power on until it is connected to a power outlet to recharge.
Recharge the YD-V16 sufficiently before using.
7 8
IMPORTANT: Before using the YD-V16 Bluetooth
®
Rearview Mirror
Speakerphone:
• Fully charge the battery (8 hours continuous) for first time use
• Only use rechargeable batteries provided
A. Charging the Battery
Follow the steps below when charging the YD-V16 Bluetooth
®
Rearview Mirror
Speakerphone
• Connect the DC power jack to the YD-V16 Bluetooth
®
Rearview Mirror
Speakerphone
• Connect car charger to cigarette power outlet
• LED will flash red when charging is initiated
• Red LED will flash off when charging is complete
IMPORTANT: Remove device from cigarette outlet before leaving the
vehicle. Do not leave the YD-V16 Bluetooth
®
Rearview Mirror Speakerphone
charging in the vehicle unattended.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
Note: Actual talk time and standby time for the YD-V16 will vary with different
Bluetooth
®
enabled mobile phones due to different implementation of power
down modes.
A. Power on/off
To turn the YD-V16 on:
• Press and hold the Power Switch Button
until the LED flashes blue
• Release the button and wait for YD-V16
to enter into search mode Searching
• Device will stay in search mode for 5 seconds
• If no device was found, YD-V16 will stay on the screen
• To search again, press phone button
once to activate search mode Searching
Note: Before automatic connection, please make sure Bluetooth
®
mode on your
mobile phone is activated and you must have at least successfully paired and
connected to YD-V16 at least once in order to activate this feature.
To turn the YD-V16 off:
• Press and hold the Power Switch Button for at least 5 seconds
B. Pairing/Linking
Pairing Bluetooth
®
enabled devices like mobile phones with the YD-V16
Bluetooth
®
Rearview Mirror Speakerphone authorizes the devices to work with
each. This step only needs to be performed once.
Before Pairing the YD-V16 Bluetooth
®
Rearview Mirror Speakerphone:
• Ensure the YD-V16 is fully charged
• Charging cable is disconnected
• You have the pairing instruction of your Bluetooth
®
wireless phone
9 10
It is recommended that you follow the pairing instructions provided by your
mobile phone to ensure you successfully pair the YD-V16 Speakerphone with
your mobile phone. If you do not have your mobile phone’s instruction manual
available, follow the typical pairing instructions below:
• Power on the YD-V16 and wait until device completed the search mode
• Press and hold MENU for 2 seconds
• Screen will indicate Pair Mode
• Turn on your mobile phone
• Select SET-UP or CONNECT from your mobile phone menu
• Find and select OPTION to discover Bluetooth
®
devices; establishing a
connection may take several minutes
• If found, phone display should indicate YD-V16 or
Select “YD-V16” from the list
• Phone should give you a prompt asking if you want to pair the device
• Select OK or ACCEPT and wait for prompt to enter passkey or PIN
• Enter the code 0000 when a passkey is requested
• Select “OK” to pair the YD-V16 and the handset
• When pairing is complete, the YD-V16’s LCD will show PAIRING SUCCESSFUL
icon Pair OK
Note: If the YD-V16 and mobile handset did not successfully pair, follow the steps
below to retry pairing:
• Turn the phone off; wait for 10 seconds
• Turn phone power on
• Repeat the pairing instructions from the beginning
To Link YD-V16 to your mobile phone after pairing:
• Pressing the SEND button of your YD-V16 or
• Establishing the connection via your mobile phone
Note: Make sure Bluetooth
®
has been activated on your mobile phone before
you press the SEND button. (Please refer to your mobile’s operation manual
about connecting Bluetooth
®
devices)
Once it is connected:
• YD-V16 will emit a beep
• The mobile’s ID will be displayed on the screen (Ex. “Motorola V3”)
C. Phonebook
1. Phonebook Set-up via AT Command
AT Command and OPP (Object Push Profile) function can automatically
transfer the contacts in your mobile phone to the YD-V16 Rearview
Mirror Speakerphone.
Note: NOT ALL MOBILE PHONES SUPPORT AT Command and OPP Features
To transfer the Phone Book from your mobile phone via AT Command:
• Make sure the YD-V16 and mobile phone is connected
• Press Menu
• Scroll the menu by pressing or button until you see Contact list
• Press Menu button to enter Phonebook Transfer Inquire
• Press Send button to start or press End button to end
• LCD will display Downloading... to indicate Phonebook transfer is in process
• Once transfer is successful, LCD will display Download Complete
11 12
2. Phonebook Set-up via OPP
The YD-V16 supports single contact or group contacts transfer via OPP function.
For details on operating procedures, please refer to your mobile phone’s user
manual
To transfer the Phone Book from your mobile phone via OPP:
• Disconnect Bluetooth
®
link from the YD-V16 setting (if it is connected)
• Setup mobile phone for copying and transferring the contacts from the
mobile phone to your YD-V16
Note: Please refer to your mobile phone’s user manual
• LCD will display Downloading to indicate contacts transfer is in process
• Once transfer is completed, LCD will show number of records transferred
• Reconnect the Bluetooth
®
link of your YD-V16 and mobile phone
Note: Some mobile phones are able to register multiple phone numbers under
the same name. The YD-V16 phonebook can distinguish the numbers using the
letters: <M> for mobile phone number, <H> for home number and <O> for office
number
3. Deleting Phonebook entries:
To delete Phone Book entry:
• Press Menu
• Scroll the menu by pressing or button until you see Delete Contact
• Press Send button
• LCD will display Yes or No?
• Press Send button to confirm.
• LCD will display Deleting Contact while phone book entries are being deleted
• LCD will display Deleted ALL when phone book is cleared
• Press End button to return to Main Menu
Note: YD-V16 does not allow deleting of a single entry; ALL entries will be deleted
after confirmation
4. Speed Dial Set-up
Note: Phonebook should be set up first to activate speed dialing.
To set up speed dialing:
• Press Menu
• Scroll the menu by pressing or button until you see Quick Dial
• Press Send button
• Browse for an empty memory slot by pressing or button. There are
a total of 3 memory slots for speed dialing with each slot represented by the
, button and the Menu button
• Press the Menu button after finding an empty slot
• Browse the phone number that you wish to set to speed dial
• Press Send button to confirm
• Press End button to return to Main Menu
Note: If a memory slot is empty, user can simply press the desired key for 2
seconds then follow the above procedures.
13 14
To modify/delete speed dialing number:
Once you have saved a number for a slot/button, you need to delete it before
you can save a new number for that slot/button.
To delete a number in a speed dialing entry:
• Press Menu
• Scroll the menu by pressing or button until you see
Quick Dial
• Search for the entry that you would like to modify
• Press Menu button twice and the screen will show Delete ?
• Press Send button to confirm or End button to cancel
D. LCD Display
To adjust contrast of LCD Display:
• Press Menu
• Scroll the menu by pressing or button until you see Contrast Setting
• Press Send button to enter
• The status bar is shown in the contrast menu. This indicates the contrast level
of the LCD display
• Press the or button to adjust to desired contrast level
• Press Send button to save setting
E． Volume Adjustments
To adjust ring volume:
• Press the or button to adjust ring volume
To adjust call volume:
• Press the or button to adjust the volume during a call
To adjust microphone volume during a call:
• Press and hold Up button for two seconds to increase microphone volume
• Press and hold Down button for two seconds to decrease microphone
volume
If you cannot hear the person you are talking to on the other line, do the
following steps while conversation is in progress:
• Adjust the microphone volume of the YD-V16 to maximum level or
• Request the person on the other line to adjust his/her mobile phone’s
volume level to maximum
If there is a strong echo when the person on the other line talks:
• Transfer the call to your mobile phone
• If echo disappeared, transfer the call to your YD-V16 again and lower the
loud speaker volume until echo is reduced/eliminated
• If the echo remains, root cause of the echo might be with the network
provider or the mobile phone itself.
If the loudspeaker volume of the YD-V16 is too low or too high and you are
unable to adjust it:
• Adjust the volume directly on the mobile phone
• Fine tune it using the volume control of the YD-V16
15 16
Mute/Un-mute Functions
To mute the YD-V16 during an active call:
• Press Menu button for two seconds
To cancel mute:
• Press Menu button again
F. Call Operations
1. Making a Call
To make a call using the phone book:
• Press Menu button
• Press the or button until you see Contact list
• Press Send button to enter
• Select name by pressing the or button
• Press Send button to enter
• Press Send button again to dial
To call last number dialed:
• Press Send button
• Press the or button until you find the desired last dialed number
• Press Send button again to dial
To call using the speed dialing function:
• Press and hold the Menu button or the or button for 2 seconds
• Phone will automatically dial the number set to Speed Dial for that particular button
To make a call using the voice dialing function:
To enter voice dialing mode:
• Hold the Send button for 2 seconds
• Say the name after you hear the tone
Note: If the YD-V16 failed to recognize the voice/name. Press the End button
to exit and repeat the above steps for voice dialing.
Note: Voice Dialing is a feature of your mobile phone. Please refer to your
phone's user manual for voice command operation.
2. Answering Calls
To answer calls via the YD-V16:
• Press the Send button when ring tone is heard or
• Answer the call via the mobile handset
3. Ending Calls
To end a call:
• Press the End button or
• End call using the mobile handset
4. Rejecting Calls
To reject a call:
• Press the End button
17 18
7. Interchanging YD-V16 and Handset
You may interchange the call between your handset and YD-V16 while
conversation is ongoing
To shift from YD-V16 to handset or vice versa:
• Press and hold the Send button for two seconds
19 20
21 22
23 24
25 26
!
!
!
USB outlet
microphone
volume down
send
menu
end
status LED
volume up
DC jack outlet
caller ID screen
Power Switch Button
(end)
Phone Button
Go to Menu
Button Function Operation
CONTACT LIST
CONTRAST SETTING
DISCONNECT BT
QUICK DIAL
DELETE CONTACT
Pairing
Delete a number
saved in Quick Dial
Mute
Un-mute
DTMF (Dial Tone
Modulation Frequency)
Activated only when the line is connected
Transfer phonebook contacts from mobile phone
and SIM to YD-V16 via AT or OPP command
Press 1 time
Adjust LCD Contrast
Disconnect Bluetooth
®
With 3 memory slots for quick dialing
Delete entire phonebook content
Press and hold for 2 seconds
(Screen shows “Pair Mode”)
Press twice (screen will show “DELETE?”)
Press 1 time
Press 1 time
Welcome Screen
Bluetooth
®
Pairing Mode
Bluetooth
®
Pairing Successful
Blinking to indicate Bluetooth
®
Search Mode
Bluetooth
®
Disconnected
Outgoing Call
Incoming Call
Missed Call
Menu
Reception Signal Strength Indicator (for mobile phone only)
Call transfer to mobile during a call
Voice Dialing
Call Register (Outgoing Call/Incoming Call/Missed Call)
Volume Indicator
AT Command Inquire
AT Command Phone Book Transfer in Process
AT Command Phone Book Transfer Finished
OPP Phone Book Transfer in Process
Menu
Make / Receive call
Voice dialing
Conversation transfer
Bluetooth
®
link
connection
YES
End Call
Reject Call
No
Increase Volume
Scroll Upward
Move left
Increase Microphone
Gain
Decrease Volume
Scroll downward
Move right
Steady
Blinking (every 30 seconds)
Blinking (every 5 seconds)
Battery charging in progress
Battery low; recharging is recommended
Unit is powered on
Decrease Microphone
Gain
Button
LED Light
RED Light
BLUE Light
Status Indication
Function Operation
LCD Display Indication
Press 1 time
Press 1 time
Press 1 time
Press 1 time
Press 1 time
Press repeatedly until you reach desired volume level
Press repeatedly until you find desired
entry/menu item
Press repeatedly until you find desired
entry/menu item
Press and hold for 2 seconds
Press repeatedly until you reach desired volume level
Press repeatedly until you find desired
entry/menu item
Press repeatedly until you find desired
entry/menu item
Press and hold for 2 seconds
Press 1 time after pairing
Press and hold for 2 seconds to enter
voice dialing mode
While conversation is ongoing, press and hold
for 2 seconds
YD-V16
YD-V16
Pair Mode
Pair OK
Searching
NAME
NAME
1 Missed Call
Download Contact?
Downloading...
Downloading 1
Download Complete
Contact list
Bluetooth
®
Rearview Mirror Speakerphone
Car Charger
Velcro Straps
*For added safety, use Velcro straps
- Clip and attach the Velcro clips to the
back of the mirror (see above image)
- Loop the straps around the vehicle rearview mirror
- Press Velcro straps together to secure
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
To comply with FCC RF exposure requirements, the device and the antenna for this
device must be installed to ensure a minimum separation distance of 20cm or more
from a person's body. Other operating configurations should be avoided.
IC statement
Operation is subject to the following two conditions:
1) This device may not cause interference and
2) This device must accept any interference, including interference that may
cause undesired operation of the device.
This device has been designed to operate with an antenna having a maximum gain of 0
dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry
Canada. The required antenna impedance is 50 ohms.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures: