Bluetooth Module Datasheet Model: BLELED Module for Lighting kit BLELED Document Information 1 / 17 Title Module for Lighting kit Document type Datasheet Document number SL-18050051 Revision and date V4.
Bluetooth Module Datasheet Model: BLELED This document applicable to the following products： Product name Type number Product status Module for Lighting kit BLELED Mass Production 2 / 17 SKB360-DA-001,A/4
Bluetooth Module Datasheet Model: BLELED Contents 1 General Description ................................................................................................................................................4 2 Applications ............................................................................................................................................................4 3 Features..............................................................................................................
Bluetooth Module Datasheet Model: BLELED 1 General Description The BLELED is a highly integrated Bluetooth 4.2 BLE module, designed for high data rate, short-range wireless communication in the 2.4GHz ISM band. The module is based on Nordic nRF518xx radio Transceiver IC, has a 32 bit ARM Cortex-M0 CPU, Flash memory and analog and digital peripherals. The BLELED provides a low power and ultra-low cost BLE solution for wireless transmission applications.
Bluetooth Module Datasheet Model: BLELED 3 Features ◆ Main Chip: nRF518xx ◆ Bluetooth® 4.
Bluetooth Module Datasheet Model: BLELED 5 Interfaces 5.1 Power Supply Regulated power for the BLELED is required. The input voltage Vcc range should be 1.8V to 3.6V, current is not less than 20mA. Suitable decoupling must be provided by external decoupling circuitry (10uF and 0.1uF). It can reduce the noise from power supply and increase power stability. 5.2 System Function Interfaces 5.2.
Bluetooth Module Datasheet Model: BLELED Note：I2C:Inter－Integrated Circuit 5.2.3 Flash Program I/Os The module has two programmer pins, respectively SWDCLK pin and SWDIO pin. The two pin Serial Wire Debug (SWD) interface provided as a part of the Debug Access Port (DAP) offers a flexible and powerful mechanism for non-intrusive debugging of program code. Breakpoints and single stepping are part of this support. SWDIO can also be used as system reset pin, the system reset pin is active low. 5.2.
Bluetooth Module Datasheet Model: BLELED BLELED Pin Number Pin Name UART 16 P0.08 UART_TX 17 P0.09 UART_RX Pin Share UART(For Debug) Table5-3: UART Pin Share Scheme Note: The GPIOs are used for each SPI/TWI/UART interface line can be chosen from any GPIOs on the device and configed independently. 5.2.6 Analog to Digital Converter (ADC) The 10 bit incremental Analog to Digital Converter (ADC) enables sampling of up to 8 external signals through a front-end multiplexer.
Bluetooth Module Datasheet Model: BLELED module is input to a low level , the module will be automatically reset .After the reset pin is used , the parameters of the current setting will not be reserved . 6 Module Specifications Hardware Features Model BLELED Antenna Type PCB Antenna Chipset Solution nRF518xx Voltage 1.8V~3.6V Dimension(L×W×H) 17.4×13.7×1.9 mm Wireless Features Wireless Standards Bluetooth ® 4.2 Frequency Range 2400MHz---2483.
Bluetooth Module Datasheet Model: BLELED 7 Module Pinout and Pin Description 7.
Bluetooth Module Datasheet Model: BLELED 7.2 Pin Description Pin No. Pin Name Description Remark 1 GND Ground 2 VCC Main Power Supply 1.8V to 3.6V 3 P0.21 General Purpose I/O Digital I/O 4 P0.22 General Purpose I/O Digital I/O 5 P0.23 General Purpose I/O Digital I/O 6 P0.24 General Purpose I/O Digital I/O 7 P0.25 General Purpose I/O Digital I/O 8 P0.28 General Purpose I/O Digital I/O 9 P0.29 General Purpose I/O Digital I/O 10 GND Ground 11 P0.
Bluetooth Module Datasheet Model: BLELED 8 PCB Design Guide Please reserve empty area for PCB antenna when you are going to design a board, the empty range device’s minimum size :16.5*6.6mm , please kindly check the “PCB footprint and Dimensions” for reference.
Bluetooth Module Datasheet Model: BLELED 10 Electrical Characteristics 10.1 Absolute Maximum Ratings Parameter Condition Storage Temperature Range Min. Typ. Max. Unit -40 85 °C ESD Protection VESD / 4000 V Supply Voltage VCC -0.3 3.9 V -0.3 3.63 V Voltage On Any I/O Pin Table10-1: Absolute Maximum Ratings Note: Absolute maximum ratings are stress ratings only, and functional operation at the maxims is not guaranteed.
Bluetooth Module Datasheet Model: BLELED 10.2 Recommended Operation Ratings Parameter Symbol Min. Extended Temp. Range TA -25 Power Supply VCC 1.8 Input Low Voltage VIL Input High Voltage VIH Typ. Max. Unit 75 ºC 3.6 V 0 1 V 2.3 3.9 V 3.3 Table10-2: Operating Conditions 10.3 Current System State Current (peak)@3V TX Peak @0dBm RX Peak 10.5 mA 13 mA Advertise Interval @100ms (0dBm)(avg) Sleep Mode （avg） Idle Mode (avg) 270uA 0.28uA 2.
Bluetooth Module Datasheet Model: BLELED Exceeding the maximum soldering temperature in the recommended soldering profile may permanently damage the module. 12 Ordering Information Module No. Type number Chipset Certification BLELED 09192 nRF51822 RoHS, FCC, CE BLELED 0919204 nRF51802 RoHS, FCC, CE 13 Packaging Specification BLELED modules are put into tray and 528 units per tray. Each tray is ‘dry’ and vacuum packaging.
Bluetooth Module Datasheet Model: BLELED 14. FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT.
Bluetooth Module Datasheet Model: BLELED 14 Revision History 17 / 17 Revision Description Approved Date V1.01 Initial Release Sunny 20140611 V2.01 Upgrade Hardware Sunny 20150117 V2.02 Add AT Instruction Sunny 20150528 V2.03 Upgrade hardware Hogan 20160611 V3.01 Upgrade format Hogan 20161211 V3.02 Upgrade product image Hogan 20170504 V3.03 Update certification information George 20170831 V4.01 Add order information George 20180209 V4.
