UHF RFID Reader/Reader Module DEMO Software User Manual V1.1 Winnix Technologies Co.
www.winnix.net Content Content………………………………………………………….…………………………………………….………2 1. Introduce………………………………………………….…………………………………………….………3 2. User Guide……………………………………………………………………………….……………….……3 2.1 Language……………………………………………………………………………….……….……3 2.2 Connection………………………………………………………………………..…………….……4 2.1.1 Ethernet connection……………………………..…………………………………….…4 2.1.2 RS232 connection……………………….……………………………………………….…4 2.3 Single inventory operation……………………………….……………………..………….…5 2.4 Multiple inventory operation…………………………….
www.winnix.net 1. Introduce The Demo software user manual is used for HYM730/HYM740/HYM750 serial modules and HYR810/HYR820/HYR830 series readers; Support Chinese and English language; Support RJ45 connecting. Adopt TCP long connection method, slave computer as TCP server, host computer demo software as the TCP client side. (Notice: RJ45 connecting only for HYR830 reader) Support RS232 connecting, baud rate 115200, 1 bit for start, 1 bit for stop, 8 bits for data. 2. User Guide 2.
www.winnix.net 2.2 Connection Demo software support two optional connecting, Ethernet and RS232 serial connections. 2.2.1 Ethernet connection setting Default IP address of the reader is 192.168.1.10. If connecting in Ethernet (RJ45), please set IP address of PC at same range, such as 192.168.1.100. Before connecting, make sure IP address of PC could be passed at Ping operation. Connections are displayed with different prefix. If connecting with RJ45, type ‘NET’+’IP’ at the drop-down box of port.
www.winnix.net to do is to choose correct COM number, and then it should be connected, as below picture. Picture 4 RS232 port connection 2.3 Single inventory operation Single inventory operation is in ‘singe ask’ and ‘single answer’ method of reading. Each inventory will result an acknowledgement frame. In each single inventory, only one tag’s EPC data could be gotten. Single inventory mode supports to inventory tag function at any length EPC code.
www.winnix.net Picture 5 Single inventory mode 2.4 Multiple inventory operation Below picture is for multiple inventory mode. Inventory times are non-limited. At information area, it will display Inventory speed, time and tag numbers. Click ‘off-line clean’, it will launch the function. If a tag is not read in 4 seconds, the marked color of the tag will turn grey, if over 8 seconds, the tag will be cleared from workspace.
www.winnix.net Picture 6 Multiple inventory mode 2.5 RF output power setting TX power setting is in basic settings section, below picture is for TX power setting. Picture 7 RF output power setting The TX power range is 5-30dBm, with 1dBm stepping up. ‘Set’ the picked power, and then ‘get’ for checking the result. Choose "save", the setting will be kept after power off. 2.6 Region setting Region setting is in basic settings section, as below picture.
www.winnix.net Region setting includes China1 area (840.625MHz~844.375MHz), China2 area (920.625MHz~924.375MHz), Europe area (865.7MHz~867.5 MHz), USA area (902MHz~928MHz), Korea and Japan area. Choose the frequency band at your area, and then click ‘set’, ‘get’ is to check the current band you have chosen. Choose "save", the setting will be kept after power off. 2.7 Frequency hopping setting Frequency hopping setting is in basic settings as below picture.
www.winnix.net Picture 11 Temperature information Click ‘get’ to see the working temperature information. For normally, the temperature range is between -40 – 85 degree Celsius. When the “temperature protect” is activated (the default is turn on), once the temperat ure is over 65℃, the rate of inventory would fell by 50%; If the temperature is over 85℃, the reader-module would stop working automatically, and it would back to work again only the temperature below 85℃.
www.winnix.net Picture 14 Multiple inventory Delay time setting The setting is for module waiting time after one inventory cycle during the multiple inventory working. This is only applied for single port module. Default value is 0 during multiple inventory. At such case, the module will be working at full load, while the module temperature will be higher. 2.13 Antenna working and interval time setting Antenna working and interval time setting is in Basic Setting, as below picture.
www.winnix.net 2.15 GPIO setting GPIO setting is in Basic Setting as below picture. Picture 17 GPIO setting Notice: HYM series modules only have 3 output IO ports (GPIO1, GPIO2 and GPIO3). HYM830 reader has 4 output IO ports (GPIO1, GPIO2, GPIO3, GPIO4), and 4 input IO ports (GPIO5, GPIO6, GPIO7, GPIO8) The picked output IO ports will output high level, otherwise will output low level.
www.winnix.net Picture 20 Q setting There are two ways of dynamic Q and static Q. Dynamic Q is recommended, as it could automatically adjust the Q value to achieve most fast inventory. 2.19 Single inventory timeout setting In Advanced Settings section, below is the picture for single inventory timeout setting Picture 21 Single inventory timeout setting This function is only for single inventory. If single read is unsuccessful, after the overtime, the reader will report the result.
www.winnix.net Picture 23 Tag reading and writing setting Memory Bank is data area of the tag, which includes RFU, EPC, TID and USR.RFU is for password zone of the tag, including Access Password (AccPwd) and Kill Password (Killpwd). EPC is the ID number of the tag, usually at 12 bytes. TID is the worldwide sole ID code, and includes the information of tag IC company. USR is data zone for users, for some kind of tag there is no the USR data zone.
www.winnix.net 2.23 Tag Kill setting In Tag Operate section, below is the picture for Tag Kill setting. Picture 25 Tag kill setting It is supported by ISO18000-6C protocol the reader could kill the tags permanently. Please caution the killed tag could not be usable. Tag Kill setting is usually operated with filter operation, which means you can kill the picked EPC tags, and avoid killing un-picked tags.
www.winnix.net 2.
OEMs information: RealID Technology Co., Ltd. was established in December 2012, the registered capital of 990 million yuan. It is a professional company specializing in RFID system design, equipment development and related technical services. RealID Technology Co., Ltd. gathered a number of highly qualified management personnel, first‐class product development elite, to provide customers with first‐class hardware products, program design, and custom services.
undesired opera on. Manual Requirements according 15.21 Changes or modif ca ons made to this equipment not expressly approved by (manufacturer name) may void the FCC authorization to operate this equipment. Declaration 1) Marketing The device must be sold to dealers. 2) Professional installation Installed by licensed professionals ( EUT sold to dealer who hire installers) 3) Application The intended use is generally not for the general public. It is generally for industry/commercial use.
