EZCast TwinX C-1 Wireless Display Transmitter Quick Start Guide Rev 1.0 Product information is subject to change without prior notice.
How to mirror 1 Simply plug into laptop or mobile Plug EZCast TwinX C-1 to Type C port on laptop or mobile. Wait a few seconds until the flashing light on EZCast TwinX stops, and it will start mirroring automatically. Please make sure to insall and pair to EZCast wireless display receiver if flashing over 20 seconds. 2 Stop and restart mirroring Press the EZCast TwinX button to stop mirroring or restart mirroring.
How to pair EZCast TwinX with receiver 1 Turn on pairing mode for receiver Press the reset button (or insert the pin to press) for 2 seconds on EZCast wireless display receiver. Release the button when the screen shows “Release the button to pair with EZCast”. Please make sure your receiver has been upgraded to the latest version. Note: All EZCast wireless display receiver on our website supports EZCast TwinX pairing, except for Magic series products.
EZCast TwinX C-1 無線顯示發射器 快速指南 Rev 1.
如何鏡像 1 接上電腦或手機即可開始投影 將EZCast TwinX接上電腦或手機的Type C接口,等待數秒至EZCast TwinX的閃燈停止,即開始自動投影。若閃燈持續超過20秒,請確 保EZCast無線顯示接收器已正確安裝並配對至EZCast TwinX。 2 停止/重新鏡像 點擊EZCast TwinX上的按鈕,可停止或重新鏡像。 注意:EZCast TwinX支援Windows/ MacOS電腦,以及支援 DP輸出的Android手機。 1
如何配對接收器 1 開啟接收器配對模式 長按EZCast無線顯示接收器上的按鈕(或拿針戳進重置孔)2秒左 右,待畫面顯示文字“Release the button to pair with EZCast”時 放開按鈕。請確保無線顯示接收器已更新至最新版本。 注意:官網上所有無線顯示接收器,除Magic系列之外,皆支援 EZCast TwinX配對。 2 secs 或 Release the button to pair with EZCast 2 按下EZCast TwinX的按鈕 將EZCast TwinX C-1接上電腦或手機供電,在畫面顯示“Ready to pair”時按下EZCast TwinX上的按鈕即完成配對。 Ready to pair 注意:無線顯示接收器上的重置孔,根據按壓時間不同,有三種 設定模式。 (1) 按壓一下:切換接收器的Wi-Fi模式為2.
EZCast TwinX C-1 无线显示发射器 快速指南 Rev 1.
如何镜像 1 接上电脑或手机即可开始投屏 将EZCast TwinX接上电脑或手机的Type C接口,等待数秒至EZCast TwinX的闪灯停止,即开始自动投屏。若闪灯持续超过20秒,请确 保EZCast无线显示接收器已正确安装并配对至EZCast TwinX。 2 停止/重新镜像 点击EZCast TwinX上的按钮,可停止或重新镜像。 温馨提示:EZCast TwinX支持微软、苹果电脑,以及支持DP输 出的安卓手机。 1
如何配对接收器 1 开启接收器配对模式 长按EZCast无线显示接收器上的按钮(或拿针戳进重置孔)2秒左 右,待画面显示文字“Release the button to pair with EZCast”时 放开按钮。请确保无线显示接收器已更新至最新版本。 温馨提示:官网上所有无线显示接收器,除Magic系列之外,皆支 持EZCast TwinX配对。 2 secs 或 Release the button to pair with EZCast 2 按下EZCast TwinX的按钮 将EZCast TwinX C-1接上电脑或手机供电,在画面显示“Ready to pair”时按下EZCast TwinX上的按钮即完成配对。 Ready to pair 温馨提示:无线显示接收器上的重置孔,根据按压时间不同,有 三种设定模式。 (1) 按压一下:切换接收器的Wi-Fi模式为2.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.