Outdoor Enterprise Access Point WM-OAP8251AG Quick Start Guide V1.0 For more information on this and other Winmate products, please visit our website at: www.winmate.com Document Part Number: 91521110100L Please read these instructions carefully before using this product, and save this manual for future use.
FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Contents GETTING STARTED 1 Features 1 Package Contents 2 Minimum Requirements 2 Product Overview 3 INSTALLATION 5 Connecting the Access Point 5 Managed Access Point with Wireless Management Switch 5 Stand-alone Access Point Installation 6 Mounting 7 Wall Mounting the AP 7 Pole Mounting the AP 8 GETTING STARTED 10 Configuring Your Access Point 10 Default Settings 10 Web Configuration 10 iii WM-OAP8251AG Quick Start Guide
GETTING STARTED Congratulations on purchasing Winmate® Outdoor Enterprise Access Point. The WM-OAP8251AG is an enterprise class, outdoor dual radio 2.4G (11n) and 5G (11ac Wave2) concurrent 4x4 MU-MIMO access point with built-in internal antenna. The device has two Ethernet ports and one of it is a PSE port that supplies power to the remote unit. With certified IP67 protection, Winmate® Outdoor Enterprise Access Point is designed to deliver high reliability under harsh outdoor environment.
Package Contents Carefully remove the box and unpack your device. Please check if all the items listed below are inside your package. If any of these items are missing or damaged contact us immediately. The factory shipment list: Outdoor Enterprise Access Point WM-OAP8251AG Quick Start Guide (Hardcopy) User Manual EzMaster Software & User Manual PoE Injector Wall Mounting Kit Pole Mounting Kit Mounting Screws and Bolts Ground Cable (Green) AWG10 180cm Power Adapter Power Cable 2.
Product Overview Unit dimensions (L x W x H): 210mm x 210mm x 51mm Weight: 1.5 kg Front View No. Description 1 2.4 GHz Antennas: Detachable 5 dBi 2.4 GHz omni-directional 2 5 GHz Antennas : Detachable 7 dBi 5 GHz omni-directional 3 LAN Port 1 (802.3at PoE Input): Ethernet port for RJ-45 cable. 4 LAN Port 2 (802.3af PSE Output): Ethernet port for RJ-45 cable. 5 Console/ Reset: Console panel/ reset button. 6 LED Indicators: LED lights for Power, LAN Port 1, LAN Port 2, 2.
Rear View No. Description 6 Ground 7 Mounting Holes: Using the provided mounting kits, the WM-OAP8251AG can be attached to a wall or pole.
INSTALLATION Connecting the Access Point Managed Access Point with Wireless Management Switch This diagram depicts the hardware configuration. Follow the instructions below to establish the connection to the Access Point. A. Connect one end of the Ethernet Cable into the main LAN Port (PoE) of Managed Access Point and the other end to the Ethernet Port on the Wireless Management Switch. B.
Stand-alone Access Point Installation Follow the instructions below to establish the connection to the Access Point. A. Connect one end of the Ethernet Cable into the main LAN Port (PoE) of the Access Point and the other end to the AP Ethernet Port. B. Connect the Power Adapter to the DC-IN port of the PoE injector and plug the other end into an electric outlet. C. Connect the second Ethernet cable into the LAN port of the PoE injector and the other end to the Ethernet port on the computer. D.
Mounting Wall Mounting the AP To attach the WM-OAP8251AG to a wall using wall mounting kit: A. Mark the four locations of the mounting holes on the flat mounting surface. B. Drill a 37 mm deep 8 mm hole in the markings and hammer the bolts into the openings. C. Place the lock and flat washers on the four hex cap screws and drive the screws to attach the bracket to the back of the Access Point.
Pole Mounting the AP To attach the WM-OAP8251AG to a wall using pole mounting kit: To attach the WM-OAP8251AG to a wall using provided pole mounting kit: A. Attach the device onto the wall by tightening the bolt’s flat washers and nuts to secure the mounting base to the mounting surface. B. Drive the four round head screws to attach the Pole Mount Bracket to a Wall Mount bracket.
C. Thread the open end of the Pole Strap through the two tabs on the Pole Mount Bracket. D. Lock and tighten the Pole Strap to secure the Pole Mount Bracket to the pole.
GETTING STARTED Configuring Your Access Point Before you begin, the device must be able to communicate with the ezMaster server for ezMaster to manage an AP or switch. Make sure that the ezMaster server, EWS AP and EWS switch can all be reachable via HTTP/HTTPS from outside your internal network. For more information about ezMaster server settings, refer to the ezMaster Quick Start Guide included in the package.
If successful, you will be logged in and see the WM-OAP8251AG User Menu.
NOTES ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ___________________________________________________
Winmate Inc. 9F, No.111-6, Shing-De Rd., San-Chung District, New Taipei City 24158, Taiwan, R.O.C Tel: 886-2-8511-0288 Fax: 886-2-8511-0211 Email: sales@winmate.com.tw Official website: www.winmate.
