Windy Plus Box PC Windy Plus Box PC for Vehicle Producing Examination USER MANUAL Version: 1.0 Attention!!! This product is designed for vehicle producing examination only. It should be used in vehicle production line and required to be away from operator >30cm when operating.
Windy Plus Box PC TABLE OF CONTENTS CHAPTER 1 READ ME FIRST........................................ 3 IMPORTANT SAFETY INSTRUCTIONS ........................................................................ 4 Copyright Notice ......................................................................................................................... 5 Warranty .................................................................................................................................... 5 Customer Service ..
Windy Plus Box PC CHAPTER 1 Read Me First User Manual Windy Plus
Windy Plus Box PC Attention!!! This product is designed for vehicle producing examination only. It should be used in vehicle production line and required to be away from operator >30cm when operating. IMPORTANT SAFETY INSTRUCTIONS Please read these instructions carefully before using the product and save for later reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Clean the product with a damp soft cloth.
Windy Box PC Copyright Notice Copyright © 2008 Winmate Communication Inc., ALL RIGHTS RESERVED. No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners. Disclaimer Winmate Communication Inc.
Windy Plus Box PC Customer Service We provide service guide for any problem as follow steps：First, visit the website at http://www.winmate.com.tw to find the update information about the product. Second, contact with your distributor, sales representative, or our customer service center for technical support if you need additional assistance.
Windy Plus Box PC CHAPTER 2 Getting started User Manual Windy Plus
Windy Plus Box PC CHAPTER 2 GETTING STARTED Congratulations for you to purchase this rugged box computer. This chapter tells you step by step how to boot up the box computer. You can find instructions for the following procedures: Connecting the AC Power Our box PC can operate either on the external AC power adapter or internal battery power. It is suggested that you use AC power when you boot up the box PC first time. Caution !!! Use only the AC adapter included with your box PC.
Windy Plus Box PC when is fully charged. Boot up and shut down the Windy Boot up the Windy 1. Put your Windy on a flat and stable surface or holding the Windy on your hand. 2. Make sure that the Windy is either connected to AC power or the battery pack with power. 3. Press the power button by 3~4 seconds to boot it up. Shut down the Windy To turn off the Windy power, click the “Shut Down” command of your operating system.
Windy Plus Box PC How to wake up Windy by TX box When the Windy is in S3 or S5 mode, you can wake it up with a TX box (optional). Please follow the steps list below to apply this function. 1. Set the Windy from working state (S0) into sleep state (S3) or Soft Off state (S5) 2. Take out the TX box and connect it to power source (5V DC in). 5V DC in 3. Aim the IR receiver (either of three) on Windy with TX box. From distant location (<10m), please push the button on top of TX box.
Windy Plus Box PC DIP switch Product Overview User Manual Windy Plus
Windy Plus Box PC Diagram of front view LED Indicator (Defined & Controlled by customer) IR receiver I/O protect cover Suction cup Diagram of Side view OBD connector (VGA type) Diagram of Rear view Epaper Didplay LED Indicator (Defined & Controlled by customer) Microphone User Manual Battery cover Handle Windy Plus
Windy Plus Box PC Diagram of I/O view IR receiver RJ45 VGA output USB 3.0 19V DC in Instruction of OSD & LED Status Indication LED Status Indication Power button LED Status Indication Description LED Term Power mode LED Indicator Indicator Status Description Green light：Power On No light : Power Off No light：Charge completely or Normal using (>10%) Battery Status Orange Light： Under charging Red Light Blinking：Low Battery (<10%) Storage \\\Status User Manual Green light：Storage operating
Windy Plus Box PC Wi-Fi Status Green light：Wi-Fi operating No light User Manual : Wi-Fi suspend Windy Plus
Windy Plus Box PC Product Specification The product specification(default) as the following table description: System Main board Spec Processor Intel® Pentium® Processor N4200 1. 1GHz, turbo up to 2.5GHz BIOS Insyde System BIOS System Memory 1 x 8GB SODIMM DDR3L-1866 (Max 8GB) LAN Controller Intel I210 Storage 1 x M.2 2242 Key B 256GB SSD, 1 x M.
Windy Plus Box PC Product Specification (continue) Mechanical and Environment Weight Operating Temperature 1.3 Kg (w/o accessories) -10℃~50℃ Operating Humidity 10% to 95% (non condensing) Mounting Suction cup with handle Shock MIL-STD-810G M516.6 (By request) Vibration MIL-STD-810G M514.6 (By request) Drop 4 ft, Free to concrete Certifications CE, CE Wi-Fi, FCC, CCC Power Management Power Input 19V DC in Battery Li-Ion battery 3000mAh, 7.
Windy Plus Box PC CHAPTER 3 Useful Information User Manual Windy Plus
Windy Plus Box PC To implement the process of function test or BIOS update, you have to use VGA connector to show the Windy's output to a display (Resolution will be adjusted automatically). 1. The procedure to test connecting with OBD BOX 1.1 After running the program, please select the "P-Module VBat Test".
Windy Plus Box PC 1.2 Click all the testing Item sequentially. It will show green when it Pass, but red when Fail. 1.3 After all the test has been done, please click the "EXIT” icon.
Windy Plus Box PC 2. The procedure to update bios of MCU 2.1 Open “MCU AP” folder and run “SerialBootloaderDataSource.exe” 2.2. a. Click “Select Hex File(s)” c. Click “Open” b. Click .hex file d. Run the Hex file successfully as follow.
Windy Plus Box PC 2.3 a. Click “COM Port” b. Click “Open COM Port” ※Please do not close the whole program window. 2.4 Run ”DaimlerMCUControl.exe” 2.
Windy Plus Box PC 2.6 If the program shows the notice “Click the ‘Update Application Firmware’ button to continue ” ,please click ”Update Application Firmware” . 2.7 When the message ”Bootload process completed successfully!” appears in the columm, it means update boot loader process was fully completed.
Windy Plus Box PC 3. The procedure to test all the Wake up function 3.1 IR Wake up a. Implement Daimler MCU Control and perform COM Port Connect to COM3 then set IR Enable. b. Click Get IR Wake and make sure IR Wake Status=Enable c. Let the system to Sleep / Hibernate / Shout down Mode, then use the TX BOX to wake Windy up and get event to confirm which IR worked. d. Click Get IR Table and make sure if it has count, the information of time and ID need to be correct.
Windy Plus Box PC 3.2 OBD In Wake up a. Implement Daimler MCU Control and perform COM Port connect to COM3 then set OBD In Enable. b. Click Get OBD In and make sure OBD In Wake Status=Enable。 c. Allow the system to enter the Sleep / Hibernate / Shout down Mode and plug in the OBD cable to wake up the Porty G3 S. Click get Event to confirm whether wake up by OBD In. d. Click OBD In Setting make sure whether the count and time information are correct.
Windy Plus Box PC 3.3 OBD Out Wake up a. Implement Daimler MCU Control and perform COM Port connect to COM3 then set OBD out enable. b. Click Get OBD Out and make sure OBD Out Wake Status=Enable。 c. Allow the system to enter the Sleep / Hibernate / Shut down Mode and un-plug the OBD cable to wake up the Porty G3 S. Click get Event to confirm whether wake up by OBD Out. d. Click OBD Out settings and make sure whether the count and time information are correct.
Windy Plus Box PC 3.4 Button Wake up a. Implement Daimler MCU Control and perform COM Port connect to COM3 then set Button out enable b. Click Get Button settings and make sure Button Wake Status=Enable。 c. Allow the system to enter the Sleep / Hibernate / Shut down Mode and press the power button to wake up the Porty G3 S. Click get Event to confirm whether wake up by Button. d. Click OBD Out setting make sure whether the count and time information are correct.
Windy Plus Box PC 3.5 RTC Wake up a. Implement Daimler MCU Control and perform COM Port connect to COM1 then set RTC enable. b. Click Get RTC Wake and make sure RTC Wake Status=Enable. c. Click on the Time Sync and allow time synchronization d. Click Get Time, confirm the time is synchronized e. Set Alarm Time in order to set the wake-up time. f. Allow the system to enter the Sleep / Hibernate / Shut down Mode and after a specified time to wake up Windy Plus.
Windy Plus Box PC correct. h. You can choose Year/Month/Day/Hour/Minute in Alarm Repeat Mode. 3.6 Docking In Wake up a. Implement Daimler MCU Control and perform COM Port connect to COM1 then set DC In enable. b. Click Get Docking In Wake and make sure Docking in Wake Status=Enable。 c. Allow the system to enter the Sleep / Hibernate / Shut down Mode and plug in the power adapter to wake up the Windy Plus, Click get Event to confirm whether wake up by DC Power In. d.
Windy Plus Box PC 3.7 Docking Out Wake up a. Implement Daimler MCU Control and perform COM Port connect to COM1 then set Docking Out enable. b. Click Get Docking Out Wake and make sure Docking Out Wake Status=Enable. c. Allow the system to enter the Sleep / Hibernate / Shut down Mode and unplug the power adapter to wake up the Windy Plus. Click get Event to confirm whether wake up by DC Power Out. d. Click Get Docking Out Table and make sure whether the count and time information are correct. 3.
Windy Plus Box PC User Manual Windy Plus
Windy Plus Box PC CHAPTER 4 User Manual Troubleshooting Windy Plus
Windy Plus Box PC Troubleshooting Problem The removable battery is not charging. Solution Make sure the AC adapter is properly connected, and that the removable battery is properly inserted. Nothing appears on the output display. The Windy may be in sleep mode. Press the power button to wake it up. Wireless LAN signal quality is poor. The Windy may be out of wireless sufficient range. Move the Windy to be more closer to the access point.
Windy Plus Box PC Winmate INC. 9F, No.111-6, Shing-De Rd., San-Chung District, New Taipei City 241, Taiwan, R.O.C Web Site: http://www.winmate.com.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
