Installation Manual Automatic Multi-Satellite TV Antenna Model SK-7003 TRAV’LER® Shaw Direct Antenna www.winegard.com/mobile For Technical Services, email help@winegard.com or call 1-800-788-4417 Product Registration Please register your Winegard product by filling out and returning the Product Registration Card provided or by completing the online registration form at http://www.winegard.com/registration.
Before Installing the Antenna You have selected the Winegard® TRAV’LER® automatic multi-satellite TV antenna. The TRAV’LER antenna will deliver the ability to view multiple satellites at the same time with unmatched signal strength, the lowest travel height on the market, maximum HD capabilities and easy to use functionality—just like you get at home. This manual provides important information on the installation and operation of your TRAV’LER antenna on an RV.
Clearance Requirements The arm of the TRAV’LER antenna extends 33” from the center of the base and may operate only 6” above the surface to which the TRAV’LER antenna is mounted. To ensure you have adequate clearance for the TRAV’LER antenna to safely operate, check that there are no obstructions taller than 6” within 33” of the center of the base. Also, check that there are no obstructions (such as tree limbs) above the antenna that will prevent it from raising.
Choosing a Location for the Antenna 1. For best performance and to reduce signal acquisition time, park the vehicle on a level surface that is free of obstructions such as trees or large buildings. Make sure you have a clear view of the southern sky. 2. Before removing the TRAV’LER antenna from its box, contact your RV dealer or manufacturer. Your RV may be prewired or have a reinforced area for this system. 3. Then, choose a location on the roof that meets the following requirements: a.
Installing the Antenna 1. Place the TRAV’LER antenna on the roof where you plan to install it. On the mount base, the transition plate is marked “FRONT” and “BACK.” Rotate the TRAV’LER antenna until the front of the mount base faces the front of the RV. The TRAV’LER antenna must be installed on or parallel to the centerline of the coach. See figure 6. No obstructions taller than 6″ in a 33″ radius Mount on or parallel to Centerline of RV 33″ Front of RV Centerline of RV FIGURE 6.
Installing the GPS Antenna The GPS antenna is connected to the TRAV’LER antenna via a 6’ cable running to port E on the TRAV’LER mount base. 1. To install the antenna, find an open area at least 18” from either side of the mount base. 2. Place a small dot of sealant at the chosen location for the GPS antenna. 3. Place the GPS antenna on the sealant, and press the antenna into place. 4. Secure any excess cable. Do not cut the GPS cable. Overall Setup 1.
Installing the Reflector, LNBF, & Feed Arm Note that the reflector, LNBF, and feed arm are packaged separately as SKA-733. 1. Press and hold “POWER” for two seconds to turn on the interface box. Wait until the interface box finishes “connecting to antenna.” The TRAV’LER® antenna may enter the search routine after ten seconds. Pay attention to the pinch points as the antenna raises! 2. Wait until the antenna has at least raised to a position in which the lift arms are perpendicular to the roof.
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY (2 YEARS PARTS; 1 YEAR LABOR) Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products.
Operation Manual Automatic Multi-Satellite TV Antenna Model SK-7003 TRAV’LER® Shaw Direct Antenna www.winegard.com/mobile For Technical Services, email help@winegard.com or call 1-800-788-4417 Product Registration Please register your Winegard product by filling out and returning the Product Registration Card provided or by completing the online registration form at http://www.winegard.com/registration.
Automatic Operation The TRAV’LER antenna offers a simple one-button operation. Simply press “POWER,” and the antenna will automatically begin searching for satellites. The instructions assume that the antenna is already in the stowed position. 1. Press and hold “POWER” for two seconds or until the TRAV’LER interface displays “POWER ON.” 2. Once the unit has been powered on, release “POWER.” connecting to WINEGARD COMPANY POWER ON 4.
Manual Operation The TRAV’LER antenna is a versatile satellite antenna and can be manually set to find many different satellites individually. This function is rarely used. The instructions assume that the antenna is already in the stowed position. Note: Diagnostics and Installation menus are not required for normal operation and should only be entered by a trained professional. 1. Press and hold “POWER” for two seconds or until the TRAV’LER interface displays “POWER ON.
To initiate a signal refresh, call 1-888-554-7827, then select “Self-Serve”, “Technical Support”, followed by “Signal Refresh” from the telephone menu options. For changes to Shaw Direct programming or to purchase new Shaw Direct equipment, visit shawdirect.ca or call 1-888-554-7827. Note that the TRAV’LER antenna will find the satellites without the receiver installed. Troubleshooting ANTENNA CONNECTION FAILED Check the data cable connection on the back of the interface box.