Installation Manual

ManualsBrandsWinegard ManualsAccessories & SuppliesWinegard RVW-395 Sensar IV White DTV/HD TV Antenna

WINEGARD

INSTALLATION/OPERATION MANUAL (All Models)

MADE IN U.S.A.

(Sensar

III head - U.S. Patent D500,496)

(WINGMAN

- U.S. Patent D612,369)

(Sensar

IV head - U.S. Patent D620,483)

WINEGARD

SENSAR

ANTENNAS

• Increases UHF performance up to 100%

• FREE digital programming

• Installs in minutes -

no tools required

•RV-WING – White, RV •GS-WING – Gray, Residential

Sensar only Sensar with

Wingman

VHF UHF VHF UHF

Excellent

Digital

Reception

Great

Digital

Reception

Digital Reception

Sensar vs Sensar with Wingman

Channels

14-51

Channels

2-13

Channels

14-51

Channels

2-13

SENSAR

III ANTENNA

SENSAR

III ANTENNA

WITH WINGMAN

ACCESSORY

Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601-2000 © Winegard Company, 2004, 2006 2452013 REV9 5/13

SENSAR

ANTENNA

WITH WINGMAN

®-

SENSAR

IV ANTENNA

Summary of content (8 pages)

PAGE 1
WINEGARD® WINEGARD SENSAR ANTENNAS ® ® INSTALLATION/OPERATION MANUAL (All Models) MADE IN U.S.A. (Sensar® III head - U.S. Patent D500,496) (WINGMAN® - U.S. Patent D612,369) (Sensar® IV head - U.S.
PAGE 2
STEP 1: Choose location for antenna. Figure 1 illustrates placement of the Sensar, showing it in travel position. You must be able to raise and rotate antenna without interfering with other roof-mounted equipment. Make sure inside ceiling area is clear to mount ceiling plate. NOTE: Maintain a minimum of 10" from the edge of the roof or any obstruction (16" must be maintained if installing a Sensar IV).
PAGE 3
FIGURE 6 ALL MODELS STEP 6: Attach antenna head to lift tubes with two (2) steel pins, Figure 6. Align holes in leveling bracket on back of antenna head with holes in lift tubes, insert pins and secure in place with (2) E-clips. Use pliers and get a firm grip on E-clips. Fit clips into groove on pins and snap into place.
PAGE 4
AMPLIFIED MODELS ONLY STEP 11: Select location for wall plate. Run two coax cables (RG-6 type recommended) (three if set 2 jack is going to be used) between locations and install connectors on each end. Mark cables so "cable input", "TV output" "Set 2" may be identified. Antenna downlead and filtered 12 VDC power source will also be needed at inside wall plate/power supply location. FIGURE 10 STEP 12: The wall plate/power supply assembly may be flush mounted in most standard electrical boxes.
PAGE 5
WINEGARD SENSAR ANTENNAS ® ® OPERATION MANUAL (All Models) LUBRICATION (Done 3-4 times annually) STEP 1: To lubricate the elevating gear, apply a liberal amount of silicone spray lubricant to the elevating gear with the lift in the down position (see illustration). Run the lift up and down to distribute the lubricant over gears.
PAGE 6
INSTALLING F-CONNECTORS ON COAXIAL CABLE Step 1. Strip outer cover back 1/2"* from end of cable. Fray braid back as far as outer cover will allow. Step 2. Trim braid close to outer cover and remove 1/4"* of inner insulation being careful not to nick center conductor. Make sure no foil or braid can touch center conductor. Step 3. Slide connector tip between braid and inner insulation (braid and foil, on foil shield cable) and push connector on cable as far as it will go.
PAGE 7
ORDERING REPAIR PARTS Repair parts are available at many RV dealers and/or service centers throughout the country. If you don't have a dealer/service center near you, call Winegard Company at 1-800-288-8094. All major credit cards accepted. Parts are available only in the packages shown here. Order by the Model No. of the package needed. Example: To order the elevating gear, order RP-3000. Tax, shipping and handling additional. PACKAGE 1 MODEL NO.
PAGE 8
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY (2 YEARS PARTS; 1 YEAR LABOR) Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products.