User's Manual

ManualsBrandsWilson Electronics ManualsAmplifiersMobile Wireless Single Band Amplifier

Amplifier

Installation

Guide

Mobile Wireless

Single Band

Cellular

Amplier

PART/MODEL# 801101

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1

How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2

Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3

Installing a Wilson Outside Antenna · · · · · · · · · · · · · · · 4

Installing a Wilson Amplier · · · · · · · · · · · · · · · · · · · · · · 5

Installing a Wilson Inside Antenna (Wireless) · · · · · · · · 6

Installing a Wilson Inside Antenna (Attached) · · · · · · · · 7

Powering Up a Wilson Amplier · · · · · · · · · · · · · · · · · · · 8

Warnings and Recommendations · · · · · · · · · · · · · · · · · 9

Understanding the Amplier Lights · · · · · · · · · ·· · · · · · · 10

Amplier Specications · · · · · · · · · · · · · · · · · · Back Cover

Wilson

Electronics, Inc.

Warning: This manual contains

important safety and operating information.

Please read and follow the instructions

in this manual. Failure to do so could be

hazardous and result in damage to your

amplier.

Summary of content (12 pages)

PAGE 1
Amplifier Installation Guide Mobile Wireless Single Band Cellular Amplifier PART/MODEL# 801101 Contents: Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1 How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3 Installing a Wilson Outside Antenna · · · · · · · · · · · · · · · 4 Installing a Wilson Amplifier · · · · · · · · · · · · · · · · · · · · · · 5 Installing a Wilson Inside A
PAGE 2
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson’s 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 1-Year Warranty Wilson Electronics amplifiers are warranted for one (1) year against defects in workmanship and / or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
PAGE 3
Installation Instructions for the Following Wilson Amplifiers: Mobile Wireless Single Band Amplifier Model #801101 FCC ID: PWO824W V IC: 4726A-824W V The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Inside this Package Wireless amplifier DC plug-in power cable 6‘ extension cable How it Works Low-profile antenna (Option A - see p. 6) Universal connector (Option B - see p.
PAGE 4
Before Getting Started This guide will help you properly install Wilson’s single-band, mobile wireless amplifier. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment.
PAGE 5
Installing a Wilson Outside Antenna To receive the best cell signal, select a location in the center of the vehicle’s roof at least 12 inches away from any other antennas and free of obstructions. Follow the specific antenna installation instructions included with the outside antenna (sold separately).
PAGE 6
Installing a Wilson Amplifier ! Warning: Do not plug in the DC power supply until the outside and inside antenna cables are attached to the amplifier. Select a location to install the amplifier that is away from excessive heat, direct sunlight or moisture and that has proper ventilation. Recommended installation locations are: • Under the seat • In the trunk • Under the dash Run the cable from the outside antenna and attach it to the FME-Male connector labeled “outside antenna” on the amplifier.
PAGE 7
Option A (Wireless) Installing a Wilson Inside Antenna Low-profile Antenna Amplifier Install the low-profile inside antenna 8-12 inches from where the cell phone or cellular data card will be used. ! Warning: Do not install the low-profile antenna within four inches of metal. (Metal found inside the vehicle’s seat will not affect the antenna’s performance.) Place the inside antenna on the side of the driver’s seat for maximum performance.
PAGE 8
Option B (Attached) Installing a Wilson Universal Connector Amplifier 6’ Extension Cable Universal Connector The universal connector must be placed directly on the cell phone or cellular data card to work properly. Attach the universal connector to the cell phone or cellular data card with the VELCRO® included in the package. The universal connector and extension cable included in the package are long enough to reach the amplifier location. This allows for ease and convenience of use.
PAGE 9
Powering up a Wilson Amplifier Make sure both the outside and inside antenna cables are connected before powering up the amplifier. Connect the DC plug-in power supply cable to the amplifier marked “Power” and insert the large end into DC power socket (the cigarette lighter outlet.) Carefully insert the power cable. ! Warning: Use only the power supply cable provided in this package. The power supply must be 12 V DC. The amplifier may remain on all the time.
PAGE 10
Warnings and Recommendations Warning: In a wireless installation, do not plug the amplifier directly into the cell phone or cellular data card using an antenna adapter. It will damage the cell phone or cellular data card. Warning: Do not install the inside antenna within four inches of metal. (Metal found inside the vehicle’s seat will not affect antenna performance.) Warning: Do not use any type of glass-mount antenna with this amplifier.
PAGE 11
Understanding the Amplifier Lights Power Indicator Light (located on the side) Signal Indicator Light (located on the back) Power Indicator Light Shows green when the unit is turned on. Signal Indicator Light A green light indicates normal operation. An orange light indicates overload from the cell site. The amplifier has temporarily shut down and will automatically reset. A red light indicates that oscillation has been detected. The inside and outside antennas are too close to one another.
PAGE 12
Amplifier Specifications Single Band 800 MHz Specifications 801101 FME-Male 50 ohms 5.5 x 4.3 x 1.4 inch or 14 x 10.8 x 3.5 cm 1.32 lbs or 0.