TM Cellular Signal Booster 460001/460101 Need help? www.WilsonElectronics.com Tech Support 866-294-1660 Mon.- Fri.
! IT IS VERY IMPORTANT TO POWER YOUR SIGNAL BOOSTER USING A SURGE PROTECTED AC POWER STRIP WITH AT LEAST A 1000 JOULE RATING. FAILURE TO DO THIS WILL VOID YOUR WARRANTY IN THE EVENT OF A POWER SURGE OR LIGHTNING STRIKE. ! THE SIGNAL BOOSTER UNIT IS DESIGNED FOR USE IN AN INDOOR, TEMPERATURECONTROLLED ENVIRONMENT (LESS THAN 150 DEGREES FAHRENHEIT). IT IS NOT INTENDED FOR USE IN ATTICS OR SIMILAR LOCATIONS SUBJECT TO TEMPERATURES IN EXCESS OF 150°F.
Package Contents DT4G Desktop Antenna (5’ RG-174 comes attached) 30’ RG6 Coax Cable (950630) Outside Panel Antenna Kit Outside Panel Antenna 30’ RG6 coax cables (301213) (314473-0630) AC Power Supply 5V / 2.5A (Not included with some models) (859948) Cable Connector (971129) Appearance of device and accessories may vary.
Find the Strongest Cellular Signal Before you install your DT4G signal booster, you must determine the location of the best available cellular signal. This will affect the location of your Outside Antenna and will help you get the best performance from your DT4G. You can find the strongest signal outside your building, typically at the highest point available, using any of the following methods: 1. Best method: Connect the Outside Antenna to the DT4G signal booster, and the DT4G to the Desktop Antenna.
Quick Install - Inside Window Mount Option 4. Insert the Outside Antenna into the cradle. Additional installation options on pg. 6-8 Find the Strongest Cellular Signal (See page 4 for suggested methods.) Ready to Install Inside Window Mount 1. Select a location on the inside of a window as high as possible and at least 20 feet from where the DT4G will be located.
8. Connect the DT4G to a surge protected AC power strip with at least a 1000 Joule rating. If your DT4G is working correctly, the lights will be green. Installation Options utside Pole Mount Option O (Best Option) 1. Select a location on the roof where the Outside Antenna can be mounted on a pole maintaining at least 20 feet of vertical or horizontal separation from the inside Desktop Antenna. If the lights are orange or red, see the “Troubleshooting” section on page 10.
4. Fit the assembly onto the pole in your desired location by sliding the second half of the bracket onto the U-bolt and securing it with the lock washers and nuts provided. Be sure the cradle is at the desired height and rotated toward the strongest cellular signal before Rotate in 45° tightening the nuts. Do not over tighten. increments 3. Drill four holes where you marked, using a 3/16-inch bit. Insert the plastic screw anchors provided in Packet B. 5.
Rafter Mount Option Additional Considerations 1. Select a location in the building’s rafters where the Outside Antenna can be mounted directly above the Desktop Antenna with at least 20 feet vertical or horizontal separation. The location should allow you to mount the Outside Antenna roughly in the direction of the strongest cellular signal.
3. Keep the DT4G and the Desktop Antenna at least 18 inches away from each other with the Wilson logo on the Desktop Antenna facing away from the DT4G. Minimum separation of 18 inches 4. Do not face the Outside Antenna and the Desktop Antenna toward each other. This can cause the DT4G to show red lights and shut down, preventing oscillation or feedback (see troubleshooting on pg. 13).
5. Ensure the Inside Antenna is facing away from both the DT4G and the Outside Antenna. Note Face Inside Antenna away from DT and Outside Antenna Troubleshooting & Understanding Lights The DT4G includes four indicator lights, one for each band (for more information about the frequency bands used by your cell service provider visit wirelessadvisor.com.) All indicator lights will be green, orange or red. Green indicates the unit is powered and working properly. You always want the lights to be green. 6.
IMPORTANT NOTE: Reducing the gain decreases the inside coverage area. If the amount of coverage area is sufficient when the green light comes on, your installation is complete. coverage, turn the Outside Antenna away from the strongest cellular signal in small increments until the light turns green. c) You need to increase the distance between the Outside Antenna and the Desktop Antenna by moving them horizontally and/or vertically farther apart making sure they are not facing towards each other.
Additional FAQ: What hours can I contact tech support? Technical Support can be reached from 7:00am to 6:00pm MST, by calling (866-294-1660), or by email, at tech@wilsonelectronics.com How does weather affect the performance of my Outside Antenna? Water vapor (e.g. rain, fog, snow or other precipitation) creates an effective filter to cellular signal. In times of heavy precipitation, you may see less performance.
Safety Guidelines WARNING: T o uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas and 4 feet of separation distance from Desktop antennas. WARNING: C onnecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. WARNING: U se only the power supply provided in this package. Use of a non-Wilson Electronics product may damage your equipment.
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _________
Signal Booster Specifications DT4G Specifications Model Number 460001 SMA-male on the Inside Antenna / F-male on the Outside Antenna Antenna connectors Antenna impedance 50 Ohms Dimensions 4.5 x 6.44 x 1.19 in. or 11.43 x 16.35 x 3.02 cm Weight 0.4 lbs or 0.18 kg Frequency Frequency 704-746 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Power output for a single phone (uplink) dBm Maximum Power 700 MHz Band 17 700 MHz Band 13 800 MHz 1900 MHz 1700 MHz 23.7 23.6 24.
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 2-Year Warranty Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials.