User's Manual

ManualsBrandsWilson Electronics ManualsElectronics900MHZ IDEN & 1900MHZ PCS BOOSTER AMPLIFIER

Amplifier

Installation

Guide

Warning: This manual contains

important safety and operating information.

Please read and follow the instructions

in this manual. Failure to do so could be

hazardous and result in damage to your

amplier.

SIGNALBOOST™

900/1900 MHz

iDEN

Amplier

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1

How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2

Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3

Installation Overview · · · · · · · · · · · · · · · · · · · · · · · · · · · 3

Installing the Antenna (Vehicle) · · · · · · · · · · · · · · · · · · · 4

Installing the SIGNALBOOST™ Amplier (Vehicle) · · · 5

Installing the Antenna (Home/Ofce) · · · · · · · · · · · · · · · 7

Installing the SIGNALBOOST™ Amplier (Home/Ofce) 7

Installing the Universal Connector (Cellular Data Card) 7

Powering Up the Amplier · · · · · · · · · · · · · · · · · · · · · · · 8

Warnings and Recommendations · · · · · · · · · · · · · · · · · 9

About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · · 10

Amplier Specications · · · · · · · · · · · · · · · · · · Back Cover

Wilson

Electronics, Inc.

Summary of content (12 pages)

PAGE 1
Amplifier Installation Guide SignalBoost™ 900/1900 MHz iDEN Amplifier Contents: Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1 How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3 Installation Overview · · · · · · · · · · · · · · · · · · · · · · · · · · · 3 Installing the Antenna (Vehicle) · · · · · · · · · · · · · · · · · · · 4 Installing the SIGNALBOOST™ Amplifier (Vehicle
PAGE 2
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson’s 30-day money-back guarantee. If, for any reason, the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 1-Year Warranty Wilson Electronics amplifiers are warranted for one (1) year against defects in workmanship and / or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
PAGE 3
Installation Instructions for the Following Wilson Amplifier: SignalBoost™ 900/1900 MHz iDEN Amplifier Model #2B4310, Part #814310 FCC ID: PWO2B4310SM IC: 4726A-2B4310SM Patent Pending The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.
PAGE 4
Before Getting Started This guide will help you properly install Wilson’s dual-band, SignalBoost™ amplifier. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. If you do not understand the instructions in full, please contact Wilson Technical Support at 866-294-1660.
PAGE 5
Vehicle Installation Installing the Antenna To receive the best cell signal, select a location in the center of the vehicle’s roof at least 12 inches away from any other antennas and free of obstructions. The antenna must be installed vertically. Signal performance will be degraded if the antenna is not vertical. The antenna cable may be run through the door to the amplifier. ! Warning: The mobile antenna used with this amplifier must have a separation distance of at least 8 inches from all persons.
PAGE 6
Vehicle Installation Installing the Wilson SignalBoost™ Amplifier ! Warning: Do not plug in the DC power supply until the antenna and other cables are attached to the amplifier. Select a location to install the amplifier that is away from excessive heat, direct sunlight or moisture and that has proper ventilation. Recommended installation locations are: • Under the seat • Under the dash Run the cable from the antenna and attach it to the FME-Male connector labeled “outside antenna” on the amplifier.
PAGE 7
Option 2 - Adhesive Bracket Clean the area where the bracket is to be mounted with rubbing alcohol and a soft cloth. Allow to dry. Peel the backing to expose the adhesive and press the bracket onto the desired location in the vehicle. Note: be sure the bracket is positioned vertically, not horizontally. Allow the adhesive to cure for 24 hours before you attach the cradle.
PAGE 8
Home/Office Installation Installing the Antenna To receive the best cell signal, select a window location at least 12 inches away from any radio or television antennas and free of obstructions. Using the suction cups, position the optional mounting bracket on the window at a height convenient to where the amplifier will be located, then attach the antenna to the bracket. The antenna must be installed vertically. Signal performance will be degraded if the antenna is not vertical.
PAGE 9
The universal connector must be placed directly on the cellular data card to work properly. Attach the universal connector to the cellular data card with the VELCRO® included in the package. IMPORTANT: The adhesive of the gray Velcro patch needs time to “cure.” For best results, do not use the Velcro connection for a minimum of 24 hours after application. Cellular data card The universal connector and extension cable included in the package are long enough to reach the amplifier location.
PAGE 10
Warnings and Recommendations Warning: Do not plug the amplifier directly into the cell phone or cellular data card using an antenna adapter. It will damage the cell phone or cellular data card. Warning: Do not plug in the power supply until the antenna other cables are attached to the amplifier. Warning: RF Safety: Vehicle and indoor building antennas must be installed with a separation of at least 8 inches from all persons.
PAGE 11
About Wilson Electronics Wilson Electronics, Inc. has been a leader in the wireless communications industry for nearly 40 years. The company designs and manufactures amplifiers, antennas and related components that significantly improve cellular telephone signal reception and transmission in a wide variety of applications, both mobile and in-building.
PAGE 12
Amplifier Specifications Dual Band 900/1900 MHz Specifications 2B4310 FME-Male 50 Ohms 5 x 3.5 x 1.2 inch or 12.7 x 8.9 x 3 cm 1.03 lbs or 0.