In-Line 17dB Adjustable Gain 800/1900 MHz Smart Technology ™ Signal Booster Contents: Quick Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Understanding the Signal Booster Lights . . . . . . . . . . . . . . . Warnings and Recommendations. . . . . . . . . . . . . . . . . . . . .
Installation Instructions for the Following Wilson Signal Booster: In-Line, 17dB Adjustable Gain 800/1900 MHz Smart Technology ™ Signal Booster Model # 276215 FCC ID: PWO276215 IC: 4726A-276215 The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. How it Works Wilson Electronics Signal Boosters are bi-directional devices that deliver service levels consistent with what would be expected in areas of high cell network coverage.
Quick Install Overview See Installation Diagram on page 3. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660. 1. Install In-Building Signal Booster (such as the AG Pro 75 sold separately). Use the installation guide for the model you purchased to install. 2. Select a location to install the In-Line Signal Booster that is away from excessive heat, direct sunlight, moisture and has proper ventilation. Do not place the Signal Booster in an air-tight enclosure. 3.
Installation Diagram Note: Do not install the In-Line without an In-Building Signal Booster between the Outside Antenna and In-Line. Outside Antenna Note: Install the In-Line close as possible to Inside Antenna for optimal performance. Inside Antenna Preferred Method: Place the Inside Antenna in the ceiling facing down for the best coverage. Note: The Inside Antenna may be mounted on the wall directly under the Outside Antenna, in the null zone, if 20 feet of vertical separation can be maintained.
Before Getting Started This guide will help you properly install your Wilson Electronics Signal Booster. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. Contact Wilson Electronics Technical Support with any questions at: 866-294-1660.
Reasons for Using a In-Line Signal Booster with In-Building Installations Covering multiple rooms or even floors of a building can be challenging as each is a different size and shape. Balancing the signal coverage can require multiple attenuators, cables, taps and splitters. All of these can decrease your system gain and coverage. Reasons to install an In-Line Signal Booster include: 1.
Installing a Wilson Electronics In-Line Signal Booster Select a location to install the In-Line Signal Booster that is away from excessive heat, direct sunlight, moisture and has proper ventilation. Do not place the Signal Booster in an air-tight enclosure.
Powering up a Wilson Electronics In-Line Signal Booster 1. Never point the front of a Directional Outside Antenna toward the Inside Antenna. See Figures 1 & 2 on page 8. 2. Run the antenna cable from the In-Building “Inside Antenna” connector to the In-Line Signal Booster “Outside Antenna” connector and attach to both connectors. Run the Inside Antenna cable to the In-Line Signal Booster and attach it to the connector labeled “Inside Antenna” on the In-Line Signal Booster.
Figure 1 CORRECT INSTALLATION Point antennas away from each other Outdoor Antenna Inside Panel In-Line Antenna (806215) Signal Booster Figure 2 INCORRECT INSTALLATION We do not recommend 806215 right on Outside Antenna Outdoor Antenna Not recommended placement for Inside Panel In-Line (806215) Antenna Signal Booster Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Mon.- Fri. Hours: 7 am to 6 pm MST.
Understanding the Signal Booster Lights and Troubleshooting During installation mode the Signal Booster is resetting itself very quickly to aid the installer. The Signal Booster is equipped with two indicator lights, one for the 800 MHz band and the other for the 1900 MHz band. For the first 15 minutes that the Signal Booster is plugged in, it is programed for a test and alignment period.
2. Solid Red If either of the two lights on the Signal Booster are solid red, this indicates that the Signal Booster has shut down on that frequency to prevent an oscillation (feedback). First, make sure that all the connections are tight. Then reduce the gain of the Signal Booster in small increments by rotating the gain control, counter clockwise, waiting 5 seconds between each adjustment for the Signal Booster to reset. Continue this adjustment until the light turns blinking or solid green.
Warnings and Recommendations Warning: The Directional Antenna must always be located so the back or side points to the Inside Antenna. Never point the front of the Outside Antenna toward the Inside Antenna – this is to prevent oscillation. Warning: Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. Warning: Use only the power supply provided. Use of a non-Wilson Electronics product may damage your equipment.
About Wilson Electronics Wilson Electronics, Inc. has been a leader in the wireless communications industry for over 40 years. The company designs and manufactures Signal Boosters, antennas and related components that significantly improve cellular phone signal reception and transmission in a wide variety of applications, both mobile (vehicle, RV, marine) and in-building (home, office, M2M).
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 1-Year Warranty Wilson Electronics Signal Boosters are warranted for one (1) year against defects in workmanship and/or materials.
This device complies with Part 15 of FCC rules. The transaction is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this equipment. Copyright © 2012 Wilson Electronics, Inc. All rights reserved. One or more of the following U.S.
In-Line 17 dB Specifications Model Number 276215 Antenna connectors N-Female Antenna impedance 50 ohms Dimensions 5.7 x 4.2 x 1.5 inch (14.0 x 10.8 x 3.9 cm) Weight 1.27 lbs (0.
