User's Manual

ManualsBrandsWilson Electronics ManualsElectronicsSINGLE-BAND ADJUSTABLE GAIN SIGNAL

Wilson

Electronics, Inc.

Contents:

Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . . . 1

Quick Install Overview ................................2

Installation Diagram ..................................3

Before Getting Started ................................4

Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Finding the Strongest Signal ...........................6

Installing the Inside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing a Wilson Electronics Signal Booster. . . . . . . . . . . . . . 9

Powering up a Wilson Electronics Signal Booster ...........9

Understanding the Signal Booster Lights . . . . . . . . . . . . . . . . 10

Warnings and Recommendations ......................12

Guarantee & Warranty ...............................14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: This manual contains important safety and operating information. Please read and

follow the instructions in this manual. Failure to do so could be hazardous and result in

damage to your Signal Booster.

4G-A LTE 700

Operates on 700 MHz Band 12/17

(Band 12/17 is AT&T

LTE)

70 dB Adjustable Gain

In-Building Wireless 700 MHz

Smart Technology

™

Appearance of device and accessories may vary.

Summary of content (16 pages)

PAGE 1
4G-A LTE 700 Operates on 700 MHz Band 12/17 (Band 12/17 is AT&T® LTE) 70 dB Adjustable Gain In-Building Wireless 700 MHz Smart Technology ™ Contents: Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
Installation Instructions for the Following Wilson Electronics Signal Boosters: 4G-A LTE 700 Operates on 700 MHz Band 12/17 (Band 12/17 is AT&T LTE), 70 dB Adjustable Gain In-Building Wireless Smart Technology ™ Signal Booster Model # 272570 FCC ID: PWO272570 ® How it Works Wilson Electronics Signal Boosters are bi-directional devices that deliver service levels consistent with what would be expected in areas of high cell network coverage.
PAGE 3
Quick Install Overview See Installation Diagram on page 3. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660. 1. Select a location to install the Signal Booster that is away from excessive heat, direct sunlight, moisture and has proper ventilation. Do not place the Signal Booster in an air-tight enclosure. 2. Select a location on the roof of the building to install the Outside Antenna.
PAGE 4
Installation Diagram Outside Antenna Inside Antenna Preferred Method: Place the Inside Antenna in the ceiling facing down for the best coverage. Note: The Inside Antenna may be mounted on the wall directly under the Outside Antenna, in the null zone, if 20 feet of vertical separation can be maintained. Null Zone: The area under the Outside Antenna, where the Outside Antenna radiates the least. Note: A Lightning Surge Protector is recommended for all building installations (sold separately).
PAGE 5
Before Getting Started This guide will help you properly install your Wilson Electronics Signal Booster. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. Contact Wilson Electronics Technical Support with any questions at: 866-294-1660.
PAGE 6
Reasons for Weak Cellular Signals Anyone who uses a cell phone or cellular data card knows the frustration of not being able to connect to or maintain a strong cellular signal. When this occurs, it is generally due to one of two reasons: 1.
PAGE 7
Warning: Lightning protection is recommended for all installations (sold separately #859902). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines. Installing Lightning Protection (sold separately) Install the Lightning Surge Protector (LSP) close to the Signal Booster.
PAGE 8
the phone in the test mode so the actual signal strength can be read, as bars are not the most accurate. Go to www.WilsonElectronics.com for help in finding the test mode for your phone. Always make sure the person inside the building gives the signal time to arrive and register on the phone (between 10-30 seconds for phone to reset to the signal reading).
PAGE 9
After drilling the required hole, run the cable through and seal it with cable bushings, silicone or other waterproof sealant to enclose the hole that you have created. In some instances, it may be possible to run the cable up into the fascia of the attic overhang. In this circumstance, the cable will be accessible in the attic for further routing.
PAGE 10
Installing a Wilson Electronics Signal Booster Select a location to install the Signal Booster that is away from excessive heat, direct sunlight, moisture and that has proper ventilation. Do not place the Signal Booster in an air-tight enclosure. Recommended installation locations for in-building Signal Boosters are near a power outlet and in a closet or on a shelf. Note: It is important to have adequate air ventilation. Maintain at least 6 inches of clearance from surrounding objects.
PAGE 11
CORRECT INSTALLATION Point antennas away from each other Inside Panel Antenna Signal Booster Figure 1 Outdoor Antenna INCORRECT INSTALLATION Never point antennas toward each other Inside Panel Antenna Outdoor Antenna Signal Booster Figure 2 Understanding the Signal Booster Lights and Troubleshooting During installation mode the Signal Booster is resetting itself very quickly to aid the installer. The Signal Booster is equipped with one indicator light for the 700 MHz band.
PAGE 12
towers. If the light is blinking orange, this indicates that gain should be reduced due to close proximity to a cell tower. First, turn down the gain control until you get a blinking green light. The Signal Booster is now working with reduced gain. If the gain is not adequate for good coverage, you will need to turn the gain to maximum and then rotate the Outside Antenna until the light turns to blinking green, waiting 5 seconds between each adjustment for the Signal Booster to reset.
PAGE 13
*Note: If the antennas cannot be sufficiently separated, the booster will have to operate with reduced performance by decreasing the gain until a green light is obtained. 4. SOLID Green The 700 MHz indicator light on the Signal Booster will be a solid green after the first 15 minute installation period, if the unit is powered up and working properly. Warnings and Recommendations Warning: The Directional Antenna must always be located so the back or side points to the Inside Antenna.
PAGE 14
About Wilson Electronics Wilson Electronics, Inc. has been a leader in the wireless communications industry for over 40 years. The company designs and manufactures Signal Boosters, Antennas and related components that significantly improve cellular phone signal reception and transmission in a wide variety of applications, both mobile (marine, RV, vehicles) and in-building (home, office, M2M).
PAGE 15
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day moneyback guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 1-Year Warranty Wilson Electronics Signal Boosters are warranted for one (1) year against defects in workmanship and/or materials.
PAGE 16
4G-A LTE 700 Specifications 4G-A LTE 700 Specifications Model Number 272570 Antenna connectors N-Female Antenna impedance 50 ohms Dimensions 5.7 x 4.2 x 1.5 inch (14.0 x 10.8 x 3.9 cm) Weight 1.27 lbs (0.