User's Manual

ManualsBrandsWillis Electric ManualsElectronicsOutdoor Smart Plug

Table Of Contents

ZW97 Z-Wave 2-Channel OutDoor Smart Plug

Introduction:

Thank you for choosing the ZW97 Z-Wave control product.ZW97 enabled product allows users to remotely

control lighting, home appliance, and make home control easy with low installation and maintenance costs.

You may begin with a few Z-Wave enabled devices as well as some of our products to build up acomplete

home automation system.

The ZW97 is a Z-Wave enabled device and is fully compatible with any Z-Wave Plus enabled network.Each

module is designed to act as a repeater,which will re-transmit a radio frequency (RF),signal by routing the

signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination.

Basic Operation:

The ZW97 can control two channel outlet outputs separately

Press the button one times controller all outlet ON/OFF

Press the button two times controller left outlet ON/OFF

Press the button three times controller right outlet ON/OFF

Follow this 2-step procedure to add your new ShowHome device to your Z-Wave network:

1 Put your Z-Wave controller into inclusion mode. Consult your controller manual if you’re unsure how to do this.

2 Press the button five times. This will take a few moments to complete.

MANUAL RESET

- To be used only in the event that the network primary controller is lost or otherwise inoperable.)

MANUAL RESET

- To be used only in the event that the network primary controller is lost or otherwise inoperable.)

1）power off

2 ) hold on 5 seconds when turn on the power of ZW97

-----B: ON/OFF/PROG Push button

-----C: Z-Wave controlled left outlet

-----D: Z-Wave controlled right outlet

-----Node: There are LED instructions below the button

White LED indicates ON/OFF

RED LED indicates temperature alarm

Include ZW97 to/from a Z-Wave Gateway with supporting Security the ZW97 can support the Primary Controller that implemented the security S2.

Refer to your primary controller instructions to process the Secure Inclusion.The Below listed Command Class are all supported the Security S2

COMMAND_CLASS_ZWAVEPLUS_INFO,

COMMAND_CLASS_VERSION,

COMMAND_CLASS_MANUFACTURER_SPECIFIC,

COMMAND_CLASS_DEVICE_RESET_LOCALLY,

COMMAND_CLASS_ASSOCIATION,

COMMAND_CLASS_ASSOCIATION_GRP_INFO,

COMMAND_CLASS_POWERLEVEL,

COMMAND_CLASS_SWITCH_BINARY,

COMMAND_CLASS_SWITCH_ALL,

COMMAND_CLASS_CONFIGURATION,

COMMAND_CLASS_NOTIFICATION_V8,

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2,

COMMAND_CLASS_TRANSPORT_SERVICE_V2,

COMMAND_CLASS_SECURITY,

COMMAND_CLASS_SECURITY_2,

COMMAND_CLASS_SUPERVISION

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Summary of content (3 pages)

PAGE 1
ZW97 Z-Wave 2-Channel OutDoor Smart Plug Introduction: Thank you for choosing the ZW97 Z-Wave control product.ZW97 enabled product allows users to remotely control lighting, home appliance, and make home control easy with low installation and maintenance costs. You may begin with a few Z-Wave enabled devices as well as some of our products to build up acomplete home automation system. The ZW97 is a Z-Wave enabled device and is fully compatible with any Z-Wave Plus enabled network.
PAGE 2
Support for Association Groups ZW97 supports 3 association groups. A maximum of 5 node ID. -Association group_1: Association group_1 is default to associate with the primary controller (Gateway/Hub/Controller) for ZW97 Status change report, refer to below for report details: 1. ZW97 will trigger AUTO report function if the Output status had been changed. 2.
PAGE 3
FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.