DLT-100 User Guide 1
What’s included with DLT-100 ① DLT-100 ② USB Cable ③ Adaptor ④ Plug 1 (Europe) ⑤ Plug 2 (England) ⑥ Plug 3 (Australia) ① ③ ② ④ ⑤ ⑥ 2
Location of Controls ⑤ External Mic. Jack(3.5mm) ⑥ External Headphone Jack(3.
Simultaneous Interpretation Mode 4
Simultaneous Interpretation Mode 1. Setting procedure for Interpretation Mode 1 Press and hold power button for 2 seconds to turn DLT100 on 2 Press No and Yes button together for 2 second Mode icon will blink on LCD 3 Press ( +) or (– )button to select mode Note In Interpretation Mode 3 different mode can be used as shown in left side. Each has different role but they all can be used un Interpretation system Press (-) button, the mode will be changed in above sequence.
Simultaneous Interpretation Mode 1. Setting procedure for Interpretation Mode 4 5 Press mode button to select interpretation mode 6 Press ( +) or (– )button to select SLV or MAS SLV- Slave MAS-Master When mode selection is made then SLV icon will blink 8 7 1 Press mode button to select SLV or MAS Note When channel number is at No.
Simultaneous Interpretation System 1.
Simultaneous Interpretation System 1.Setting procedure for Interpretation System Final setting for Master unit 11 13 Press mode button to select group number 15 14 Press mode button to complete Hour setting Press ( +) or (– )button to adjust Hour When group number selection is made then number of hour will blink Press ( +) or (– )button to adjust minute 16 Press No and Yes button together for 2 second to complete setting Note: 1.Master and Slave unit must have same group number 2.
Simultaneous Interpretation Mode Interpreter -3 units Receiver – 20 units CASE1) Select Channel and Listen English Ch1 Chinese Ch2 Korean Ch3 CASE2) Main Speaker -1 units Interpreter – 2 units Receiver – 20 units Select Channel and Listen Main Speaker is set to “0” Channel Interpreter -A Ch1 CASE3) Interpreter –B Ch2 Interpreter-1 units AP(Relay) – 1 units Receiver – 20 units Interpreter -A Ch1 AP (=Repeater) Extend the distance 9
Two-way tour guide mode (conference mode) 2. Setting procedure for Two-way tour guide mode(conference mode) Æ Mode change from interpretation to Two-way tour guide mode 1 Press and hold power button for 2 seconds to turn DLT100 on 2 Press No and Yes button together for 2 second Mode icon will blink on LCD 4 3 Select tour guide system Press ( +) or (– )button to select mode 4 Press (-) button, the mode will be changed in above sequence. Press (+) button, reverse sequence.
Two-way tour guide mode (conference mode) 2.
Two-way tour guide mode (conference mode) 2.
Two-way tour guide mode (conference mode) 2. Setting procedure for Two-way tour guide mode(conference mode) Note If you don’t want to set speech time, please set speech time to “0” 18 Press No and Yes button together for 2 second to complete setting Note: 1.Master and Slave unit must have same group number 2.
Two-way tour guide mode (conference mode) Tour guide phone-2 units Receiver – 20 units CASE1) Just Listen English Chinese CASE2) Tour guide phone-3 units Receiver – 20 units Two way communication Two people can talk at the same time Just Listen 14
Troubleshooting Problems Cause What to do Power does not turn-on Discharge of battery Charge the battery Power turned off automatically Master device can’t be found Set Master device Power doesn’t turn off Program Error Press reset button on the backside of device Disconnection of earphone Check Earphone Connection Master doesn’t exist Set Master Different Group Number settings Setting every unit in same group number Out of range Enter the range of 30~50m from the master unit More than 1
FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to The following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. FCC Part 15.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC RC exposure compliance requirement, please avoid direct contact to the transmitting antenna during transmitting. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.