Quick Start Guide LTE USB DONGLE WHT-25LT Whoop 1
Thank you for choosing the LTE USB Dongle. This device provides high speed data connection to the wireless network. Note: • This guide briefly describes the appearance of the device and the steps for using it. • For details about how to set the device and management parameters, see help information at www.whoopmobility.com • WHOOP reserves the right to modify or enhance all products described in this document, and to revise this documentation without prior notice. • Visit www.WHOOPMOBILITY.
Getting to Know Your device The following figure shows the device sketch. The actual product may look different.
1. USB connector Connect the device to a computer or other data ready device. Note: Please consult your supplier for the appropriate model.
The IMEI and Serial number are printed on the device as shown in the following figure.
2. LED Blue and green lights flash alternately: Blue(1800ms)-green(200ms)-green(200ms)-Blue(200ms) No SIM card No Network connection No Data connection Idle Steady cyan.Blue flashes once every 1800ms : Data transfer is ongoing Light off: device is off. 3. Reboot Use a small pin to push the reset button. 4. SIM card slot Subscriber Identity Module (SIM) card holder for the device.
Install SIM card 1. Remove the front cover as shown in the figure below.
2. Insert SIM card as shown in the following figure. Ensure that the SIM is place in the right direction and fully embedded.
3. Replace the front cover on the device properly as shown in the figure below.
Note: • Ensure that the beveled edge of the SIM card is properly aligned with that of the SIM card slot. • Do not remove the SIM card when the device is in use. Otherwise the device may be damaged and the data in the SIM may get corrupt. • Use compatible SIM cards to avoid damage to your device and SIM card. • Make sure the SIM card is Unlocked. • Make sure the SIM is Activated and has a DATA plan.
Connection Scenarios Use the device for Internet access at your computer or laptop. There are 2 network connection modes what can be selected with the DIP switch at the device. Right ➡ ：🌐 LAN NETWORK MODE ：In this mode you can install the Windows drivers. The device will show up as a LAN connection. Left ⬅ ：📶 MOBILE NETWORK MODE ：(first install the driver in LAN network mode). In this mode the device will show up as a MOBILE connection.
Plug the device into a free USB port at your computer.
Connection scenario 1 Using Your device with a computer as a LAN network connection. The procedure for installing the device drivers may vary depending on your computer's operating system. The following instructions are specific to Windows OS. Connecting to a Network 1. Connect the device to one of your computer's USB ports. 2. When the device is connected the first time, you need to install the drivers. 3. In the “Drivers” folder at the device USB disk, select “Setup.exe” 4.
Note: • Make sure the Network mode DIP switch is in the Right (LAN) position. • The default user name and password of the device management web page are both “admin”. • If you are not connected to a mobile network, visit http://192.168.100.1 to check the device status. • If you cannot access http://192.168.100.1, disconnect other network connections, such as an Ethernet or Wi-Fi connection, remove and then reinsert the device, and/or restart the computer.
Note: • Make sure the Network mode DIP switch is in the LEFT (MOBILE) position. • In Mobile mode the device COM ports will be available. • In this mode the network connection is managed by Windows. Please use the Windows network settings page to make changes to your connection or APN settings. Disconnecting from a Network Before you remove the device, make sure that the data connection has been disconnected. Disconnect the device's data connection through the network connections of Windows.
Note: 1. Restoring factory settings will delete all the user-defined settings and restores all the settings to its original factory settings 2. Right ➡ ：🌐 LAN NETWORK MODE ：In this mode you can install the Windows drivers. The device will show up as a LAN connection. 3. Left ⬅ ：📶 MOBILE NETWORK MODE ：(first install the driver in LAN network mode). In this mode the device will show up as a MOBILE Connection. 1.RESET 2.
Factory settings Model: WHT-25LT Web: http://192.168.100.1 Password: admin Restoring Factory Settings If you wish to restore factory settings on your device, you can connect the device to a computer or a power outlet, then press and hold the RESET button for 5 seconds. Visit www.whoopmobility.com for additional information and support. Email: service@whoopinternational.
Dimensions 95 x 36 x 13（mm） Processor Qualcomm Power Consumption 2W (Max) Antenna 1×4G Main antenna,1×4G Auxiliary antenna Sim card slot NANO SIM card slot Operating Voltage 5V USB Whoop 18
Temperature Range Operating: -20°C to 60°C Storage: -40°C to 85°C Humidity Operating: 5％ to 95％(non-condensing) Storage: Max. 90％ (non-condensing) Host Interface USB 2.
Limited Warranty WHOOP provides a one year warranty service after purchase of this product. Within this year when the product stops working because of design defects, the product will be repaired or replaced. (replacement of the product is sole to the decision of Whoop and only when the product is not physically damaged).
Notice of content and ownership Copyright © 2020 WHOOP. All rights reserved. The full and total contents of this documentation is protected by copyright laws. Any form of reproduction, transference, distribution or saving of the contents of this document, be it partly or wholly, without prior consent in writing from WHOOP, is prohibited. WHOOP and the "WHOOP" logo are registered trademarks of WHOOP USA INC. and are protected by all applicable laws.
This documentation was supplied to serve as a user guide exclusively for WHOOP devices and contains no clarification with regard to hardware- or software configurations of the products described within this document. The availability of specific products or expansions may vary depending on your location. For additional information, please refer to your nearest WHOOP dealer or at www.whoopmobility.
Before using this device, please thoroughly acquaint yourself with the user instructions and safety information regarding radiation and SAR. Please visit www.whoopmobility.com for more details. FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
for USB dongle, as described in this user guide, is 1.15 W/kg. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: 2AP7L-WHT25LT.
