WBU-1000 User Guide WIRELESS DIGITAL BACKUP CAMERA INSTALLS IN MINUTES
Because the WBU-1000 is truly wireless and does not tap into your vehicle's transmission or backup light, you must tell the unit when you are backing up. This also allows you to use your back up camera to view behind the vehicle at any time. When power is applied to the monitor an image will be present for 60 sec by default or the user selected time, if the screen goes blank and more time is required press the for an image to return to the monitor.
TABLE OF CONTENTS Components.................................................................................. 4 Getting Started..........................................................................5-6 Assembly / Installation............................................................7-8 Test the Camera............................................................................ 9 Attach to Vehicle........................................................................10 Mounting the Monitor.............
COMPONENTS 3 1 2 5 4 7 6 8 9 10 11 12 14 1. 2. 3. 4. 5. 6. 7. 8. Monitor Camera Solar cells (2) Suction cup mount Dash disk Tie wraps License back-plate Long screws (Domestic) (4) 16 13 15 9. 10. 11. 12. 13. 14. 15. 16. 17.
GETTING STARTED The WBU-1000 is equipped with a built-in rechargeable lithium battery and is connected with two solar panels that trickle charge the built-in lithium battery when sunlight is available. This will minimize or eliminate the need to manually charge the unit during the year. A USB charging port is provided to initially charge the battery prior to mounting on your vehicle as well as to recharge if needed.
GETTING STARTED STEP 1 Charge The Camera 1. Connect the supplied USB cord to the micro USB port of the camera assembly. 2. Plug the USB cable into any standard USB charger with an output rating of 500ma or higher. 3. Charge the camera for 4 to 5 hours. Under normal use, the camera maintains a charge with exposure to sunlight. A battery status indicator is provided on the monitor when the camera is in use.
ASSEMBLY / INSTALLATION STEP 2 1. Peel the backing from the adhesive disks and apply one spacer over each license plate mounting hole. Apply pressure to set the adhesive tape. Adhesive disks backing 2. Slide your license plate into the assembly. If two of the license plate mounting holes are not required for attachment to your vehicle, insert the short machine screws and tighten with the supplied machine nuts. 3. If needed, two cushions are provided to protect your vehicle.
ASSEMBLY / INSTALLATION A B A B NOTE: Domestic and Import license plate screws are included and should be compatible with the vast majority of vehicles. Should your vehicle require a special diameter or thread, please consult your dealer. PAIRING MONITOR TO CAMERA Your WBU-1000 should automatically pair with your monitor. If your monitor does not automatically pair with the camera after initial charge, the following steps are to be used. 1. Disconnect both solar cell connections 2. Power on monitor 3.
TEST THE CAMERA Test the Camera Prior to attaching the license plate to your vehicle, follow the steps below to ensure pairing between the backup camera and monitor. 1. With power applied to the monitor, the button backlight will illuminate to indicate the monitor is ON and in Standby mode. 2. The Blue LED will blink briefly to indicate that it is attempting to communicate with the camera. When connected to the camera, the blue LED will turn solid.
ATTACH TO VEHICLE STEP 3 Attach license plate to vehicle Once you have tested the camera system and ensured the pairing between the backup camera and monitor, you are ready to reattach the license plate to your vehicle. Be sure to use the appropriate mounting screws for your vehicle (included). The camera angle should be adjusted to provide an optimal view of objects behind the vehicle. Note: Do not exceed 45 degrees up/down from central position.
MOUNTING THE MONITOR Find a mounting surface inside the vehicle for the monitor where it can be easily seen, and does not obstruct your vision when driving. NOTE: To maximize the effectiveness of the suction mount, the mounting location surface temperature should be between 50° and 100°F. Avoid application below 50°F. NOTE: Before permanently mounting the monitor, test the reception of the camera signal in several selected locations within easy reach as one may have better reception than another.
SETUP Functions of the Touch Buttons (left to right) : Touch to enable or cancel the video on the monitor Touch for 3 seconds to turn on/off the backup assist lines. Touch to select a corresponding function. : Touch to move to or adjust a corresponding function. : Touch to enable/cancel the menu. : Touch to move to or adjust a corresponding function. : Touch briefly to turn on, touch and hold for 3 seconds to turn on/off. Adjusting Monitor Settings 1. Touch the button to bring up the options 2.
MONITOR SETTINGS User selectable camera time durations The WBU-1000 has three user selectable camera time durations. You may choose to set the monitor to stay on for 30, 60 or 90 seconds by following the below steps when the monitor is powered on: 1. 2. 3. 4. 5. 6. Touch the Touch the or to move the cursor over SETUP Touch the to select SETUP Touch the or to move the cursor over TIME-OUT Touch the to select TIME-OUT Touch the or to move the cursor over your preferred time duration 7.
MONITOR SETTINGS Menu Operations Enter the main Menu Interface and 4 options are available including IMAGE PARAMETERS, IMAGE ROTATION, SETUP and SOFTWARE INFORMATION. Press or to select corresponding option, and then touch the button to enter the option. In the example above the IMAGE PARAMETERS (Brightness, Contrast, Color) Setting Interface is shown.
MONITOR SETTINGS Brightness/Contrast/Color Settings Press or on the interface to adjust the brightness as shown above. Image Rotation Select IMAGE ROTATION, and then touch the button to rotate or mirror the image. (It is best to have a video image displayed when making this selection). If you rotate the image on the display an orange box with arrows will appear . Select Software Information Touch the button to display the software version information.
TROUBLESHOOTING If the monitor does not turn on when power is applied: • Check to make sure the power source is active (if your 12V power port is switched with the vehicle ignition, your monitor will only work when the vehicle is running or the key is in the ON position) • Check to make sure the fuse and power cord are in working order • With power applied to the monitor, touch the If the monitor does not display images within a few seconds of pressing the button: • The battery in the camera may be depleted
DISCLAIMER The Whistler Digital Wireless Backup Camera is intended to assist responsible drivers but it does not relieve a driver from full responsibility for the operation of the vehicle. It is the driver’s sole responsibility to avoid contact with any objects, animals, or persons.
SAFETY Safety If at any time the backup camera assembly becomes damaged, hot or begins to swell, discontinue use immediately. Quickly and safely remove the backup camera from the vehicle and disconnect the solar charging cables. Do NOT continue to handle, attempt to use, or ship the damaged backup camera assembly. Failure to follow these procedures can cause damage to personal property or cause serious injury. Damaged or swollen batteries in the backup camera assembly can be unstable and very hot.
CARE AND MAINTENANCE Cleaning Do not clean or wipe the Back-Up Camera with solvents or chemical materials. If necessary, remove dirt or stains using a soft cloth dampened with a mild detergent solution. Fuse Replacement 1. Turn the cap on the tip of the power plug counterclockwise (no tools needed). 2. Remove the cap, center pin and fuse. 3. Replace the fuse with a new 1-amp fuse. 4. Replace the center pin and cap. Turn the cap clockwise. Disposal The Back-Up Camera is designed to provide years of service.
FCC AND IC INFORMATION IMPORTANT: FCC (Federal Communications Commission) requirements state that changes or modifications not expressly approved by Whistler could void the user’s authority to operate the equipment. FCC Part 15.19 Warning Statement This device complies with part 15 of the FCC rules.
FCC AND IC INFORMATION RF warning statement: The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. FCC ID : HSXBU01M / HSXBU01C IC Warning: This device complies with Industry Canada licence-exempt RSS standard(s).
SPECIFICATIONS CAMERA Operational Current (when transmitting): <220mA Pixels: 640 x 480 View Angle: 110° Image Sensor: 1/4“ CMOS VGA Image Quality: Max 25 fps. Camera Assembly: IP65 TRANSMITTER Frequency: 2400 ~ 2485.5MHz RF transmission distance: >328 ft. (>100 m) Operation/storage temperature: 14° to 122°F (-10° to 50°C) MONITOR LCD display screen size: 4.3 in. Power cord fuse: 1A Operational Current: <250mA Standby Current: 50mA.
WARRANTY INFORMATION Consumer Warranty This Whistler product is warranted to the original purchaser for a period of one (1) year from the date of original purchase against all defects in materials and workmanship, when purchased from an authorized Whistler retailer. This limited warranty is void if the unit is abused, misused, modified, installed improperly, or if the housing and/or serial numbers have been removed.
WARRANTY INFORMATION Service Under Warranty During the warranty period, defective units will be repaired or replaced (with the same or a comparable model), at Whistler’s option, without charge to the purchaser when returned prepaid, with dated proof of purchase to the address below. Units returned without dated proof of purchase will be considered out of warranty and therefore are not covered by the described Limited Warranty. (Refer to Service Out-of-Warranty section.
WARRANTY INFORMATION IMPORTANT: Whistler will not assume responsibility for loss or damage incurred in shipping. Therefore, please ship your unit insured with return receipt requested. CODs will not be accepted! 2. Include with your unit the following information, clearly printed: • Your name and physical street address for shipping (no PO Boxes), a daytime telephone number, and an email address (if applicable). • A detailed description of the problem (e.g.,“device will not power ON”).
WARRANTY INFORMATION Service Out-Of-Warranty Units will be repaired at “out-of-warranty” service rates when: • The unit’s original warranty has expired. • A dated proof of purchase is not supplied. • The unit has been returned without its serial number. • The unit has been misused, abused, modified, installed improperly, or had its housing removed. The minimum out-of-warranty service fee for your Whistler product is $65.00.
WARRANTY INFORMATION IMPORTANT: When returning your unit for service, be certain to include a daytime telephone number and an email address (if applicable). Customer Service If you have questions concerning the operation of your Whistler product, or require service during or after the warranty period, please call Customer Service at Toll Free (800)531-0004 Tel (479)273-6012 Representatives are available to answer your questions Monday - Friday from 8:00 a.m. to 5:00 p.m. (CT) or visit the FAQs at www.
CORPORATE HEADQUARTERS 1716 SW Commerce Dr. Ste. 8 Bentonville, AR 72712 Toll Free (800) 531-0004 TEL (479) 273-6012 www.whistlergroup.com CUSTOMER RETURN CENTER 1412 South 1st St. Rogers, AR 72756 Email: support@whistlergroup.com P/N 09A18 © 2018 The Whistler Group, Inc.
