tirescout.
tirescout.qxp 3/12/2012 10:34 AM Page 2 INTRODUCTION If you have questions concerning the operation of this Whistler product please call: CuSTOmer SeRVICE 1-800-531-0004 Monday - Friday • 8:00 am - 5:00 pm CT USA or visit our website www.whistlergroup.com Please keep the receipt in a safe place. You may register your product online at www.whistlergroup.com. For warranty verification purposes, a copy of your dated store receipt must still accompany any unit sent in for warranty work.
tirescout.qxp 3/12/2012 10:34 AM Page 3 TABLE OF CONTENTS Product Features 3-4 Installation 5-7 • System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 • Button Callouts and Icons . . . . . . . . . . . . . . . . . . . . . . . 4 • Sensor Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Sensor Battery Installation . . . . . . . . . . . . . . . . . . . . . . • Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Monitor Installation . .
tirescout.
tirescout.qxp 3/12/2012 10:34 AM Page 5 BUTTON CALLOUTS & ICONS Whistler’s ergonomic and user-friendly design provides a new level of operating convenience. Special features include: 1. Backlit LCD Display – Shows tire and battery information. 2. Left Button – Dual function button. Press and hold to power on the monitor. Quick press selects a “Down” function while in a setting mode. 3. Middle Button/Alert Light – Button illuminates red during an alert condition. Quick press mutes the alert audio.
tirescout.qxp 3/12/2012 10:34 AM Page 6 INSTALLATION Sensor Location The factory has already set up the codes for the 4 sensors which are provided and matched with the monitor, and each sensor is marked with the corresponding tire position [LF, RF, LR, RR, SP (spare tire)]. Install each sensor in the correct tire position as per the diagram. Sensor Battery Installation 1. Unscrew the sensor cap. 2. Insert battery into sensor ensuring that the positive “+” is facing up. 3. Replace the sensor cap.
tirescout.qxp 3/12/2012 10:34 AM Page 7 INSTALLATION Monitor Installation 1. Secure the monitor inside the vehicle cabin without obstructing the driver's vision of the road. 2. Place the monitor on the dashboard using the Dash Pad or the double-sided tape. If using the double sided tape make sure that the area choosen is clean and dry. Clean with isopropyl alcohol, if necessary, to remove any waxes or polishes. 3. Plug the power adapter into the cigarette lighter; turn the monitor on to fully charge.
tirescout.qxp 3/12/2012 10:34 AM Page 8 INSTALLATION Power Cord Connection • Plug the small end of the power cord into the unit’s power jack. • Plug the large end into the vehicle’s cigarette lighter socket. Turning the Monitor ON or OFF Manually You can turn off the monitor when you park the vehicle for a long period. To turn on/off the monitor manually, press and hold the Left button until you hear a beep.
tirescout.qxp 3/12/2012 10:34 AM Page 9 OPERATION Factory Default/Settings Mode The Min and Max settings from the factory are set to the following limits: High Pressure: 44PSI (3.0 BAR) Low Pressure: 29PSI (2.0 BAR) High Temperature: 158 ° F (70° C) Follow the steps below to change the settings to match your vehicle’s requirements: 1. In standby mode, press and hold the Middle button and release it after the beep. 2. Press the Middle button repeatedly to scroll through the different parameters. 3.
tirescout.qxp 3/12/2012 10:34 AM Page 10 OPERATION Factory Default/Settings Mode - continued Note: To restore the factory default settings follow these steps: 1. Turn off the monitor 2. Press and hold the Left button to turn on the monitor then immediately press and hold the Middle button for 3 seconds. 3. Release the Middle button after the unit beeps together with the flashing red light.
tirescout.qxp 3/12/2012 10:34 AM Page 11 OPERATION Adjusting the Alerts - continued High Pressure ( ) Setting When high pressure data flash, press the Left or Right buttons to adjust. Low Pressure ( ) Setting When low pressure data flash, press the Left or Right buttons to adjust. High Temperature ( ) Setting When high temperature data flash, press the Left or Right buttons to adjust. NOTE: High and low pressure settings are adjustable separately for the front, rear and spare tires.
tirescout.qxp 3/12/2012 10:34 AM Page 12 OPERATION Alerts The sensors send pressure and temperature readings to the monitor every 5 minutes. If any reading is out of the pre-defined values, you will notice 3 things: 1. An audible alarm 2. The red light on the monitor will flash 3. The corresponding icons on the monitor will flash Press any button to switch the alarm off.
tirescout.qxp 3/12/2012 10:34 AM Page 13 OPERATION Alerts - continued High Temperature Alert Icons Flash Red Light Flashes Fast Leakage Alert Icons Flash Red Light Flashes Sensor Low Battery Alert Icons Flash Red Light Flashes When the sensor detects high temperature in a tire, it will send an alert to the monitor immediately. The related tire icon, high temperature data and high temperature icon will flash. The audible alarm will be on together with the flashing red light.
tirescout.qxp 3/12/2012 10:34 AM Page 14 OPERATION Monitor Display Information Pressure Display The monitor displays the pressure of 4 tires. If the system senses high pressure, low pressure, or a puncture, an alert will be given and the display will flash a warning icon indicating the affected tire and that tires information. Temperature Display: Pressing the Middle button once will display the temperature reading for 10 seconds.
tirescout.qxp 3/12/2012 10:34 AM Page 15 OPERATION Monitor Display Information - continued Charging the Monitor The lithium-ion battery inside the monitor, when fully charged, is capable of running for 28 hours. For example, if you drive 4 hours per day, the monitor can be used for one week without connecting the power cord. When the low battery icon appears, a recharge is required. You need to charge the battery immediately. It will take 2.5 hours to charge fully.
tirescout.qxp 3/12/2012 10:34 AM Page 16 OPERATION Replacing the Transmitter Battery - continued 4. Replace a new CR1632 battery cell, ensure the positive “+” is facing upwards. 5. Check that the water-proof rubber seal is in its proper position. Screw the sensor cap back on. NOTE: If the water-proof seal is missing or damaged replace with a new seal that was provided with the unit. Failure to install this seal will damage the transmitter.
tirescout.qxp 3/12/2012 10:34 AM Page 17 TROUBLESHOOTING/ FCC INFO Problem: Monitor will not power on. • Press and hold the Left Button until the unit beeps. • May need to be charged. Plug in the power cord to power the monitor and charge it. • Make sure that lighter socket is functional. Problem: No Pressure display from a sensor. • Vehicle must be moving for sensors to transmit. • After vehicle has moved it may take up to 5 minutes for the sensor to transmit the tire information.
tirescout.qxp 3/12/2012 10:34 AM Page 18 WARRANTY INFORMATION Consumer Warranty This Whistler product is warranted to the original purchaser for a period of one year from the date of original purchase against all defects in materials and workmanship. This limited warranty is void if the unit is abused, modified, installed improperly, or if the housing and/or serial numbers have been removed. There are no express warranties covering this product other than those set forth in this warranty.
tirescout.qxp 3/12/2012 10:34 AM Page 19 WARRANTY INFORMATION 2. Include with your unit the following information, clearly printed: • Your name and street address (for shipping via UPS), a daytime telephone number and an email address, if applicable. • A detailed description of the problem (e.g.,“Monitor does not power on”). • A copy of your dated store receipt or bill of sale. 3. Be certain your unit is returned with its serial number.
tirescout.qxp 3/12/2012 10:34 AM Page 20 WARRANTY INFORMATION/SPECs Important: When returning your unit for service, be certain to include a daytime telephone number and an email address (if applicable). Customer Service If you have questions concerning the operation of your Whistler product, or require service during or after the warranty period, please call Customer Service at: 1-800-531-0004 Representatives are available to answer your questions Monday - Friday from 8:00 a.m. to 5:00 p.m.
tirescout.
tirescout.qxp 3/12/2012 10:34 AM Page 22 THE WHISTLER GROUP, INC. CORPORATE HEADQUARTERS 3604 NW Frontage Rd. Bentonville, AR 72712 TEL: 1-800-531-0004 FX: 479.273.2927 © 2012 The Whistler Group, Inc. www.whistlergroup.