WBU-900 User Guide BACK-UP CAMERA INSTALLS IN MINUTES Product Marketing Name: Camera Hardware Version Identification Number: WBU-900C Product Marketing Name: Monitor Hardware Version Identification Number: WBU-900M
INTRODUCTION Welcome Thank you for choosing a Whistler product. We are dedicated to providing products that represent both quality and value. Please read the User Guide carefully before using this product. If you have additional questions, please visit the FAQ page on our website at www.whistlergroup.com or call Toll Free (800) 531-0004 / Tel (479) 273-6012, 8am to 5pm CT, Monday through Friday to speak to a Customer Service Representative.
FEATURES Features • 4.
FEATURES 1 2 5 3 4 6 8 7 17 9 12 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 10 11 18 13 14 15 16 Monitor Camera Solar cell Solar cell Suction cup mount Dash disk Tie wraps License back-plate 4 Long screws (Domestic) 4 Long screws (Import) 11. 12. 13. 14. 15. 16. 17. 18. 19.
CHARGING CAMERA ASSEMBLY The Camera under normal use, will maintain a charge with exposure to sunlight. A battery status indicator is provided on the monitor when the camera is in use. If you’re storing your vehicle in a garage for more than a one month, or are otherwise not exposing the Camera to sunlight on a regular basis, you may need to recharge it via the Micro USB charge port. To recharge the Camera: 1. If attached to vehicle, please remove. 2.
ASSEMBLY / INSTALLATION Notice Some states or local governments may have regulations or laws that restrict the use of anything that might impair the clear view of a license plate. Check local laws for compliance These instructions are only meant as a general guide due to the number of different makes and models of vehicles. 1. 2. 3. 4. Remove license plate from vehicle and place on top of the supplied license backplate.
ASSEMBLY / INSTALLATION 5. 6. 7. 8. 9. With the solar mounts centrally positioned, apply pressure to set the adhesive tape. Peel the backing from the adhesive strips on the camera base and carefully slide onto the long edge of the license plate assembly positioned centrally between the license plate mounting holes. Remove the 2 short machine screws and nuts used earlier and set aside. Apply the 4 adhesive disks to the flat side on each of the 4 spacers.
ASSEMBLY / INSTALLATION 11. Reinsert the 2 short machine screws into the 2 holes if these are not used to attach to your vehicle, insert the machine nuts, then tighten. 12. If needed, 2 cushions are provided to protect your vehicle. Attach to the back of the spacers containing the machine nuts. 13. Connect the solar panel connectors to the mating connectors from the main camera housing and place the tie wrap adhesive pads as shown.
ASSEMBLY / INSTALLATION The camera angle should be adjusted to provide an optimal view of objects behind the vehicle. 15. Adjust the camera angle as required: • To adjust the camera angle, tilt the camera to the correct angle. • The camera should be adjusted to a horizontal position relative to the ground, so as to provide optimal view of objects behind the vehicle. • Carefully tighten the 2 screws ½ turn to prevent the camera angle from moving during vibrations from driving. 16.
ASSEMBLY / INSTALLATION 17. Clean and dry the mounting surface before applying suction cup or dash disk. 18. Press the suction mount against the mounting surface and push the suction lock lever down. Make sure it is attached securely. 19. Slide the monitor onto the monitor arm. The monitor angle can be adjusted by loosening the monitor angle adjustment knobs, tilting the monitor, then tightening the knobs. 20. Plug the monitor cigarette lighter/accessory socket power cord into a 12-volt DC power port.
OPERATION Testing the System 1. With power applied to the monitor, the button backlight will illuminate to indicate the monitor is ON and in Standby mode. 2. The Blue LED will blink briefly to indicate that it is attempting to communicate with the camera. When connected to the camera, the blue LED will turn solid. It may take a moment for the camera to begin sending the video information, allow time for the image to be displayed. 3.
OPERATION 5. 6. If your 12-volt DC power port is switched on with your ignition, the unit will automatically request an image from the backup camera each time you start your vehicle. When the vehicle is shut off, power is removed from the monitor and the button backlight will shut off. Route and secure all wires as needed.
FUNCTION Functions of the Touch Buttons (left to right) : Touch to enable or cancel the transmitter; Touch for 3 seconds to turn on/off the backup assist lines. Touch to select a corresponding function. : Touch to move to or adjust a corresponding function : Touch to enable/cancel the menu. : Touch to move to or adjust a corresponding function. : Touch briefly to turn on, Touch and hold for 3 seconds to turn on/off. Adjusting Monitor Settings: 1. Touch the button to bring up the Options. 2.
MONITOR SETTINGS Menu Operations: Enter the main Menu Interface and 4 options are available including Image Parameters, Image Rotation, Code Pairing and Software Information.
MONITOR SETTINGS Brightness/Contrast/Color Settings are similar. Take Brightness as an example, when Brightness is chosen, press or on the interface to adjust the brightness as shown above: Select “Image Rotation”, and then touch the button to rotate or mirror the image. (It is best to have a video image displayed when making this selection). Select “Code Pairing”, and touch the button to enter Code Pairing Mode; then, power on the camera by connecting the solar cell cables to finish the Code Pairing.
INFORMATION Battery Icon is on the top left corner of the monitor, and indicates the relative capacity of the built-in lithium battery when a video image is present. Signal strength of the received image is on the top right corner of the monitor when a video image is present.
TROUBLESHOOTING If the monitor does not turn on when power is applied: • Check to make sure the power source is active (if your cigarette lighter is switched with vehicle ignition, your monitor will only work when the vehicle is running or the key in the ON position). • Check to make sure the fuse and power cord are in working order • With power applied to the monitor, touch the power button.
DISCLAIMER The Whistler Digital Wireless Backup Camera is intended to assist responsible drivers, but it does not relieve a driver from full responsibility for the operation of the vehicle. It is the driver’s sole responsibility to avoid contact with any objects, animals, or persons.
CARE AND MAINTENANCE Cleaning Do not clean or wipe the Back-Up Camera with solvents or chemical materials. If necessary, remove dirt or stains using a soft cloth dampened with a mild detergent solution. Fuse Replacement 1. Turn the cap on the tip of the power plug counterclockwise (no tools needed). 2. Remove the cap, center pin and fuse. 3. Replace the fuse with a new 1-amp fuse. 4. Replace the center pin and cap. Turn the cap clockwise. Disposal The Back-Up Camera is designed to provide years of service.
FCC INFORMATION IMPORTANT: FCC (Federal Communications Commission) requirements state that changes or modifications not expressly approved by Whistler could void the user’s authority to operate the equipment. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
SPECIFICATIONS CAMERA Operational Current (when transmitting): <220mA Pixels: 640 x 480 View Angle: 110° Image Sensor: 1/4“ CMOS VGA Image Quality: Max 25 fps. TRANSMITTER Frequency: 2409.75 ~ 2472.75MHz RF transmission distance: >328 ft. (>100 m) Operation/storage temperature: 14° to 122°F (-10° to 50°C) MONITOR LCD display screen size: 4.3 in.
WARRANTY INFORMATION Consumer Warranty This Whistler product is warranted to the original purchaser for a period of one (1) year from the date of original purchase against all defects in materials and workmanship, when purchased from an authorized Whistler retailer. This limited warranty is void if the unit is abused, misused, modified, installed improperly, or if the housing and/or serial numbers have been removed.
WARRANTY INFORMATION Service Under Warranty During the warranty period, defective units will be repaired or replaced (with the same or a comparable model), at Whistler’s option, without charge to the purchaser when returned prepaid, with dated proof of purchase to the address below. Units returned without dated proof of purchase will be considered out of warranty and therefore are not covered by the described Limited Warranty. (Refer to Service Out-of-Warranty section.
WARRANTY INFORMATION IMPORTANT: Whistler will not assume responsibility for loss or damage incurred in shipping. Therefore, please ship your unit insured with return receipt requested. CODs will not be accepted! Include with your unit the following information, clearly printed: • Your name and physical street address for shipping (no PO Boxes), a daytime telephone number, and an email address (if applicable). • A detailed description of the problem (e.g.,“device will not power ON”).
WARRANTY INFORMATION Service Out-Of-Warranty Units will be repaired at “out-of-warranty” service rates when: • The unit’s original warranty has expired. • A dated proof of purchase is not supplied. • The unit has been returned without its serial number. • The unit has been misused, abused, modified, installed improperly, or had its housing removed. The minimum out-of-warranty service fee for your Whistler product is $65.00.
WARRANTY INFORMATION IMPORTANT: When returning your unit for service, be certain to include a daytime telephone number and an email address (if applicable). Customer Service If you have questions concerning the operation of your Whistler product, or require service during or after the warranty period, please call Customer Service at Toll Free (800)531-0004 Tel (479)273-6012 Representatives are available to answer your questions Monday - Friday from 8:00 a.m. to 5:00 p.m. (CT) or visit the FAQs at www.
IC Warning: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
CORPORATE HEADQUARTERS 1716 SW Commerce Dr. Ste. 8 Bentonville, AR 72712 Toll Free (800) 531-0004 TEL (479) 273-6012 www.whistlergroup.com CUSTOMER RETURN CENTER 1412 South 1st St. Rogers, AR 72756 Email: info@whistlergroup.com P/N 06M17 © 2017 The Whistler Group, Inc.
