How to install, operate and maintain your Demand Controlled Water Softener Do not return water softener to store If you have any questions or concerns when installing, operating or maintaining your water softener, call our toll free number: 1-866-986-3223 Monday- Friday, 8 AM - 7 PM EST or visit www.ecodynewatertreatment.com When you call, please be prepared to provide the model and serial number of your product, found on the rating decal, typically located on the rim below the salt lid hinges.
TABLE OF CONTENTS Page Specifications & Performance Claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Water Softener Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications & Performance Claims These models are efficiency rated. The efficiency rating is valid only at the minimum salt dose. These softeners have a demand initiated regeneration (D.I.R.) feature that complies with specific performance specifications intended to minimize the amount of regenerant brine and water used in their operation.
Water Softener Safety Your safety and the safety of others are very important. We have provided many safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
Inspect Shipment Remove and discard (or recycle) all packing materials. To avoid loss of small parts, we suggest you keep the small parts in the parts bag until you are ready to use them. The parts required to assemble and install the water softener are included with the unit. Thoroughly check the water softener for possible shipping damage and parts loss. Also inspect and note any damage to the shipping carton.
Installation Requirements LOCATION REQUIREMENTS PLUMBING CODES Consider all of the following when selecting an installation location for the water softener. All plumbing must be completed in accordance with national, state and local plumbing codes. = Do not locate the water softener where freezing temperatures occur. Do not attempt to treat water over 120ºF. Freezing temperatures or hot water damage voids the warranty.
Installation Requirements VALVE DRAIN REQUIREMENTS 1/4” NPT Thread Barbs for 3/8” I.D. Tubing Using the flexible drain hose (included), measure and cut to the length needed. Flexible drain hose is not allowed in all localities (check your plumbing codes). If local codes do not allow use of a flexible drain hose, a rigid valve drain run must be used. Purchase a compression fitting (1/4 NPT x 1/2 in. minimum tube) and 1/2" tubing from your local hardware store. Plumb a rigid drain as needed (See Figure 5).
Dimensions 19” 3-3/4” IN 18” OUT IN – OUT 47-7/8” 41-1/2” 39-1/2” FIG.
Installation Instructions TURN OFF WATER SUPPLY Nozzle Venturi Assembly 1. Close the main water supply valve, located near the well pump or water meter. Top Cover Brine Tank Overflow Elbow Nut Ferrule 2. Open all faucets to drain all water from house pipes. NOTE: Be sure not to drain water from the water heater, as damage to the water heater elements could result.
Installation Instructions COMPLETE INLET AND OUTLET PLUMBING Measure, cut, and loosely assemble pipe and fittings from the main water pipe to the inlet and outlet ports of the water softener valve. Be sure to keep fittings fully together, and pipes squared and straight. Be sure hard water supply pipe goes to the water softener valve inlet side. Electrical Shock Hazard Install metal ground clamp to metal house water supply pipe before beginning installation.
Installation Instructions TEST FOR LEAKS ADD WATER AND SALT TO THE SALT STORAGE TANK To prevent air pressure in the water softener and plumbing system, complete the following steps in order: 1. Fully open two or more softened cold water faucets close to the water softener, located downstream from the water softener. Excessive Weight Hazard Use two or more people to move and lift salt bags. Failure to do so can result in back or other injury. 2.
Programming the Water Softener TANK LIGHT button UP button Display SET SALT LEVEL button SET SALT LEVEL TANK LIGHT STATUS LIGHT (see below) OPERATING (Steady) PROGRAM PRESS TO SCHEDULE LOW SALT (Flashing) RECHARGE button HOLD TO START RECHARGE DOWN button PROGRAM button FIG.
Programming the Water Softener Salt Type allows you to choose between sodium chloride (NaCl), which is regular softener salt, or potassium chloride (KCl), which is an alternative to sodium chloride. KCl (potassium chloride) may be used if the user of the water softener is on a sodium restricted diet and is concerned about the amount of sodium in the water supply. continued from previous page 2. Press the r UP or s DOWN buttons to set your water’s hardness number.
Customizing Features / Options RECHARGE SET SALT LEVEL The RECHARGE button is used to initiate an immediate recharge. The water softener has a salt monitor indicator light to remind you to add salt to the storage tank. 1. Press and hold the RECHARGE button until the words “RECHARGE", “SERVICE" and “FILL" flash in the display. RECHARGE initiated NOTE: You must set salt level each time salt is added to the water softener. To set this monitor system: 1.
Customizing Features / Options POWER OUTAGE MEMORY SALT EFFICIENCY If electrical power to the water softener is lost, “memory'' built into the timer circuitry will keep all settings for several hours. While the power is out, the display is blank and the water softener will not regenerate.
Customizing Features / Options MAXIMUM DAYS BETWEEN REGENERATIONS CLEAN / CLEAR WATER IRON REDUCTION This feature is beneficial on water supplies containing ferrous (clear water) iron. The default setting is OFF. When this feature is set to ON, an additional backwash and fast rinse cycle will occur first, preceding the normal regeneration sequence. This provides extra cleaning of the resin bed before it is regenerated with the salt brine.
Routine Maintenance ADDING SALT CLEANING THE NOZZLE & VENTURI Lift the salt lid and check the salt storage level frequently. If the water softener uses all the salt before you refill it, you will experience hard water. Until you have established a refilling routine, check the salt every two or three weeks. Always add if less than 1/4 full. Be sure the brinewell cover is on. NOTE: If using potassium chloride (KCl), do not fill above level 4 on the brinewell decal.
Troubleshooting AUTOMATIC ELECTRONIC DIAGNOSTICS 3. Symbols in the display indicate POSITION switch operation (See Figure 35). This water softener has a self-diagnostic function for the electrical system (except input power and/or water meter). The water softener monitors electronic components and circuits for correct operation. If a malfunction occurs, an error code appears in the display. Switch is open (Cam not rotating) Switch is closed (Cam rotating) FIG. 35 4.
Troubleshooting RESETTING TO FACTORY DEFAULTS 2. After observing fill, press the RECHARGE button to move the softener’s valve into the brine position. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level. This may take 15 to 20 minutes. To reset the electronic controller to its factory default for all settings (time, hardness, etc.): 1.
Softener Exploded View 12 27 Valve Assembly See Pages 22 & 23 for parts 13 121 28 1 2 3 15 123 4 14 6 5 16 7 17 10 18 8 19 23 9 8 20 21 7 11 6 5 22 25 24 26 29 20
Softener Parts List Key No. Part No. – 7112963 1 á 3 á 2 4 5 7077870 7105047 6 á 7161849 7247996 11 7327568 7310202 7275907 13 7335163 14 7267116 ¢ 16 O-Ring, 2-3/4” x 3” 17 Top Distributor 18 Repl. Bottom Distributor 19 Tank Neck Clamp Kit (includes 2 ea. of Key Nos. 6 & 7) Retainer Clip (2 req.) á 0502272 12 ¢ Clamp Section (2 req.) 9 10 15 O-Ring, 13/16” x 1-1/16” á 7331177 8 Distributor O-Ring Kit (includes Key Nos. 1-3) O-Ring, 2-7/8” x 3-1/4” – 7 Key No.
Valve Exploded View 100 101 102 144 103 143 104 105 142 106 141 140 139 138 110 117 cross-section view 118 126 135 122 112 seal 136 108 111 wear-strip 137 109 107 113 134 121 114 133 132 115 119 130 131 129 123 120 127 116 125 128 22 124
Valve Parts List Key No. Part No. Description 100 7224087 Screw, #8-32 x 1” (2 req.) 102 7231393 Motor Plate 101 103 104 105 7286039 0900857 7171250 7283489 – 7331169 106 á 108 á 107 109 110 á á 115 116 á á 119 7171187 7185500 120 7129889 122 7271204 123 7089306 7311127 7290931 124 á Turbine & Support Assembly (includes 1 ea. of Key Nos. 124, 125 & 2 ea. of Key No.
EXTEND YOUR WARRANTY: Use Whirlpool™ WHE-WSC Water Softener Cleanser The factory warranty for your water softener is shown below. The one year full warranty period on parts and labor can be extended to two years from the date of purchase if you use Whirlpool™ WHE-WSC Water Softener Cleanser on your system. Use one bottle of Whirlpool™ WHE-WSC Water Softener Cleanser, as directed, every four months from the date of purchase of the water softener.