Installation Instruction Whirlpool Systems Whrilpool Whirlpool Whrilpool Whrilpool Whirlpool Whrilpool Whrilpool Whrilpool Whrilpool Whrilpool Whrilpool Whrilpool Moneva 300 L Moneva 300 R Iseo 320 Victoria 325 Teslin 330 Lugano 340 Imandra 350 Imandra 355 Ladoga 360 Malawi 370 Almonte 380 Manitoba 390 21500000/21502000 21509000/21511000 21518000/21517000 21531000/21532000 21522000/21523000 21524000/21525000 21527000/21529000 21533000/21534000 21536000/21538000 21540000/21541000 21545000/21547000 215490
Contents English Fittings..........................................................................................................................................................................3 Installation Instructions ....................................................................................................................................................4 Service Hatch and Air Supply..............................................................................................................
Fittings Included loose Pool control (housing) Siphon + flat seal Air control grip Hand shower English – – – – – 3-hole-armature grips (option) – Secu-Box (Option) Whirlpool Series 300 1. Water nozzle 2. Air nozzle 3. Air hoses 4. Pool control 5. Air control 6. Air supply 7. Water sensor 8. Drain and overflow set 9. Water pump 10. Air blower 11. Bath supporting frame and feet Whirlpool Series 700 1. Water nozzle 2. Air nozzle 3. Air hoses 4. Pool control 5. MultiAirControl 6. Solenoid valve 7.
Installation Instructions ATTENTION! LIFTING: Always lift bath at support or bath rim. Never use fitted hoses or installation parts to lift the bath. INSPECTING: Check whirlpool after receipt for damage. Contact your dealer immediately if you notice any damage. We do not assume liability for damage occurring during or after installation. Read check points: Thoroughly read Installation and Operating Instructions before starting installation.
Service Hatch and Air Supply grid is Service hatch and air supply Position service hatches, at least 40 x 40 cm, near the motor and blower depending on the model. Position service hatches so that parts such as blowers, pumps, valves, connector boxes and other connections are always accessible and replaceable. Removable side panels are ideal (e.g. Mepa decorating system). The air grid for the blower air supply (150 cm2) can be installed in this service hatch.
Surface Set Air Control and Pool Control Installation (Whirlpool Series 300) 6
English Surface Set Multi Air Control and Pool Control Installation (Whirlpool Series 700) 7
Surface Set Bath Rim Thermostat Installation (Option) 1 Insert shower hose sleeve seal in hand shower. 5 Shut-off/diverter valve: Check if closed. If not, close it so that no more water flows. 2 Connect shower hose to hand shower. Fit for shut-off and diverter valve. 3 Lay hand shower in bath. 4 Turn water on. 8 6 Push the snap-in fit on when closed so that the nose points to the middle of the bath.
Surface Set Bath Rim Thermostat Installation (Option) English 7 Fill via Exafill, adjust temperature. 8 Test temperature, set thermostat to 38 °C.
Electrical Wiring Diagrams Series 300 Blower and hydraulic pump 10
Electrical Wiring Diagrams English Series 700 Blower, Hydro pump and pulsation 11
Electrical Wiring Diagrams Series 300 Automatic underwater lighting (optional) ON/OFF (automatic via water sensor) 12
Electrical Wiring Diagrams English Series 700 Automatic underwater lighting (optional) ON/OFF (automatic via water sensor) 13
Electrical Wiring Diagrams Series 300 Heating (optional) 14
Electrical Wiring Diagrams English Series 700 - 770 Heating (optional) Series 780/790: 2 x 230 V/16 A 15
Electrical Wiring Diagrams Series 300/700 Hydro cleaning (optional) 16
General Information Bath Care Instructions Wellness starts in the bathroom Wellness starts in the bathroom. It is obvious, when you feel clean, you feel well. You feel even better when just the contact with the element water becomes a pure pleasure. For example, with the whirlpools from Pharo. The movement of the water stimulates the circulatory system, you feel light and unburdened, muscular pain and tensions disappear in a pleasant manner.
Whirlpool 300 Operation Operation and Functions Whirlpool Series 300 for Pool Control Exafill The innovative drain system Exafill supersedes the usual draining method by integrating three functions in one: Exafill is bath inflow, bath drain and bath overflow all in one! Attention! According to the DVGW (German Association of Gas and Water Specialists) standard, an on-site pipe interrupter must be available when the Exafill is connected. Check water circuits according to local regulations.
Whirlpool 300 Operation Hydro on/off (button 4, Fig. 1) The Hydro system is switched on by pressing this button. A light by the button turns on. Water is sucked from the bath near the drain area and pumped into the bath again via the side nozzles. The system is switched off when the Hydro button is pressed again. Attention: The system only operates when the water level in the bath is at least 5 cm above the water top nozzles. A sensor controls the water level. Air control (Fig.
Whirlpool 700 Operation Operation and Functions Whirlpool Series 700 for Pool Control Exafill The innovative drain system Exafill supersedes the usual draining method by integrating three functions in one: Exafill is bath inflow, bath drain and bath overflow all in one! Attention! According to the DVGW (German Association of Gas and Water Specialists) standard, an on-site pipe interrupter must be available when the Exafill is connected. Check water circuits according to local regulations.
Whirlpool 700 Operation Hydro on/off (button 4, Fig. 1) The Hydro system is switched on by pressing this button. A light by the button turns on. Water is sucked from the bath near the drain area and pumped into the bath again via the side nozzles. The system is switched off when the Hydro button is pressed again. Attention: The system only operates when the water level in the bath is at least 5 cm above the water nozzles. A sensor controls the water level. Fig. 1 MultiAirControl (Fig.
Options Options for Whirlpool Series 300/700: • Underwater lighting • Hydro bath heating 1.5 kW (3 kW for Whirlpool Series 780/790) • Hydro cleaning • Bath rim thermostat (bath rim thermostat, hand shower, Exafill, shut-off and switch-over) • Grabrails Underwater lighting The underwater halogen lamp in attractive design creates a very special bathing atmosphere. The 12V underwater lighting is automatically controlled by a water level sensor.
Hydro cleaning The built-in water nozzles connected to the water supply are flushed with fresh water after the whirl bath. Activating the Hydro cleaning button (button 6, Fig. 1) after a bath flushes the Hydro circuit through with cold water (empty bath first). A LED in the button signal Hydro cleaning operation. Cleaning takes approx. 5 minutes when the bath is completely empty. Attention: Hydro cleaning needs an additional 1/2“ water connection (cold water) with subsequent check valve.
A i r S y s t e m Tr o u b l e s h o o t i n g 24
English Automatic S y s t e m S t a r t i n g Tr o u b l e s h o o t i n g 25
H y d r o S y s t e m Tr o u b l e s h o o t i n g 26
English U n d e r w a t e r L i g h t i n g Tr o u b l e s h o o t i n g 27
Whirlpool 300 Spare Parts 1 2 3 4 11 12 10 5 6 14 7 9 13 Pos. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Description Poolcontrol cpl. cable with plug (11 leads) cable with 2 plugs (7 leads) escutcheon handle shut off unit, Elastop escutcheon Ø 53 mm non return valve DW 15 water level sensor hydro pump capacitor for hydro pump blower cpl. cable with plug (5 leads) blower cpl. with control WDI 1 control WDI 1 cross fitting cpl.
Whirlpool 300 Spare Parts 9 1 English 10 8 2 pressure control no longer 5 available 4 11 7 6 3 Pos. 1 2 3 4 5 6 7 8 9 10 11 Description solenoid valve for hydro cleaning solenoid valve membrane for hydro cleaning solenoid coil for hydro cleaning 230 V 60 Hz 10 W No. 18650 reheater 1,5 kW reheater 3,0 kW switch box cpl. WDI 2 switch box cpl.
Whirlpool 700 Spare Parts 11 1 2 3 10 4 12 9 5 6 8 13 Pos. 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Poolcontrol kpl. Kabel mit Stecker (11 Adern) Rosette Griff "Quattro" Einsatz kpl. Rosette Wasserstandsensor Hydropumpe Kondensator für Hydropumpe blower cpl. electronics for blower cable with plug (5 leads) cross fitting cpl.
Whirlpool 700 Spare Parts 9 1 English 10 8 2 pressure control no longer 5 available 4 11 7 6 3 Pos. 1 2 3 4 5 6 7 8 9 10 11 Description solenoid valve for hydro cleaning solenoid valve membrane for hydro cleaning solenoid coil for hydro cleaning 230 V 60 Hz 10 W No. 18650 reheater 1,5 kW reheater 3,0 kW switch box cpl. WDI 4 relay box for reheater pressure control spare bulb 12 V / 50 W spare bulb 12 V / 20 W escutcheon Ø 85 mm escutcheon Ø 60 mm bent outlet plug hair guard tray transformer f.
Form-Nr. 9.08843.01 Hansgrohe · Postfach 1145 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax +49 (0) 7836/511440 E-Mail: info@hansgrohe.com · Internet: www.hansgrohe.