InstructionS WHIRLPOOL UNDERCOUNTER WATERFILTRATION SYSTEMSI, II, & Ill m 1
Remove parts from packages. Check that you have all the parts.
BeforeYouStart. . . IMPORTANT: Read and save these instructions. It is recommended that this system be installed by a licensed plumber. It is the responsibility of the installer to comply with the installation specifications provided and with state and local plumbing codes. If you decided to install the system yourself, see “General Information” on page 9 before continuing. Water Filtration Svstems I. II and Ill can be installed in the basement if there is not adeqiate room for under-sink installation.
Instructions At A Glance For detailed instructions see following page. l 1.Turnoff cold watersupply.(St; la-lb) Electrical Shock Hazard Special care must be taken when drilling into water pipes. Some water may remain in water supply pipe: If an electric drill is used, it must be properly grounded to prevent severe or lethal shock if water should enter drill. Use only an electric drill that is double insulated or properly grounded.
Product Damage DO NOT connect to a hot water supply line. Failure to follow this instruction could result in product damage. Take note of water requirements listed under . the Use & Care section of this booklet. The filtration system’s feed line (orange tubing) connects to your cold water supply line using the saddle valve. Do not use saddle valve if it is prohibited by your state or local plumbing codes. The saddle valve is for use with 3/s” to s/B”outer diameter (O.D.
Instructions At A Glance For detailed instructions see following page. l 1. Decideif the systemwill be connectedto your refrrgerator,to an optionalfaucetor to both. (Step2a) 2. Connectrefrigerator’swatersupplyto filtration assemblywith bluetubing.(Steps2b-2c) 3. Or,insta!lfaucetin sink and connectbluetubing to filtration assembly.(Steps2d-2g) 4. Or,use “T” greyconnectorto connectboth refrigeratorand faucet.
2a You have three installation options: . 1.Connect water supply from filtration system to refrigerator’s ice and water only. 2.Connect water supply from filtration system to optional sink faucet only. 3.Connect water supply from filtration system to both refrigerator and optional sink faucet. All parts are included with this kit to connect refrigerator. If you choose to connect filtration system to a sink faucet, order sink faucet, Part No. 4319154, available from your Whirlpool dealer.
StartUp Instructions At A Glance For detailed instructions see following page. l i . I 1. Slidefiltration assemblyonto mountingscrews. (Steps3a-3c) 2. Turnon cold watersupply.(Step3d) 3. If filtration assemblywasconnectedto refrigerator, makeand discard2 batchesof ice and drain 2-3gallonsof waterfrom waterdispenser.(Step3e) 4. If filtration assemblywas connectedto sink faucet,lift faucethandleto discard2-3gallonsof water.
StartUp 3d Electrical Shock Hazard Special care must be taken when drilling into walls. Electrical wires may be concealed behind the wall covering: - Use only an electric drill with a 3-wire power supply cord connected to a grounded receptacle. Check with qualified electrician if you are in doubt as to whether your electric drill is properly grounded. Failure to follow these instructions could result in personal injury or death. Place a towel or bucket under saddle valve, .
WaterRequirements The filtration system must be connected to a cold water supply line providing 30-l 00 psi water pressure. The water temperature must be between 40”-100°F. Community or private well water must be potable (suitable for drinking). Personal Injury Hazard DO NOT use water filtration system if water is microbiologically unsafe or water quality is unknown. Failure to follow these instructions could result in personal injury.
Call l-800-253-1301 to order. WATER FILTRATION SYSTEM I MODEL NO. WSClOOYW ReplacementParts & Accessories System I Replacement Cartridge Kit includes Sediment/Carbon REPLACEMENT Kit (SC) Cartridge 4373529 System II Replacement Cartridges Kii Kit includes Lead Reduction (L) and Carbon Filter (CF) Cartridges. Cartridges can also be ordered individually. Lead Reduction THIS PRODUCT HAS BEEN TESTED AND LISTED UNDER NSF STANDARD REDUCTION (CLASS I) AND PARTICULATE REDUCTION (CLASS II).
Performance DataSheet 0 NSFB 0 This product has been tested and listed by NSF International under Standard 42 for Taste, Odor and Chlorine reduction (Class I) and Particulate reduction (Class II). NSFB Whirlpool Water Filtration System I Whirlpool Water Filtration System II Model No. WSClOOYW Model No. WSCPOOYW SPECIFICATIONS: Taste/Odor/Chlorine reduction (Class I) CAPACITY: 1,000 Gallons SERVICE FLOW RATE: 0.6 GPM (2.
Performance DataSheet Systems I, II & Ill This product has been tested and listed by NSF International under Standard 42 for Taste, Odor and Chlorine reduction (Class I) and Particulate reduction (Class II) and under Standard 53 for Cyst, Turbidity, Lead and VOC reduction. APPLICATION GUIDELINESMATER Whirlpool Water Filtration System Ill SPECIFICATIONS: Lead, VOC and Taste/Odor/Chlorine reduction (Class I) CAPACITY: 500 Gallons SERVICE FLOW RATE: 0.6 GPM (2.
Part No. 4373576 01993 Whirlpool Corporation Whirlpool Corporation Benton Harbor. Ml 49022 CB Printed on Recycled Paper in U.S.A.
