Before Using Your New Vacuum Kenmore Vacuum Cleaner Warranty important Safely Instructions Parts and Features Assembly Instructions Use .. Vacuuming Tips Suggested Pile Height Settings . Attachments, Attachment Use Chart Performance Features Please read this guide. [will help you assemble and operate your new Kenmore vacuum in the safest and most effective way. Power-Mate® Care Dirt Sensors A Belt Changing and Agitator Cleaning . . 10-11 Light Bulb Changing . Agitator Servicing . Troubleshooting .
WARNING Read all instructions in this manual before assembling of Rising your vacuum cleaner. Use your cleaner only as described in this manual, Use only with Sears recommended achievements. Disconnect dialectical supply before servicing or cleaning out brush area. Failure fo do so could result in electrical shay or brush suddenly starting. Bo rot leave cleaner when plugged in. Unplug from outlet whee not In Use and before servicing.
iris important to know your vacuum cleaners pairs and features to ensure iis proper and safe use. Review these before using your cleaner, Hem Part No. Part No.
WARNING Electrical Shock Hazard PO NOT plug into electrical supply until assembly is complete. Failure te do so could result in electrical shock or injury. 1. insert wand(s} into Power-Mate® until the wand bunions snap into place. Site Height Port 1. Lower wand from upright position by pressing on the handle release pedal. To remove: Step on wand quick release pedal, then pull up on wands. Anon CAUTION DO NOT leave the Power-Mate® running in one spot in the upright position for any length of time.
Suggested sweeping pattern. For best cleaning action, the Powse-Mate® should be pushed straight away from you and pulled straight back. At the end of each pul stroke, the direction of the Power-Male® should be changed to paint into the next section to be cleaned, This pattern should be continued across tha carpet with slow, gliding motions, Hi NOTE: Fast, jerky strokes do not provide 2 complete clean. ~N\ boy CAUTION Product Damage Hazard Use care If the Power-Mate® and wand is left iis the upright position
2. Press wand quick Wand lager pedal with foot and pull the wands a straight up and out of {Hed Power-Mate®. i Some Models: The Power-Mate® plug and cord do not have: 10 be removed fo use CAUTION DG NOT attach or remove handle or wands while cleaner is ON. This could cause sparking and damage ihe electrical contacts, attachments on the 1. To remove wands from Power-Mate®, 3. Put attach lock wands In meets on straight-up wands as need position. od, See ATTACHMENT USE CHART.
EDGE CLEANER | j Ag live brush edge cleaners are on both sides of ihe Power: Mate®. Guide either SIDS of the Power Mate® along baseboards ar next io furniture to help romaine dirt rapped at carpet edges. OVERLOAD PROTECTOR The Power-Mate® has built-in protection Overload Protector against motor and Reset Bern od belt damage should << the agitator jam. it the agitator slows down or stops, the overload —, protector shuts off the — Powar-Mate®, The artiste motor will continue to run.
Always follow all safety precautions when cleaning and servicing the Powar-Mate®. Although the dirt sensor feature in your Kenmore Power-Male® is designed for years af trouble free use, the passage of dirt through the air passage system oan coat the lens causing the green light to come on and stay on never switching to red. When this happens the Ens must be cleaned. CAUTION Never use water or any cleaning solution when cleaning the lenses.
TO REMOVE BELT 1. Turn Power Mate® upside down, 2. Unscrew ihe wo @ Power Mate” cover screws, 3. Turn Power Mate” right side up. Press handle release petal and dower the swivel, Lift rear fiches up. 4. To remove cover, grasp ihe sides and pule out. 5. Lift agitator assembly out and remove worn belt, End Gap 6. Check and clean end cap areas, See AGITATOR ASSEMBLY for picture of complete agitator assembly.
TO REPLACE BELT 1. install new belt over motor drive, then over brush sprocket. Agitator End Gap NOTE: See PARTS AND FEATURES for belt number. 2, Place agitator assembly back info Power-Mate®. 3. Line up front of cover and base. Fest cover on front edge of base as shown. 4, NOTE: On dirt sensor models be sure that the board Is upright and the wires are tucked back as shown. BET 11 ESI Rotate cover AS back. Press Ci cover firmly unt side and rear tabs snap info Side Rear Fatah Notches place.
WARNING Electrical Shock Or Personal injury Hazard Disconnect electrical supply before servicing or cleaning the unit. Failure to do 50 could result in pretrial shock or personal injury from cleaner suddenly starting. TO CHECK AGITATOR ASSEMBLY minutemen Sol When brushes CTT pr ee 878 WOM level of the base Ee {EE 4 support bars, replace the mE Agitator assembly. Base Support Bars TO REPLACE AGITATOR ASSEMBLY 1. Remove Power-Mate® cover, bait and agitator assembly.
PARA RETIRAR LA CORREA 1. Cojearse I Poner Hae” con la parte inficionar hala arriba. 2. Quite fos dus (2) tornillos en fa Cubre do fa Power-Mate™ 3. Coloque & Poderdante” enea ‘pasioncilla vertical. Agríate of pedal del manga de racionero y baje la articulación giratoria. Levanta los Posibilito Basilios astiles raseros. elaterios Traseros 4. Para guitar 1a cubrirle ta, agarre fos lados ¥ tire afuera. 5. Levanto f unidad dsl agraviador quite la cor Tea astada, Tapa de} arromo 6.
Your Home For repair in your home of all major brand appliances, fawn and garden equipment, or heating and cooling systems, rio matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-i-yourself. For Sears professional installation of home appliances and rems like garage door openers and water heaters, 1-800-4-MY-HOME® Anytime, day ar night {1-B00-469-4663) {USA and Canada) WHWSOAE.0OM VPALEBAIS.