T-BOX DECORATIVE COOKER HOOD AKR600IX / AKR900IX INSTRUCTION MANUAL
Dear Customer, If you follow the recommendations contained in this Instruction Manual, our appliance will give you constant high performance and will remain efficient for many years to come.
RECOMMENDATIONS AND SUGGESTIONS INSTALLATION * The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. * Please read this instruction manual before installing and using this cooker hood. Properly keep this instruction manual in a safe place for future reference. * This cooker hood can be used either in the Ducted Mode (ducting fumes to the outside) or in the Recirculation Mode (internal recycling). The choice of modes can be left to customers.
* Deep fat fryer must be continuously monitored during use: overheated oil can burst into flame. * The hood should not be used by children or person not instructed in its correct use. MAINTENANCE * Proper maintenance of the Range Hood will assure proper performance of the unit. * Disconnect the hood from the main supply before carrying out any maintenance work. * Clean and/or replace aluminum grease filters and activated charcoal filters after specified period of time.
* The discharge air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels. CHARACTERISTICS DIMENSIONS COMPONENTS Ref Q’ty Product Components 1 1pc 2 1set Telescopic Chimney comprising 2.1 1pc Decorative Chimney Top 2.
9.a 5pcs Mounting Screws (ST 5 X 50MM) 9.b 2pcs Chimney Mounting Bracket Screws (M 4 X 10 MM) 9.
INSTALLATION & USE Note 1 : On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and chimney prior to final installation. Note 2: At least two people will be required to mount the hood. WALL DRILLING AND BRACKETS FIXING (X=Y-260) 1. Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. 2.
DAMPER (FLAPS) FIXING 1. Fix the damper (flaps) into the air outlet adapter. 2. To be sure that the damper (flaps) is locked well on the air outlet adapter, it should be flexible in opening and closing. DUCT FIXING Caution: To reduce the risk of fire, use metal ductwork only. 1. Attach an adequate length of 150mm round duct into the recessed area of the air outlet adapter. 2. Secure the duct using two screws that have been already fixed on the two sides of the air outlet adapter.
Recirculation Mode Caution: Do not use plastic or rigid metal ducting. 1. Determine the length of the compressed flexible aluminum ducting. Attach an adequate length of 150mm round duct to the air outlet adapter. 2. Install the charcoal filter on. 3. Please note that the air will flow out from the two grids on the sides of the decorative chimney top. Electrical Connection * Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards.
OPERATION OF CONTROLS The hood is operated using the push button on the front panel. The light switch turns the lamps on and off. The blower switch turns the blower on to three speed settings: 0 - OFF 1 - LOW SPEED 2 - MEDIUM SPEED 3 - HIGH SPEED 4 – LIGHT MAINTENANCE GREASE FILTER * The grease filters should be cleaned frequently (every two months of operation, or more frequently for heavy use). Use a warm detergent solution. * Grease filters are washable. 1.
HALOGEN BULBS This range hood requires two halogen bulbs (Type JCD, 12V, 20W Max, G-4 Base) WARNING: Always switch off the electrical supply before carrying out any operation on the appliance. To change bulbs: by using the flat screw driver. 1. Kick off the halogen bulb cover 2. Remove the bulb by pulling sideward (DO NOT ROTATE). 3. Replace with Type JCD, 12V, 20W Max, G-4 Base halogen bulb. Do not touch replacement bulb with bare hands ! CAUTION: 1.
HOOD CLEANING Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its fine appearance. Cleaning tips: * Hot water with soap or detergent is all that is usually needed. * Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks. * For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth.
TROUBLE SHOOTING The cooker hood may not work or work improperly. Before calling the After-sales service, switch off the appliance, unplug the power supply and refer to this guide to determine the problem. Status Reasons 1. No response of the lamps and the motor The plug is off from lamp doesn’t work 2. The power cord is body gives The fuse on the PCB Replace the fuse on the PCB board. Repair or replace the switch. The lamp is damaged. Replace the damaged lamp.
WARRANTY CARD At the purchase of the appliance properly fill out the product warranty card and properly keep it after having it signed and stamped by the dealer in order to use it in case of need of maintenance service.
