Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesADG 8473 FD

EN -1-

Chart

(see at right for options description)

PROGRAMS SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle push Start button and

close the door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options)

and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the

appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information

on the EN/Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

* Power consumption in: Left-on mode: 0.70 W / Off-mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Sensor 40-70°C

Delay

Antibacterial

rinse

Half Load

Recommended program for

routine washes, with dried-on

food.

X 7-15 1.00-1.70 70-172 Full

Pre-Wash cold

Delay Crockery to be washed later. — 4.0 0.01 14-16 NO

Fragile 40°C

Delay

Light soiling, for example glasses

and cups.

X 10.5 0.85 105-114 Light

Rapid 45°C

Delay

Lightly soiled crockery, with no

dried-on food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay

Antibacterial

rinse

Half Load

Normally soiled crockery.

Standard Program the most

efficient in terms of its combined

energy and water consumption.

X 11.0 0.92 240 Full

Fast Daily 60°C

Delay

Antibacterial

rinse

Half Load

Normally soiled crockery. X 11.0 1.30 80-95 Full

5019 300 01104

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

SALT INDICATOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

ANTIBACTERIAL RINSE

This function activates an

antibacterial rinse at the end of

the wash cycle, guaranteeing a

further reduction of bacteria.

Press the button to activate or

deactivate the function.

This function can be used with

the programs indicated in the

table of programs.

The dishwasher door must be

kept shut for the entire

duration of the program in

order to guarantee reduction

of bacteria.

If the door is opened the

indicator lamp starts flashing.

TABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent

used. Push the Tablet

button for 3 seconds

(until the indicator lights

up) if you are using the

combined detergents in

tablet (rinse aid, salt and

detergent in 1 dose).

If you are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press

of the button, the

delayed start indicator

increases by one hour

and after 24 restarts

from 0. Then press the

START button.

The dishwasher will

start after the set time.

RINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

HALF LOAD BUTTON

Half load cycle can be used for the

upper or lower rack.

Select the required program then

press the “Half Load” button – the

light comes on.

Turns off at the end of the program.

The “Half Load” option can be used

with the programs indicated in the

table of programs.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

Quick reference guide

Whirlpool is a regitered trademark of Whirlpool USA

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED. (see at right for options description) PROGRAMS SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups / long utensils / stemmed glasses. A - CLOSED A - OPEN B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. TO OPEN A: CLICK! C D How to remove the upper rack (if available) It could be useful to remove the upper rack to load bulky items in the lower rack.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open. To pause the program (e.g.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. How the faults are shown on the display: Function number “F”x - blinking The appliance... ...is not working/will not start - The appliance must be switched on. - Check the household circuit fuse if there is no power supply.
PAGE 7
What to do if... Crockery and cutlery... Possible causes... Solutions... ...salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up. ...have deposits: regeneration salt residue - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. ...
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.