Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesADG 2020 FD

EN -1-

Chart

(see at right for options description)

PROGRAM SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the program.

When the door is opened during a washing cycle, the

cycle is temporarily paused: the Start indicator blinks.

To resume the cycle push Start button and close

the door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute.

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1) Program data obtained under normal conditions and with default options on. Data may vary depending on ambient conditions and used options. Differences of up to

20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard

loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

Power consumption in: Left-on mode: 1.50 W / Off-mode: 0.50 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

6th Sense

PowerClean

40°-70°C

Use for normal soiled dishes with dried-on food.

Senses the level of soiling on the dishes and adjusts

the program accordingly. When the sensor is

detecting the soil level an animation appears in the

display and the cycle duration is updated. The

PowerClean

option is activated automatically with

this program. To deactivate, press the PowerClean

button on the control panel.

7.5-13 0.95-1.45 85-165

Pre-Wash cold

Crockery to be washed later. 4.0 0.01 14-16

Fragile 40°C

Light soiling, for example glasses and cups. 10.5 0.85 105-114

Rapid 45°C

Lightly soiled crockery, with no dried-on food. 11.0 0.85 30-50

Eco

50°C

Normally soiled crockery.

Standard Program the most efficient in terms of its

combined energy and water consumption.

10.0 0.822 200

1 hour

Wash & Dry

55°C

Light to normally soiled crockery.

Suitable for non-dried and fresh soiling.

11.0 1.30 60

Daily 60°C

Normally soiled crockery. 11.0 1.15 80-90

Intensive 65°C

Recommended program for heavily soiled crockery,

especially suitable for pans and saucepans.

15.0 1.60 145-155

Silent 50°C

Normally soiled crockery, gentle and

quiet thanks to the lower spray pressure.

14.0 1.20 290-299

P10

Steam

Program including steam action dedicated for heavily

soiled crockery, pots and pans. Soaking or hand

pretreatment is no longer needed.

14.5 1.75 165-175

—

POWERCLEAN

Thanks to the additional

power jets this option provides a

more intensive and powerful wash

in the lower rack, in the specific

area.

POWERDRY

This technology generates

outstanding drying results thanks

to a condensation process that

occurs inside the dishwasher.

PowerClean® active

PowerDry® active

Both options active

No options active

DELAYED START

BUTTON

Push the button

(repeatedly) to

delay the start of

the program.

Adjustable from

1to 24 hours.

With each press of

the button, the

delayed start

indicator increases

by one hour and

after 24 restarts

from 0.

Then press the

START button.

The dishwasher will

start after the set

time.

501930002222A

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING

THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER

30 SECONDS IF NO CYCLE HAS STARTED.

OPERATION

INDICATOR

A LED light projected on

the floor indicates that

the dishwasher is

working.

RINSE AID INDICATOR

When lit (at the end of the cycle), the

rinse aid dispenser needs to be refilled.

SALT INDICATOR

When lit (at the end of the cycle), the

salt reservoir needs to be refilled.

TABLET INDICATOR

See TABLET setting in

MULTIZONE description.

MULTIZONE

Allows you to choose the washing

zones. Press this button

(repeatedly) to select the wash

zones:

TABLET SETTING

This setting allows to optimize the

cycle performances according the

type of detergent used.

Push the MULTIZONE button for

3 seconds (until the indicator lights

up) if you are using the combined

detergents in tablet.

If you are using powder or gel

detergent, the Tablet indicator on

the control panel has to be off.

both racks

only upper rack

only lower rack

( - indicator lights)

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time

(h:min).

With “Delayed start” selected it indicates the time

remaining until program start (h.00) - below 1h

(0:min).

If “Fx Ey” messages appears on the display, see page 6

- chapter “What to do if...”.

Quick reference guide

Whirlpool is a registered trademark of Whirlpool USA

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! (see at right for options description) PROGRAM SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” below. START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). - Press and hold together and buttons for minimum 3 seconds. - The current water hardness setting will be visible on the display. - Press the button to increase setting.
PAGE 3
Daily check Adding rinse aid. How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups/long utensils/stemmed glasses. A - CLOSED A - OPEN TO OPEN A: B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. CLICK! How to adjust upper rack height (if available). It could be useful to lift up the upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. For hygienic reasons it is recommended to run at least once per month a high-temperature cycle (e.g. Intensive 65).
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes... Solutions... salt indicator is lit - rinse aid indicator is lit - Rinse aid dispenser is empty. - Refill dispenser with rinse aid (for more information - see page 3) ...
PAGE 7
What to do if... Crockery and cutlery... ...have deposits: regeneration salt residue Possible causes... Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. - Not enough rinse aid. - If you use a combined action detergent, try adding more rinse aid. - Plastic containers dry badly.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.