Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashers9BRVW6002A

EN -1-

Chart

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle, the

cycle is temporarily paused: the Start indicator blinks.

To resume the cycle push Start button and close the

door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

PROGRAM SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program

number is shown on the

display (P1...Px) – see “Table

of programs” below.

(see at right for options description)

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary

depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration

system.

2) Reference program for energy label in compliance with EN 50242 regulations.

* Power consumption in: Left-on mode: 1.27 W / Off-mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Sensor 40°-70°C

Delay

Half load

Recommended program for

routine washes, with dried-on

food (e.g. EN 50242).

X 7-15 1.00-1.70 70-172 Full

Pre-Wash cold

Delay Crockery to be washed later. – 4.0 0.01 14-16 NO

Fragile 40°C

Delay

Light soiling, for example glasses

and cups.

X 10.5 0.85 105-114 Light

Rapid 45°C

Delay

Lightly soiled crockery, with no

dried-on food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay

Half load

Normally soiled crockery.

Standard Program the most

efficient in terms of its combined

energy and water consumption.

X 11.0 1.03 170 Full

Fast Daily 60°C

Delay

Half load

Normally soiled crockery. X 11.0 1.30 80-95 Full

5019 600 00811

Options and display description

SALT INDICATOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

RINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

TABLET SETTING

This setting allows to optimize

the cycle performances

according the type of

detergent used.

Push the Tablet button for

3 seconds (until the indicator

lights up) if you are using the

combined detergents in tablet

(rinse aid, salt and detergent in

1dose).

If you are using powder

detergent or liquid detergent,

the Tablet indicator on the

control panel has to be off.

HALF LOAD BUTTON

Half load cycle can be used for

the upper or lower rack.

Select the required program

then press the “Half Load”

button – the light comes on.

Turns off at the end of the

program.

The “Half Load” option can

be used with the programs

indicated in the table of

programs.

DELAYED START BUTTON

Push the button (repeatedly) to

delay the start of the program –

delay indicator turns on.

Adjustable from 1 to 24 hours.

With each press of the button,

the delay increases by one hour

and after “h 24” returns to

“h 00”.

Then press the START button.

When this option is selected the

delay indicator turns on.

The dishwasher will start after

the set time.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! (see at right for options description) PROGRAM SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) – see “Table of programs” below. START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups / long utensils / stemmed glasses. A - CLOSED A - OPEN B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. TO OPEN A: How to adjust upper rack height (if available). It could be useful to lift up the upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open. To pause the program (e.g.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes... salt indicator is lit rinse aid indicator is lit - Rinse aid dispenser is empty. - Refill dispenser with rinse aid (for more information - see page 3). ...
PAGE 7
What to do if... Crockery and cutlery... ...have deposits: regeneration salt residue Possible causes... Solutions... - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. - Not enough rinse aid. - If you use a combined action detergent, try adding more rinse aid. - Plastic containers dry badly.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.