Self-Cleaning Hot & Cold Hidden Bottle-Water Cooler Model No.: 8LIECH-SCSSFP5W USERS’ MANUAL SAVE THIS MANUAL FOR FUTURE USE For service, call 1-855-594-4755 or e-mail Whirlpool@electrotemp.
Model # 8LIECH-SCSSFP5W: Page 2 TABLE OF CONTENTS Safety Precautions-Electrical Requirements ........................ 2 Safety Precautions ...................................................................... 3 Product Features ........................................................................ 4 Key Information for Future Use ................................................ 4 Specifications ............................................................................... 5 Parts & Features .
Model # 8LIECH-SCSSFP5W: Page 3 SAFETY PRECAUTIONS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and your appliance. Always read and follow all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or injure you and others.
Model # 8LIECH-SCSSFP5W: Page 4 PRODUCT FEATURES Congratulations! You have chosen a technology advanced, state-of-the-art water cooler. To provide consistently cold water, this water cooler forms an "Ice Bank" in the cold tank. Formation of the initial "Ice Bank" can take up to 1 hour. WHEN THE UNIT IS PLUGGED IN FOR THE FIRST TIME, IT CAN TAKE OVER AN HOUR BEFORE THE "ICE BANK " FORMS AND THE UNIT CAN PROVIDE THE COLDEST WATER.
Model # 8LIECH-SCSSFP5W: Page 5 SPECIFICATIONS Energy Verified Power Supply AC 120V / 60Hz / 6.5Amp Refrigerant Type R-134A Cold Water Power <100 Watts Cold Capacity / Hour 4 Litres / 1.06 Gallon Cold Temperature 3°C - 10°C / 37.4°F - 50°F Hot Water Power 650 Watts Hot Capacity / Hour 6 Litres / 1.59 Gallon Hot Temperature 80°C - 92°C / 176°F - 197.6°F Dimensions 1028H mm x 320W mmx 382D mm 40.5H inch x 12.6W inch x 15D inch Net Weight Version 2.0 36.8 Ibs / 16.
Model # 8LIECH-SCSSFP5W: Page 6 UNPACKING AND ASSEMBLY Remove the dispenser from packaging: WARNING TOP TO OPEN: TOP Excessive Weight Hazard TOP TOP Use two or more people to move and install the water cooler and the bottles. Failure to do so can result in back or other injury. 1. Lay the box containing the unit on its side. 2. Open bottom flaps of the cardboard box. 3. Stand cooler upright, with box flaps unfolded. 4. Pull box straight up. 5. Unpack the drip tray and insert it into the dispenser.
Model # 8LIECH-SCSSFP5W: Page 7 SELF-CLEANING - An Exclusive Feature Your water cooler has automatic SELF CLEANING feature to prevent the formation of bacteria laden bio-film and to maintain the original quality of the bottled water. It is not meant to filter or purify dirty water. Water coolers typically grow bio-film and require manual cleaning every 3 months. This machine will do it for you automatically every 4 hours. Carefully measured amounts of ozone are injected to kill harmful bacteria.
Model # 8LIECH-SCSSFP5W: Page 8 Initial Set Up Do NOT plug in until steps 1-3 are completed. WARNING WARNING Excessive Weight Hazard Electrical shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Use two or more people to move and install the water cooler and the bottles. Failure to do so can result in back or other injury. 1.
Model # 8LIECH-SCSSFP5W: Page 9 tube lines. Call 1-855-594-4755 for assistance. 3. Turn the switches at the back of the dispenser to ON. • The red switch controls the hot water. If you do not want hot water, leave this switched OFF. • The blue switch controls the cold water. If you do not want cold water, leave this switched OFF. • For the unit to operate properly, the probe head must seal on the bottle and the door must be fully closed. • It will take less than 3 minutes to fill reservoirs with water.
Model # 8LIECH-SCSSFP5W: Page 10 2. Press the right control downward to start dispensing water. 3. Release the control once desired fill level is achieved. Dispensing Hot Water Note: After setup, hot water will be available in 15-20 minutes. 1. Position the container you wish to fill with water securely below below the hot-water tap. • The left triangle below the hot water control indicates the location of the hot water tap (See the "Parts & Features" section on page 5).
Model # 8LIECH-SCSSFP5W: Page 11 PROPER CARE & DESCALING General Cleaning Perform: As needed Time Required: 5 minutes. Note: Do NOT use abrasive materials or chemical cleaners. 1. Clean cabinet surfaces with a soft cloth and warm soapy water. 2. Wipe dust from back of dispenser to improve the unit’s efficiency. 3. Remove the drip tray assembly by sliding it forward. Remove the cover. Wash both tray and cover in a dishwasher or wipe parts clean with a soft cloth and warm soapy water. 4.
Model # 8LIECH-SCSSFP5W: Page 12 - For descaling once every 6 months, use a mixture of 2 oz. of powdered lemon acid and 3.5 liters of hot water. - For descaling once every year, use a mixture of 4 oz. of powdered lemon acid and 3.5 liters hot water. - For descaling less frequently than once a year, use a mixture of 5 oz. of powdered lemon acid and 3.5 liters hot water. Descaling Procedure 1. Fill a bucket or empty 5-gallon water bottle with the descaling solution of your choice.
Model # 8LIECH-SCSSFP5W: Page 13 12. Replace the drain plug and cap. 13. Place a fresh bottle of water into the machine and operate as usual. 14. This procedure must be repeated every 3 to 6 months, depending on mineral content and usage of water cooler. LED INDICATOR LIGHTS 1 POWER INDICATOR When the LED light is constantly lit it indicates that power is being supplied to the unit. 2 HEATER INDICATOR When the LED light is flashing it indicates that the heating system is working.
Model # 8LIECH-SCSSFP5W: Page 14 TROUBLESHOOTING Call 1-855-594-4755 for service. Problem: Stainless steel surfaces are smudgy or fingerprinted. Solution: Use paper towel to wipe excess oils until surface feels dry to the touch. • To maintain beauty of stainless steel, oil it periodically using a stainless steel cleaning solution available at hardware stores, or use mineral oil (unscented baby oil). Problem: The buttons for dispensing water are slow-moving or jammed.
Model # 8LIECH-SCSSFP5W: Page 15 Problem: Buttons are stuck. Solution: Apply mineral oil (unscented baby oil) to the button slides to reduce friction. Problem: No water is coming from the taps. Solution: Make sure the water bottle is not empty. If it is, replace it. If not, adjust the probe to an appropriate length. • Make sure that you fully press the water controls. • Make sure that the probe connection with the water bottle forms a complete seal. • Make sure that the door is closed.
Model # 8LIECH-SCSSFP5W: Page 16 LIMITED WARRANTY Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship.
®/TM ©2015 Whirlpool. All rights reserved. Manufactured under license by Electrotemp Technologies Inc., Mississauga, ON. Canada Limited warranty provided by manufacturer.