Owner`s manual

ManualsBrandsWhirlpool ManualsHousehold Appliances50 Hz

Jason International, Inc. • 501.771.4477 Page 1 of 9 Customer Service : 800.255.5766

INSPECTION

Inspect the unit prior to installation. In the event of a

problem, DO NOT install the unit. All components are

factory assembled to the bath and the unit is water tested

and inspected prior to leaving Jason International, Inc.

If the carton shows sign of damage, inspect the product before

accepting and describe the problem on the Bill of Lading.

Note: Transportation and insurance from Jason’s factory are

the buyer’s responsibility.

Damage sustained in transit is the responsibility of

the carrier. If damage is discovered, the carrier must

be immediately notified in writing with a request for a

representative to inspect the unit. Failure of the carrier to

respond should be reported to the seller and carrier. Always

file a freight claim promptly.

The installer is responsible for insuring that the unit is free

from defects or shipping damage. In the event of a problem,

DO NOT install the unit. Jason International is not responsible

for damage that might have been avoided by inspection or

testing prior to installation.

Damage to the unit during installation will not be covered

by warranty and is the responsibility of the installer.

ALL WARRANTY CLAIMS ON ACRYLIC SURFACE

DAMAGE MUST BE MADE PRIOR TO INSTALLATION.

Inspect plumbing and bath surface for missing or damaged

components. Alert your dealer of any discrepancies.

To protect the unit from damage keep the bath in the carton

until ready for installation.

EQUIPMENT ACCESS

In accordance with Building Codes, service access to all

therapy bath equipment, controls and electrical connections

must be provided during installation (see Table 1 –

Specifications for minimum access size). Insufficient access

will hinder repair and maintenance. Warranty service will not

cover costs of providing equipment access.

Jason offers an optional removable lateral skirt for all

rectangular baths. The skirts are available in matching acrylic

colors and provide convenient access to bath equipment as

well as an excellent finished appearance.

OWNER’S MANUAL

Integrity

Whirlpool Baths

INSTALLATION, OPERATION, AND MAINTENANCE

“TO BE REMOVED FOR USE BY THE OCCUPANT.”

49-1013-100

Date 02/11

Jason International, Inc.

8328 MacArthur Drive

North Little Rock, AR 72118

www.jasoninternational.com

OWNER’S RECORD

Dealer:

Date Purchased:

Date Installed:

Installer:

PLACE SERIAL NUMBER CARD WITH

PRODUCT CONFIGURATION IN THIS BOX

CAUTION: DO NOT LIFT OR HANDLE THE BATH BY ITS PLUMBING.

If the carton shows sign of damage, inspect

the product before accepting and describe the

problem on the Bill of Lading.

Summary of content (9 pages)

PAGE 1
“TO BE REMOVED FOR USE BY THE OCCUPANT.” Jason International, Inc. 49-1013-100 Date 02/11 8328 MacArthur Drive North Little Rock, AR 72118 www.jasoninternational.com Owner’s Manual Integrity Whirlpool Baths ® INSTALLATION, OPERATION, AND MAINTENANCE If the carton shows sign of damage, inspect the product before accepting and describe the problem on the Bill of Lading. INSPECTION Inspect the unit prior to installation. In the event of a problem, DO NOT install the unit.
PAGE 2
INSTALLATION INSTRUCTIONS TABLE 1 - SPECIFICATIONS (cont.) Integrity Whirlpool TABLE 1 - SPECIFICATIONS Integrity Whirlpool 60 x 60 x 20.5 Operating Capacity Gal Liter 53 152 x 152 x 52 201 B3060 TL 60 x 30 x 20.5 29 152 x 76 x 52 109 B3260 TL 60 x 32 x 20.5 32 152 x 81 x 52 121 B3260 SL/SR 60 x 32 x 20.5 32 152 x 81 x 52 121 60 x 36 x 20.
PAGE 3
Installation Instructions (cont.) INSTALLATION See the USER MAINTENANCE INSTRUCTIONS section of this owner’s manual, prior to installation, for humidity and mold prevention suggestions. 1. Finish Frame: A finish frame under the shell rim should also always be constructed to support the bath deck and insure proper drainage toward the bath well. This frame is not intended to support the full bath weight (see Figures 1 & 2). Jason offers a removable lateral skirt for most baths.
PAGE 4
Installation Instructions (cont.) Figure 3 ELECTRICAL Electrical Power Supply: These instructions are written assuming 60Hz, 120v power supply. Special notations are also included for export versions of the pump, control equipment, and power supply. WARNING: Verification of electrical requirements MUST be made before installation. Refer to the equipment labels for voltage and frequency requirements. NOTE: Verify that the electrical service matches either the 120v or 240v system requirements for this bath.
PAGE 5
Installation Instructions (cont.) cord. Connect the pump to a GFCI (Ground Fault Circuit Interupter) with 240v (volt), 15A (amp), 60HZ (hertz) electrical service with a service ground receptacle dedicated for use by this bath. 6. Export Integrity Whirlpool Control Box (120v,50Hz): This Whirlpool bath is provided with an Air On/Off switch. The pump is pre-wired to a control box which has a 36” cord.
PAGE 6
OPERATING INSTRUCTIONS, FEATURES, AND CONTROLS INTRODUCTION AIR ON/OFF BUTTON This manual contains all of the information needed for the proper operation of this Integrity® Whirlpool bath. The Whirlpool bath has been designed to provide years of relaxing troublefree service, provided the unit is maintained and operated in accordance with these instructions. The Air On/Off button provides a safe and convenient method for controlling the Whirlpool bath.
PAGE 7
USER MAINTENANCE INSTRUCTIONS HUMIDITY SURFACE MAINTENANCE Warning: Avoid high humidity levels in your home. Mold, mildew, fungi and bacteria which may be harmful to health thrive in areas with continued high humidity levels; therefore, every precaution should be taken to make sure your plumbing fixtures including bathtubs, therapy baths, or showers do not become a source of high humidity due to improper installations or leaks.
PAGE 8
TROUBLE SHOOTING GUIDE If the unit is within the warranty period, contact Jason Customer Service: 1-800-255-5766 with the bath’s Product and Serial numbers before work is started. The serial number can be found on the front page of this manual or on the small card adhered to the back of the bath just above the pump. all warranty repairs must be authorized by Jason INTERNATIONAL before work is started.
PAGE 9
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. WARNING: When using this unit, basic precautions should always be followed, including the following: This manual contains information and instructions for proper operation and maintenance of the hydrotherapy bath. Failure to follow these instructions could result in personal injury, electrical shock, or fire.