® ROOM AIR CONDITIONER Use & Care Guide For questions about features, operation/performance, parts, accessories or service call: 1-800-253-1301 or visit our website at... www.whirlpool.com In Canada, call for assistance, installation and service, call: 1-800-807-6777 or visit our website at...www.whirlpool.
TABLE OF CONTENTS AIR CONDITIONER SAFETY .........................................................2 INSTALLATION REQUIREMENTS ................................................3 Tools and Parts ............................................................................3 Location Requirements ................................................................3 Electrical Requirements ...............................................................4 INSTALLATION INSTRUCTIONS .......................................
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic precautions: Plug into a grounded 3 prong outlet. Do not use an extension cord. Do not remove ground prong. Unplug air conditioner before servicing. Do not use an adapter. Use two or more people to move and install air conditioner.
Window Installation Electrical Requirements Window opening measurements: ■ 27" min. to 40" max. (68.6 cm to 101.6 cm) opening width. ■ WARNING 19" min. (48.3 cm) opening height. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. A Do not use an adapter. B Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. A. 27" min. to 40" max. (68.6 cm to 101.6 cm) B. 19" min. (48.
Power Supply Cord INSTALLATION INSTRUCTIONS NOTE: Your unit’s device may differ from the one shown. Unpack the Air Conditioner A B WARNING RESET TEST Excessive Weight Hazard Use two or more people to move and install air conditioner. Failure to do so can result in back or other injury. A. Test button B. Reset button This room air conditioner is equipped with a power supply cord required by UL. This power supply cord contains state-of-the-art electronics that sense leakage current.
Window Installation 1. Using the tray back as a template, center in windowsill against outside edge of stool. C 1. To assemble the tray frame, insert tab on tray back into slot on tray side. Check to see that the tab is engaged and the 2 pieces are aligned. Insert 2 - #8 - 18 x ¹⁄₄" hex-head screws to secure. 2. Repeat with other tray side. C B B A A A. Tray back B. Windowsill C. Outside edge of stool 2.
2. Insert carriage bolt up through slot on tray-frame side and support leg. Install SMART-MOUNT® Tray Assembly in Window 1. From inside, place SMART-MOUNT® tray, support legs facing down, in the window. Match the holes in tray side with the predrilled holes in windowsill. 2. Using 2 - #10 - 12 x 1¹⁄₂" slot-head wood screws, secure the tray frame to the window. A 3. Place one end of tray center over carriage bolt. A.
Prepare Air Conditioner for Window Installation Top View Install Side Curtains NOTE: Attach curtains to unit before placing unit in window. 1. Insert curtain into curtain frame. Make sure curtain end locks into curtain frame. Top View Bottom View Side View 2. Push curtain in all the way. 3. Pull curtain toward open end of curtain frame. 5. Extend right-hand curtain outward so you may insert the first screw through the middle hole of the curtain.
Position the Air Conditioner in Window ■ Handle air conditioner gently. ■ Be sure your air conditioner does not fall out of the opening during installation or removal. ■ Do not block the louvers on the front panel. ■ Do not block the louvers on the outside of the air conditioner. Incorrect Installation A B B C WARNING Excessive Weight Hazard Use two or more people to move and install air conditioner. A. Window sash B. Top channel C.
4. Attach window-lock bracket to window sash with #8 x ³⁄₄" round-head screw to secure window in place. Top View B A A B C A. Side curtain against window channel B. Window channel C. #8 x ³⁄₄" round-head screw A. Upper window sash B. Window-lock bracket Complete Installation 1. Insert foam seal behind the top of the lower window sash and against the glass of the upper window. WARNING A B Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. A. Lower window sash B.
Install Wood Frame A 1. Construct wood frame. See “Location Requirements” for dimensions. 2. Measure outside width and height of frame to determine wall opening dimensions. 3. Cut opening through the wall. Remove and save insulation. NOTES: ■ Dimension for depth depends on wall thickness and type of molding. ■ Do not block louvers in air conditioner cabinet. ■ Use 1" (2.5 cm) or thicker lumber for wood frame. B A. Inside screw holes B. Indoor side of wall opening A 9. Remove the tray back.
Attach Support Legs 1. Determine the correct slots on the tray side from the type of exterior construction of the building. 4. Then place flat washer, lock washer and hex nut. NOTE: Do not tighten. The leg must be able to move freely to adjust angle when installed. A B C D Thin Wall Construction (vinyl, wood, etc.) A E A. Hex nut B. Lock washer C. Flat washer A. First and second slots Thick Wall Construction (brick) A D. Tray center E. Carriage bolt 5.
2. Using 2 - #10 - 12 x 1¹⁄₂" slot-head wood screws, secure the tray-frame assembly to the wall opening. 3. With tray center pushed away from the windowsill, place a level on the angled edge on top of the tray side. Be sure level is against notch on tray side. Left Side B A A. Angled edge on top of the tray side B. Notch A A. #10 - 12 x 1¹⁄₂" slot-head wood screw 4. Adjust SMART-MOUNT® tray until bubble indicates the angled edge on top of the tray side is level.
2. If the feet on the bottom of the air conditioner do not rest on the wood strip, remove the air conditioner and adjust the SMART-MOUNT® tray until feet rest on the wood strip. 4. If the bottom of the air conditioner does not sit against the bottom of the SMART-MOUNT® tray, remove air conditioner and adjust angle of tray until air conditioner sits against the bottom of the tray. IMPORTANT: The tray must slope downward slightly toward the outside to provide proper drainage for the air conditioner.
Start Your Air Conditioner—Digital Control ■ Power Saver—Fan runs only when cooling is needed. You can select the fan speed by pressing FAN SPEED. Because the fan does not circulate the room air continuously, less energy is used, but the room air is not circulated as often. Use Power Saver when you are asleep or away from home. Fan Speed NOTES: ■ When the air conditioner is off, the Room indicator light is lit and the display shows the current room temperature.
Press the minus button to lower the temperature. Room indicator light will turn off, and Set indicator light will turn on. Display shows the Temperature control setting. Each time you press or hold the minus button, the temperature will decrease 1º until it reaches 64°F (18°C). ■ NOTE: After 3 seconds, Set indicator light will turn off, and Room indicator light will turn on. Display will show the current room temperature. 8. Press TIMER again or wait 10 seconds. Timer indicator light will remain on.
To select the mode: Press AUTO COOL, COOL, FAN ONLY, or POWER SAVER. ■ Auto Cool—fan speed is adjusted automatically. ■ Cool, Fan Only or Power Saver—you can adjust the fan speed. To select the fan speed (in Cool, Fan Only or Power Saver mode only): Press TURBO, HIGH or LOW. To set the Timer for a 1- to 24-hour delay until the air conditioner turns off (the air conditioner must be On): 1. Press TIMER. Timer indicator light on air conditioner will flash.
Start Your Air Conditioner—Rotary Control Models Without Power Saver Fan Speed Set FAN SPEED to the desired setting. When the air conditioner is operating at Low Cool, High Cool, or Turbo Cool, the fan circulates air continuously. ■ Turbo Cool—for maximum cooling ■ High Cool—for normal cooling ■ Low Cool—for sleeping comfort ■ Fan Only—to move air continuously without cooling NOTE: Fan runs on Turbo speed only.
Change Air Direction Normal Sounds Roll the wheel to direct the air right or left. Rotate the whole cartridge to direct air up, down or straight ahead. When your air conditioner is operating normally, you may hear sounds such as: ■ Droplets of water hitting the condenser, causing a pinging or clicking sound. The water droplets help cool the condenser. A ■ Air movement from the fan. ■ Clicks from the thermostat cycle. ■ Vibrations or noise due to poor wall or window construction.
TROUBLESHOOTING Before calling for service, try the suggestions below to see whether you can solve your problem without outside help. Air conditioner will not operate WARNING Air conditioner power supply cord trips (Reset button pops out) ■ Disturbances in your electrical current can trip (Reset button will pop out) the power supply cord. Press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.
■ The louvers are blocked. Install the air conditioner in a location where the louvers are free from curtains, blinds, furniture, etc. ■ The outside temperature is below 65°F (18°C). Do not try to operate your air conditioner in the cooling mode when the outside temperature is below 65°F (18°C). ■ The temperature of the room you are trying to cool is extremely hot. Allow extra time for the air conditioner to cool off a very hot room. ■ Windows or doors to the outside are open.
Heavy-Duty Cover If you decide to leave your air conditioner installed during the winter, a heavy-duty cover will help protect your air conditioner and reduce drafts. The outdoor cover protects against cold drafts through the unit's air passages and protects the cabinet from snow, rain, sleet, rust, and dust. For a heavy-duty outdoor cover sized to fit your air conditioner, order Part Number 484069. For a heavy-duty indoor cover sized to fit your air conditioner, order Part Number 4392941.
REQUISITOS DE INSTALACIÓN Herramientas y piezas Requisitos de ubicación Reúna las herramientas y piezas necesarias antes de comenzar la instalación. Lea y siga las instrucciones provistas con cualquiera de las herramientas enlistadas aquí.
Los requisitos eléctricos específicos se indican en la tabla debajo. Siga los requisitos para el tipo de enchufe en el cable de alimentación eléctrica. Instalación a través de la pared Las medidas de la abertura en la pared deben ser: ■ Altura: 18" (45,7 cm) más el doble del espesor de la madera usada para construir el marco. ■ Ancho: 26" (66 cm) más el doble del espesor de la madera usada para construir el marco. ■ Profundidad: 2" (5 cm) mínimo a 8" (20,3 cm) máximo.
ADVERTENCIA Peligro de Choque Eléctrico Conecte a un contacto de pared de conexión a tierra de 3 terminales. 2. Presione RESET (Reposición). 3. Presione TEST (Prueba) (escuche el chasquido, el botón de reposición se dispara y salta). 4. Presione y suelte RESET (escuche el chasquido, el botón de reposición queda asegurado y se mantiene asegurado). El cable de suministro de energía está listo para su funcionamiento. NOTAS: ■ El botón de reposición debe presionarse para el funcionamiento adecuado.
Instalación en la ventana 1. Usando la barra posterior de la bandeja como plantilla, céntrela en la parte inferior de la ventana contra la parte posterior del marco de la ventana. C 1. Para ensamblar el marco de la bandeja, inserte la lengüeta de la barra posterior de la bandeja dentro de la ranura lateral de la bandeja. Verifique que la lengüeta esté insertada y que las 2 piezas estén alineadas. Coloque 2 tornillos de cabeza hexagonal #8 - 18 x ¹⁄₄" para asegurarla. 2.
2. Empuje el perno de carruaje hacia arriba en la ranura del lado del marco de la bandeja y la pata de soporte. Instale el ensamblaje de la bandeja SMART-MOUNT® en la ventana 1. Desde adentro, coloque la bandeja SMART-MOUNT® en la ventana con las patas de soporte mirando hacia abajo. Haga coincidir los orificios de las barras laterales de la bandeja con los orificios pilotos en el marco de la ventana. 2.
5. Ajuste la tuerca hexagonal solamente lo suficiente para mantener la barra central de la bandeja en su lugar. 6. Repita el procedimiento con el otro lado. 7. Ajuste con seguridad las tuercas hexagonales con una llave para tuercas de ⁷⁄₁₆". Prepare el acondicionador de aire para la instalación en una ventana Vista superior Instalación de las cortinas laterales NOTA: Sujete las cortinas a la unidad antes de colocar la unidad en la ventana. 1. Inserte la cortina en el marco de la cortina.
Colocación del acondicionador de aire en la ventana ■ Trate el acondicionador de aire con cuidado. ■ Asegúrese de que el acondicionador de aire no se caiga de la abertura durante la instalación o al quitarlo. ■ No bloquee las rejillas que están en el panel delantero. A ■ No bloquee las rejillas que están en el exterior del acondicionador de aire. B ADVERTENCIA C Instalación correcta Peligro de Peso Excesivo Use dos o más personas para mover e instalar el acondicionador de aire.
Fije las cortinas laterales a la ventana 1. Jale de la cortina izquierda hacia afuera hasta que encaje en la ranura de la ventana. Repita el procedimiento para la cortina derecha. 2. Inserte uno de los tornillos de cabeza redonda #8 x ³⁄₄", a través del marco de la cortina izquierda en la ranura de la ventana para asegurar el marco de la cortina a la ventana. 3. Repita el procedimiento para el marco de cortina derecha. 2.
Instalación a través de la pared Opción 1—Moldura de madera, metal o plástico Cuando utilice una moldura de madera, metal o plástico, el marco de madera debe estar alineado con la pared interior como se muestra. ■ Utilice madera de 1" (2,5 cm) o más gruesa para el marco de madera. A A B C B D C A. Ancho exterior B. Altura exterior C. Profundidad A. Moldura B. Pared interior C. Marco de madera D.
A Fije las patas de soporte 1. Determine las ranuras correctas de la barra lateral de la bandeja basándose en el tipo de construcción exterior del edificio. Construcción de pared delgada (vinilo, madera, etc.) B A A. Orificios de los tornillos interiores B. Lado interno de la abertura de la pared 9. Saque la barra posterior de la bandeja. Usando estas marcas, taladre orificios piloto de ³⁄₃₂", de aproximadamente 1¹⁄₂" (3,8 cm) de profundidad. Ensamblaje de la bandeja SMART-MOUNT® A.
4. Luego coloque la arandela plana, la arandela de presión y la tuerca hexagonal. NOTA: No las apriete. La pata se debe mover libremente para poder ajustar el ángulo después de que esté instalada. 2. Usando 2 tornillos para madera de cabeza ranurada #10 - 12 x 1¹⁄₂", asegure el ensamblaje de la bandeja con el marco a la abertura de la pared. Lado izquierdo A B C D E A. Tuerca hexagonal B. Arandela de presión C. Arandela plana D. Barra central de la bandeja E. Perno de carruaje 5.
4. Ajuste la bandeja SMART-MOUNT® hasta que la burbuja indique que el extremo con ángulo sobre el lado de la bandeja está nivelado. IMPORTANTE: La bandeja debe estar inclinada levemente hacia abajo y hacia fuera para que el acondicionador de aire desagüe adecuadamente. 5. Ajuste la tuerca hexagonal sólo lo suficiente para mantener el centro de la bandeja en su lugar. 6. Repita el procedimiento con el otro lado. 7. Ajuste con seguridad las tuercas hexagonales con una llave para tuercas de ⁷⁄₁₆". A B A.
3. Si el canal superior no descansa contra la parte superior de la abertura de la pared, saque el acondicionador de aire y ajuste la bandeja SMART-MOUNT® hasta que el canal superior descanse contra la pared. IMPORTANTE: La bandeja debe estar inclinada levemente hacia abajo y hacia fuera para que el acondicionador de aire desagüe adecuadamente. A Complete la instalación 1. Selle y corte alrededor del acondicionador de aire en el interior y en el exterior.
CÓMO USAR SU ACONDICIONADOR DE AIRE Operar debidamente su acondicionador de aire le permite obtener los mejores resultados posibles. Esta sección le explica cómo operar su acondicionador de aire debidamente. IMPORTANTE: ■ Si usted apaga el acondicionador de aire, espere por lo menos 3 minutos antes de volver a ponerlo en marcha. Esto evitará que se queme un fusible o se dispare un disyuntor de circuito a causa del acondicionador de aire.
Monitor del filtro 1. Cuando la luz indicadora Filter (filtro) se encienda o destelle, saque, limpie y reemplace el filtro. Vea “Limpieza del filtro de aire”. 2. Presione y sostenga FILTER (filtro) por 3 segundos después de limpiar y reemplazar el filtro de aire. Esto vuelve a fijar el monitor del filtro. NOTA: Después de que el ventilador funcione por 360 horas, la luz indicadora del filtro se encenderá. Permanecerá encendida por 180 horas o hasta que usted presione FILTER (filtro).
Para borrar la programación del tiempo de retardo del temporizador: NOTA: El acondicionador de aire puede estar encendido o apagado. Presione y sostenga TIMER por 3 segundos. La luz indicadora Temporizador se apagará. Para ver o cambiar el tiempo restante (en horas): 1. Oprima TIMER una vez después de que haya sido programado. La luz indicadora Hour (hora) se encenderá y la pantalla mostrará las horas restantes. 2.
Para programar el temporizador para un retardo de 1 a 24 horas hasta que el acondicionador de aire se apague (el acondicionador de aire tiene que estar Encendido): 1. Oprima TIMER. La luz indicadora Temporizador en el acondicionador de aire destellará. La luz indicadora Hour (hora) en el acondicionador se encenderá y la pantalla en el acondicionador mostrará las horas restantes antes de que se apague el acondicionador de aire. 2.
Fan Speed (Velocidad de ventilación) Ponga el control de FAN SPEED (Velocidad de ventilación) en la posición que desee. Cuando el acondicionador de aire está funcionando a temperaturas Low Cool (Poco fría), High Cool (Muy fría) o Turbo Cool (Máximo nivel de frío), el ventilador hace circular el aire continuamente.
CÓMO CUIDAR SU ACONDICIONADOR DE AIRE Su nuevo acondicionador de aire está diseñado para darle muchos años de servicio confiable. Esta sección le da la información acerca de la limpieza adecuada y el cuidado de su acondicionador de aire. Llame al vendedor autorizado de su localidad para un chequeo anual. Acuérdese…el precio de esta llamada de servicio es su responsabilidad. 3. Limpie el filtro de aire usando una aspiradora. Si está muy sucio, lave el filtro de aire con agua tibia y un detergente suave.
■ El acondicionador de aire no tiene el tamaño adecuado para su habitación. Verifique la capacidad de enfriamiento de su acondicionador de aire para habitación. Los acondicionadores de aire para habitaciones no están diseñados para enfriar varias habitaciones. ■ El filtro está sucio u obstruido por desechos. Limpie el filtro. ■ El evaporador interno y los serpentines del condensador externo están sucios u obstruidos por desechos. Vea “Mantenimiento Anual”.
AYUDA O SERVICIO TÉCNICO Antes de solicitar ayuda o servicio técnico, por favor consulte la sección “Solución de Problemas”. Esto le podría ahorrar el costo de una visita de servicio técnico. Si considera que aún necesita ayuda, siga las instrucciones que aparecen a continuación. Cuando llame, tenga a mano la fecha de compra y el número completo del modelo y de la serie de su electrodoméstico. Esta información nos ayudará a atender mejor a su pedido.
1188018B © 2005 Whirlpool Corporation. 12/05 All rights reserved. ® Registered Trademark/TM Trademark of Whirlpool, U.S.A. Whirlpool Canada LP Licensee in Canada Printed in U.S.A. Todos los derechos reservados. ® Marca registrada/TM Marca de comercio de Whirlpool, U.S.A., usada bajo licencia de Whirlpool Canada LP en Canadá Impreso en EE.UU.