Technical Manual Key Fob Reader (RFID Reader) BLK 100 with serial interface for washers and dryers - version 1.
Technical Manual BLK 100 0. WH Münzprüfer Dietmar Trenner GmbH, Germany Safety Precautions You are advised to observe the safety information during operation, maintenance and repairing of the BLK 100. Failure to do so may result in warranty and other claims being excluded. Whilst every care has been taken in the preparation of information contained in this manual, WH Münzprüfer Dietmar Trenner GmbH will not be liable for any consequential loss or damage howsoever caused.
WH Münzprüfer Dietmar Trenner GmbH, Germany Technical Manual BLK 100 Table of Contents 0. Safety Precautions ................................................................................2 1. 1.1. 1.2. 1.3. Introduction .........................................................................................4 Technical Data BLK 100 .....................................................................4 RFID Card Reader Functionality BLK 100 .............................................
Technical Manual BLK 100 1. WH Münzprüfer Dietmar Trenner GmbH, Germany Introduction The key fob reader BLK 100 offers payment with NFC keys. Keys can be charged at the Central Pay Machine CPM 100 inside the laundry facility. 1.1. Technical Data BLK 100 supply voltage 8 to 16 V DC These are the absolute limiting values. To ensure the undisturbed performance of the BLK 100 the applied voltage should be within these ranges and must never drop below or rise higher even in worst cases.
WH Münzprüfer Dietmar Trenner GmbH, Germany Fig. 1 Technical Manual BLK 100 LEDs, user interface BLK 100 If the red LED is on continuously the process failed. Fig. 2 Red LED on, a failure occurred If the red LED is flashing with the key in front of the key fob reader an invalid “Pay Key” (wrong operator or wrong currency) has been presented. 2. Serial Interface The serial interface of the key fob reader BLK 100 communicates with different protocols with the machine controller.
Technical Manual BLK 100 WH Münzprüfer Dietmar Trenner GmbH, Germany On the back of the key fob reader you have to press the push button e.g. with a paper clip as indicated below. Fig. 3 Location of the push button Once the key is pressed the LEDs red and green are switched on. Within 40 seconds the “Operator Key” must be presented in front of the reader. If the process is successful the red LED turns off and the green LED flashes 5 times. If the red LED is on continuously the process failed. 4.
WH Münzprüfer Dietmar Trenner GmbH, Germany 5. Technical Manual BLK 100 BLK 100 Label The label of the BLK 100 has all the necessary information required to identify it. The following section explains and clarifies the format and legend on the label. Fig. 4 Example of an BLK 100 label Below the firmware version the exact type of BLK 100 is printed. Below the barcode is the serial number and the week and year of manufacture. The same information is contained in the bar code.
Technical Manual BLK 100 7.
WH Münzprüfer Dietmar Trenner GmbH, Germany 8. Technical Manual BLK 100 Compliance Statements FCC / ISED for BLK 100 FCC ID: 2AVM3BLK100 IC: 25831-BLK100 8.1. USA - User Manual Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Technical Manual BLK 100 WH Münzprüfer Dietmar Trenner GmbH, Germany L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : L’appareil ne doit pas produire de brouillage.
WH Münzprüfer Dietmar Trenner GmbH, Germany 9. Fig. 5 BLK 100 Technical Manual BLK 100 Dimensions Dimensions of BLK 100 version 1.