Installation Guide

ManualsBrandsWG Wood Products ManualsBathLeesburg 4.25 x 15.5 x 31.5 Unfinished Bathroom Storage Wall Cabinet

2020 On the Wall2022-On the Wall cabinet Installation Instructions Page 1 of 5

2022 Installation Instructions

for ON-the wall

Cabinets

Tools Needed:

Stud Finder, Tape Measure, Pencil, Hammer, drill, 1/8” Drill Bit, Phillips Screwdriver,

Phillips Tip, Level

Depending on product ordered, your cabinet may be unfinished, primed or already pre-

finished in a color. If your cabinet is unfinished or primed, remove the hinges and store

them in a safe place with the screws. Then paint or stain the cabinet as desired. Primed

doors can only be painted, not stained. If you want to add hardware to your door after

painting or staining, it will be easier to drill for the necessary holes with the door off of

the cabinet.

The mounting brackets (See figure A) have already been placed inside the cabinet for you.

And the back panel has already been mounted in place with framing tabs which bend

over to secure it. If you need to remove it, simply bend the tabs back and pull the panel

out. Be sure to put it back in the proper orientation so that it lines up with the holes in

the mounting brackets.

Determine the placement on the wall and mark the location of the mounting brackets on

the wall surface. Check to see where studs are in your wall. If your locations match up,

great. If not, you can use the included wall anchors instead.

If using wall anchors, screw those directly into the wall surface (See Figure B) until they are

flush. Drilling a 1/8” hole will help the anchor to go in easier and faster. Wall anchors

are designed to go in with a phillips bit on your drill. Then place the cabinet on the wall

and line up the brackets with your wall anchors and use the 2” screws to mount the

cabinet to the wall. Be sure to use a level on the cabinet.

Hinge mounting holes have been pre-drilled on either side of the cabinet so that it

is reversible. Mount the door on whichever side you desire. Remove the cover

cap on each hinge. (See figure E) Re-attach your hinges if you have taken them off

of the door. Have a partner help you by holding the door into place while you do

the installation, it’s easier! Place the door on the side of the cabinet and line up

the hinges with the hinge holes marked on that side of the cabinet box. Screw

the ¾” screws (Hardware Bag labeled “Hinge screws”) into the hinge hole (see figure C).

The hinge should be resting right on the FRONT edge of the cabinet box itself.

Install your plastic shelf supports (Hardware package labeled - Shelf supports) at the

desired locations (See figure D) and insert the shelves into place. Replace hinge

cover caps.

Summary of content (5 pages)

PAGE 1
2022 Installation Instructions for ON-the wall Cabinets Tools Needed: Stud Finder, Tape Measure, Pencil, Hammer, drill, 1/8” Drill Bit, Phillips Screwdriver, Phillips Tip, Level Depending on product ordered, your cabinet may be unfinished, primed or already prefinished in a color. If your cabinet is unfinished or primed, remove the hinges and store them in a safe place with the screws. Then paint or stain the cabinet as desired. Primed doors can only be painted, not stained.
PAGE 2
Image 4 Dry wall anchor in pilot hole Figure B. Figure A. Our custom designed shelf supports keep the shelves in place and do not allow the shelves to rock or come off the supports. Simply slide your shelves in and out of them. Orient your shelf supports UP as shown here UP Figure D. Figure C.
PAGE 3
Figure E. Hints and Tips for a Great Installation We use a one piece Blum concealed hinge with a built in Blumotion soft close option. The hinges are installed in all the doors. Due to various sizes of cabinets and doors we may ship the door separately from the cabinet to insure the door and hinges will arrive intact and undamaged. (Exception: Cabinets with slab MDF Doors which must be painted) If this is the cabinet style you purchased the hinges are located in the hardware bag labeled “MDF Door”.
PAGE 4
Hinge Adjustments There are 4 adjustments on this hinge. See image below Adjustment #1 - Use this screw to move the door towards or away from the front of the cabinet box (to close the gap between the door and the box). It will only turn about ¼ turn either way. Adjustment #2 – Use this screw to move the door side to side. It will only turn about ¼ turn either way. Adjustment #3 – This switch is for full soft close or partial soft close. See tips on last page.
PAGE 5
3 4 The door is warped: Solid wood doors do occasionally warp due to final drying of the wood. There is a simple test you can perform to ensure that your door is not warped. Remove the hinges by taking out the four screws holding them in. The hinges will then just pull out (though they do fit in the holes tightly). Now lay the door down face up on a flat surface such as a table or counter. If the door can rock from corner to corner, it may be warped. 98% of doors will lay perfectly flat.