58Khz WiFi Common Platform EAS Systems (EAS 5.0 ver 1.6 AM Board) Installation Manual December 2013 Manual Ver.
WARRANTY DISCLAIMER WG Security Products Inc. makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, WG Security Products Inc. reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of WG Security Products Inc. to notify any person of such revision or changes.
TABLE OF CONTENTS OVERVIEW ..................................................................................................................... 1 System Overview ......................................................................................................... 1 System Configurations................................................................................................. 2 Product Names and Part Numbers ..............................................................................
(THIS PAGE INTENTIONALLY LEFT BLANK)
Common Platform WiFi EAS Systems OVERVIEW System Overview Common Platform WiFi EAS Systems differ only in the antennas that are used. All systems use a universal transceiver printed circuit board that performs all the functions of transmitting, receiving and alarm notification. This manual applies to WiFi versions of the Ad Guard, Ad Guard XL, Premier Guard, Premier Pro, and Lane Guard. A separate manual is available for WiFi versions of the Floor Guard and Door Guard.
Common Platform WiFi EAS Systems Detection Range on Both Sides of Antennas with Micro Pencil Tags Antenna Type USA Europe 3 ft 0.9 m 4.5 ft 1.4 m 3 ft 0.9 m Premier Pro 4.5 ft 1.4 m Lane Guard 3 ft 0.9 m Ad Guard Ad Guard XL Premier Guard System Configurations Each transceiver pedestal is powered by its own dedicated SPS. The SPS not only provides 24vac power to the transceiver pedestal, but it includes some very important features.
Common Platform WiFi EAS Systems Common Platform Features & Benefits All-in-One platform design for the Acousto-Magnetic (AM) product line makes it a perfect AM detection core solution for various antenna forms and needs. There are visible advantages on short term and long term operation along with low cost maintenance.
Common Platform WiFi EAS Systems Specifications Smart Power Supply (WG SPS-24) Electrical 100vac 10 % Primary Input (Stepdown Transformer) 110vac 10 % 120vac 10 % 220vac 10 % 240vac 10 % Secondary Output 26Vac 5 % Rated Output Current 1.8A Maximum Secondary Output Current 1.9 A Built-in Fuse (self-resettable) 500mA Smart Power Supply (WG SPS-24) Mechanical Height 3.15” (80mm) Width 4.33” (110mm) Thickness 5.5” (140mm) Weight 6.
Common Platform WiFi EAS Systems COMMON PLATFORM ELECTRONICS Control Board Resonant Board 5
Common Platform WiFi EAS Systems SMART POWER SUPPLY (SPS) SPS Controls and Connections SPS Front View SPS Power On/Off Switch Fuse Replacement: Internal AC Fuse Rating (T3.15AL, 250V) Caution! Disconnect power before servicing.
Common Platform WiFi EAS Systems SPS Terminals N - GND - L Pin: 1 2 3 Main AC Input Terminal SPS Main AC Input Terminal Layout Main AC Cable (3 wires) Pin Function Color 1 Neutral White 2 Ground Green 3 Hot Black LED Status Pin: 1 2 3 4 5 6 7 8 9 LED On Off TX Off TX is Off TX is On System Alarm Alarm Enabled Alarm Disabled Jammer Detection Detection Enabled Detection Disabled Alarm Volume Dim Means Weaker Bright Means Louder 10 SPS Output Terminal Layout (10 pins) SPS to P
Common Platform WiFi EAS Systems SPS Box Main AC Input and Voltage Setup The Smart Power Supply (SPS) box accepts 5 input voltages: 100vac 110vac and 120vac in North America and Japan, 220vac and 240vac in Europe and Australia. Caution: Set the two Voltage Switches (A and B) on the SPS at the specified combination based on the local incoming voltage value (see picture below).
Common Platform WiFi EAS Systems Interconnection between Smart Power Supply and Pedestal The system transceiver board has two sockets (combined pins 1 to 6) that connect to SPS output terminal pins 1 to 6 (one-to-one pin connection). The reference diagram shows the pin mapping relation between transceiver board and PSU. Isolated Multiple Conductor Cable Pin 1 Pin 1 Un-Shielded Pin 6 Pin 6 Caution! One SPS can power only one transceiver pedestal.
Common Platform WiFi EAS Systems Power Cord Notices The SPS delivered does not include AC cable for installation; we recommend that you use a CE approved power cord H05 VV-F or H05 VVH2-F2 (Refer to the Electrical code which governs your country for installation of an Anti-Theft Unit to the Main power Supply) with the cable specification and gauge provided below.
Common Platform WiFi EAS Systems International Power Supply Cord Here is a sample of qualified external power line at one end with three close loop lugs connector and a molded receptacle terminal block at the other end. Conductors are CEE color-coded—light blue (neutral), brown (line) and green/yellow (ground). Other IEC 320 C-13 type power supply cords can be used if they comply with the safety regulations of the country in which they are installed. Closed loop lugs must be used as shown.
Common Platform WiFi EAS Systems SPS Box Mounting Instructions For installation safety and security, the SPS power supply box shall be mounted into local certified electric distribution box. Installer must use local certified AC cable at AWG18 and a certified circuit breaker at 15A or 20A to disconnect main power from the SPS unit. And then from distribution box, installer can direct the output cable from each SPS to local pedestal at different sites.
Common Platform WiFi EAS Systems 1. Hang the SPS box onto the upper flange of mounting rail. Mount Rail 2. Close up the bottom of SPS box with the mounting surface and lock the lower flange of mounting rail.
Common Platform WiFi EAS Systems SPS Box External Relay interface The external relay interface is located at Output side of the SPS. Suggested Relay Ratings 1A@ 24 VDC Last 4 pins on this end. Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 SPS Output Terminal Layout (10 pins) Alarm Relay SPS to Pedestal Cable (6 wires) Pin # 1 2 3 4 5 6 Function GND 24VAC TX OFF Alarm AntiJammer Alarm Volume 7 Jammer Relay 8 1A Contact Rating Electrical Notes: 1.
