TM 58Khz BTL Common Platform EAS Systems (EAS4.0 ver1.1 AM board) Installation Manual February 2012 Manual Part Number: (Ver.
WARRANTY DISCLAIMER WG Security Products Inc. makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, WG Security Products Inc. reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of WG Security Products Inc. to notify any person of such revision or changes.
WG SECURITY PRODUCTS INC. 3031 Tisch Way, Suite 602, San Jose, CA 95128 (USA) http://www.wgspi.com Technical Support Contact Information North America South America Tel: 949-545-6005 Toll Free: 888-633-5095 Fax: 949-545-6011 Email: service@wgspi.com Rest of World Tel: 4+49 8654 7715-21 Fax: 4+49 8654 7715-21 Email: support-ROW@wgspi.com CRITICAL NOTE As specified by FCC Regulations 15.
TABLE OF CONTENTS OVERVIEW................................................................................................................ 1 System Overview.................................................................................................... 1 System Configurations............................................................................................ 2 Product Names and Part Numbers .........................................................................
Common Platform EAS Systems OVERVIEW System Overview Note: Common Platform EAS Systems differ only in the antennas that are used. All systems use a universal transceiver printed circuit board that performs all the functions of transmitting, receiving and alarm notification. This manual applies to AdGuard, AdGuard XL, Lane Guard and Diamond Door Guard. The common platform line of products consist of one or more pedestals (transceiver antenna and optional extender), and one external PSU unit (WG SPS24).
Common Platform EAS Systems System Configurations Each transceiver pedestal is powered by its own dedicated SPS. The common platform SPS not only provides 24vac power to the transceiver pedestal, but it includes some very important features.
Common Platform EAS Systems Product Names and Part Numbers Accessories Accessory Name Order Number 1. Smart Power Supply (SPS unit) WG SPS24 2. Instruction Manual 3. Power Line Connector (2 pins) 4. Communication Connector (4 pins) 5. Laptop Tuning Software 6. Serial Tuning Cable 7. USB to Serial Convertor 8. WG IR Tuning Module Systems Antenna Name Order Number 1. AdGuard BTL Transceiver Pedestal WG BTLAG 2. AdGuard BTL Slave Pedestal WG BTLAG-EX 3.
Common Platform EAS Systems Common Platform Features & Benefits • All-in-One platform design for the Acousto-Magnetic (AM) product line makes it a perfect AM detection core solution for various antenna forms and needs. There are visible advantages on short term and long term operation along with low cost maintenance.
Common Platform EAS Systems Specifications (common parameters) Smart Power Supply (SPS) Electrical 100vac ±10 % Primary Input (Stepdown Transformer) 110vac ±10 % 120vac ±10 % 220vac ±10 % 240vac ±10 % Secondary Output 26Vac ±5 % Rated Output Current 1.8A Maximum Secondary Output Current 1.9 A Built-in Fuse (self recovery) 500mA Smart Power Supply (SPS) Mechanical Height 80mm ( 3.15” ) Width 110mm ( 4.33” ) Thickness 140mm ( 5.5” ) Weight 3 Kg ( 6.
Common Platform EAS Systems COMMON PLATFORM ELECTRONICS BTL AM Board Functions Description Tuning Socket (WG Digitool) DSP Area Receiver Area 485 Control for Slave Pedestal Pedestal LED &Alarm Socket Power Supply Sockets (WG SPS-24) Transformer Transmitter 6 Antenna Sockets
Common Platform EAS Systems Antenna Channels on BTL AM Board Some pedestal types may have internal auxiliary RX coil antenna and connect to this socket. Receiver Aux Coil CH 2P Slave RX signal CH 2P Ferrite Phase Switch (Default: low) Tips: The ferrite channel phase switch is useful when sometime install run into high noise environmental and two ferrite rod antennas may have additive noise value to block up the RX channel. Switch the phase may bring noise down.
Common Platform EAS Systems TX Amplitude POT on BTL AM Board Transmitter Fig8 coil resistance (Factory set) Transmitter Loop coil resistance (Factory set) 8
Common Platform EAS Systems BTL AM Board to Socket Board Power Cables Connections BTL AM Board Backside Socket Board Pin1 Pin2 Pin3 Pin # Function Cable color 1 12V Brown Pin5 2 5V Red Pin6 3 empty Orange Pin7 4 GND Yellow Pin8 5 Alarm Volume Green Pin9 6 Anti-Jammer Blue 7 Alarm Purple 8 TX OFF Grey 9 24V White 10 +32V Black 11 GND Brown 12 -32V Red Pin4 Pin1 9 Pin10 Pin11 Pin12 Pin1
Common Platform EAS Systems Pedestal Socket Board Connections Cap Tuning Jumpers AD-Guard and Premier Guard BTL series systems has a socket board on pedestal to facilitate TX caps tuning and trans-connect all antenna connections and PSU power connections to BTL AM board.
Common Platform EAS Systems PSU Power and Control Socket To AM Board From WG-SPS24 Pin1 Pin1 J4 J5 Function I/O Cable color 1 GND Common GND Brown (white) 2 24VAC 26vac±5% Red 3 TX OFF Output Orange 4 Alarm Input Yellow 5 AntiJammer Input Green 6 Alarm Volume Output Blue Pin # J6 Pin # Function Cable color 1 Ferrite CH1 Black 2 Ferrite CH1 Red 3 Ferrite CH2 Black 4 Ferrite CH2 Red 6 Alarm Red 7 Alarm Black 5 11
Common Platform EAS Systems Fuse Replacement Information (on BTL socket Board) The fuse holder is accessed through the socket board side of pedestal. Fuse Replacement: 5mm x 20mm 3.15A (Fast Fuse) 1. Equipment shall be electrically disconnected from the main circuit supply when replacing the fuse. 2. Remove the fuse holder with a screwdriver, rotating it in a counterclockwise direction. 3. Replace the fuse in accordance with the specification noted above.
Common Platform EAS Systems Pedestal Tuning Access (on BTL AM Board) Common Platform systems include advanced tuning features that offer the technician a choice of access. There is a connector on the Transceiver PCB for tuning access. The installer can connect to the pedestal using a laptop PC with a WG connection cable or attach an external IR tuning and display module. The same dedicated tuning connector on the transceiver board accepts both the WG USB cable and external IR tuning and display module.
Common Platform EAS Systems SMART POWER SUPPLY (SPS) SPS Controls and Connections SPS Front View SPS Power On/Off Switch Fuse Replacement: Internal AC fuse rating (T3.15AL, 250V) Caution! Remove power before service.
Common Platform EAS Systems SPS Box Terminals Illustration SPS Main AC Input Terminal Layout Main AC Cable (3 wires) Pin Function Color 1 Neutral Blue 2 Ground Green w/Yellow Stripe 3 Live Red(Brown) N - GND - L Pin: 1 2 3 Main AC Input Terminal LED Status Pin: 1 2 3 4 5 6 7 8 9 LED On Off TX Off TX is Off TX is On System Alarm Alarm Enabled Alarm Disabled Jammer Detection Detection Enabled Detection Disabled Alarm Volume Dim Means Weaker Bright Means Louder 10 SPS Output T
Common Platform EAS Systems SPS Box Main AC Input and Voltage Setup The Smart Power Supply (SPS) box accepts 5 input voltages: 100vac 110vac and 120vac in North America and Japan, 220vac and 240vac in Europe and Australia. Caution: Set the two Voltage Switches (A and B) on the SPS at the specified combination based on the local incoming voltage value (see picture below).
Common Platform EAS Systems Interconnection between Smart Power Supply and Pedestal The system transceiver board has two sockets (combined pins 1 to 6) that connect to SPS output terminal pins 1 to 6 (one-to-one pin connection). The reference diagram shows the pin mapping relation between transceiver board and PSU. WG SPS-24 Socket Board Isolated Multiple Conductor Cable Pin 1 Pin 1 Un-Shielded J4 J5 Pin 6 Pin 6 Caution! One SPS can power only one transceiver pedestal.
Common Platform EAS Systems Power Cord Notices The SPS delivered does not include AC cable for installation; we recommend that you use a CE approved power cord H05 VV-F or H05 VVH2-F2 (Refer to the Electrical code which governs your country for installation of an Anti-Theft Unit to the Main power Supply) with the cable specification and gauge provided below.
Common Platform EAS Systems International Power Supply Cord Here is a sample of qualified external power line at one end with three close loop lugs connector and a molded receptacle terminal block at the other end. Conductors are CEE color-coded—light blue (neutral), brown (line) and green/yellow (ground). Other IEC 320 C-13 type power supply cords can be used if they comply with the safety regulations of the country in which they are installed.
Common Platform EAS Systems SPS Box Mounting Instructions For installation safety and security, the SPS power supply box shall be mounted into local certified electric distribution box. Installer must use local certified AC cable at AWG18 and a certified circuit breaker at 15A or 20A to disconnect main power from the SPS unit. And then from distribution box, installer can direct the output cable from each SPS to local pedestal at different sites.
Common Platform EAS Systems SPS Box External Relay interface The external relay interface is located at Output side of the SPS. Suggested Relay Ratings 1A@ 24 VDC Last 4 pins on this end. Pin 1 Pin 2 Pin 3 Pin 4Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 SPS Output Terminal Layout (10 pins) Alarm Relay SPS to Pedestal Cable (6 wires) Pin # 1 2 3 4 5 6 Function GND 24VAC TX OFF Alarm AntiJammer Alarm Volume 7 Jammer Relay 8 1A Contact Rating Electrical Notes: 1.
