TM REV 8 and REV 10
Owner’s Manual & “Limited” Warranty Technology Specifications: Thank You for purchasing this Wet Sounds product. Wet Sounds marine audio products represent the ultimate in high performance standards. The Revolution Series is specifically engineered to withstand the rigorous marine environment. Utilizing the state of the art acoustic engineering and three dimensional computer aided design, our “Revolution Technology” represents the most advanced technologies available for wakeboard tower speaker systems.
wakeboard tower speakers to the next level, Wet Sounds has consulted with experts who spent countless hours examining the human auditory system to find out which frequencies affect your ears the most at loud volumes. The Revolution series has been designed from the ground up to provide stunning output while eliminating certain frequencies that give that “ringing” or harsh sound associated with loud volumes.
Installation: REV8 FC and REV 10 FC TC3-F Fixed Clamp Pipe Version Installation (pipe tower)
Step 1: Attach Male Connector (7) from clamp base to Female Connector (8) Step 2: Push connector into center hole of speaker as you place clamp base onto the speaker housing. Please make sure the grommet (9) is seated properly. Step 3: Attach two short Allen Bolts (4) through the clamp base and tighten into the housing. Please make sure these are tight. It is also recommend to use a Blue Loctite on these bolts.
Installation: REV8 SC and REV 10 SC “Patent Pending” TC3-S Swivel Clamp Version Installation
Pipe Tower Mount Version using the TC3-S Step 1: Attach Male Connector (10) from clamp base to Female Connector (11) Step 2: Push connector into center hole of speaker as you place clamp base onto the speaker housing. Insert 4 bare wires down into this hole as well. These wires are only used if you are adding the LED speaker rings. (please see LED speaker install instructions for LED install) Please make sure the grommet (12) is seated properly.
Step 7: Attach Clamp Top (2) to clamp bottom (3) using the two long Allen Bolts (1) Step 8: Make sure the clamp is tightened all the way so there is no movement Step 9: The swivel clamp allows you to rotate the speaker any direction you may want. Loosen the allen locking bolt (19) and rotate the speaker to the direction you like. Then tighten the bolt to lock it in place. Step 10: The swivel clamp also allows you to remove the speaker from the tower in seconds.
Step 5: The detachment plate (5) will be hard mounted to a cast tower. Butt connect speaker wires from detachment plate connector (4) to the speaker wires from the cast tower. Red is positive and Black is negative. Step 6: Push wires into center hole back into the tower and attach the detachment plate to the tower. Step 7: Please make sure the male speaker plug (7) and female speaker plug (4) are lined up properly. The male speaker plug (7) inside the clamp base can rotate.
X Mount Version. Cast tower fixed mount version. Step 1: Remove 4 screws holding the grille and driver onto the housing. And remove the grille and speaker from the housing. Disconnect speaker wires from mid bass and compression driver. Remove acoustic dampening material. Step 2: Remove two small Phillips screws from the top of the housing next to the grommet (2) This will loosen the internal threaded plate.
Step 3: From inside the housing. Slide out the internal threaded plate and replace with non threaded plate from X kit. Make sure to install it in the same direction so the screw holes line up. Step 4: Take the two powder coated top plates and attach on top of the speaker. Use two longer Phillips screws provided in the X kit to attach top plates into internal non threaded plate. Step 5: Butt connect Male Connector (1) to the factory wires. Red for positive and black for negative.
“Limited Warranty” What This Warranty Covers This is a "Limited" warranty. This warranty covers any defects in materials and workmanship and warranty only applies to the original purchaser and is not transferable. This warranty is also only valid if the original purchase was made from an authorized Wet Sounds™ dealer. How Long Coverage Last This warranty runs for 2 years from the date of the purchase. It is recommended to REGISTER your warranty online within 45 days of your purchase at www.wetsounds.
How to Obtain Warranty Service Contact Wet Sounds, Inc. either by phone at 877-938-7757 or by email at warranty@wetsounds.com. A service representative will assist you in the necessary actions to verify that the problem that you are experiencing is covered under warranty. If it is in fact a warranty issue, Wet Sounds will issue an RA number for tracking purposes and give instructions on sending the product in for evaluation. Wet Sounds™, Inc.
